5 replies to this topic

[nasky]

Hello,

 

I have the usb dvb RTL2832 with tuner R820T and I have problem to work with VU+ UNO. The same tuner in ET9000 works perfect.

 

This are the logs:

 

ET9000

 

DVB: registering new adapter (dvb0)
DVB: registering adapter 0 frontend 0 (DVB-S2)...
DVB: registering adapter 0 frontend 1 (DVB-S2)...
input: front panel as /devices/virtual/input/input2
NET: Registered protocol family 10
dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
DVB: registering adapter 1 frontend 0 (Realtek DVB-T RTL2832)...
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_rtl2832u

root@et9x00:~# lsmod
Module                  Size  Used by
dvb_usb_rtl2832       426328  2 
dvb_usb                18026  1 dvb_usb_rtl2832
ipv6                  351430  12 
dvb                  5022440  31 
modloader2             32629  1 dvb
modloader              22281  0 
tpm                     6509  3 dvb,modloader2,modloader

 

VU+ UNO

 

dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
RTL2832U usb_init_bulk_setting : USB2.0 HIGH SPEED (480Mb/s)
RTL2832U check_tuner_type : ERROR Unknown tuner on board...
dvb-usb: no frontend was attached by 'RTL2832U DVB-T USB DEVICE'
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.1/usb2/2-1/input/input1
dvb-usb: schedule remote query interval to 287 msecs.
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_rtl2832u

root@vuuno:~# lsmod
Module                  Size  Used by
dvb_usb_rtl2832      391387  0
rt2800usb              13121  0
rt2800lib              43443  1 rt2800usb
rt2x00usb              10681  1 rt2800usb
rt2x00lib              40506  3 rt2800usb,rt2800lib,rt2x00usb
mac80211              208171  3 rt2800lib,rt2x00usb,rt2x00lib
ipv6                  346524  12
fpga_directc          57585  0
brcmfb                  1127  3
dvb_bcm7413          5059988  2 fpga_directc,brcmfb
procmk                  1397  2 fpga_directc,dvb_bcm7413

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=2838 Rev= 1.00
S:  Manufacturer=Realtek
S:  Product=RTL2838UHIDIR
S:  SerialNumber=00000013
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=dvb_usb_rtl2832u
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

root@vuuno:~# cat /proc/bus/nim_sockets
NIM Socket 0:
        Type: DVB-S2
        Name: Vuplus DVB-S NIM
        Frontend_Device: 0

 

Anyone have a idea why this is happening?

 

Thanks

[guirigui]

Hi,

Just to point out in the packet list, there are 2 entries, the good one wich install 2 packets and the wrong with one packet only..

May be it's the issue?

[Alex_NL]

I have the usb dvb RTL2832 with tuner R820T and I have problem to work with VU+ UNO. The same tuner in ET9000 works perfect.

 

How did you install it on the ET9000?
On my ET9500 it fails to work.

Edited by Lexzie, 26 July 2013 - 00:32.

[Gennar1]

The dvb_usb_rtl2832 driver on ET9000 has been updated recently, after I found a new version of the Realtek original driver with support for the r820t tuner.

The solution is to update the rtl2832 patch also for the VU+ kernels.

[Alex_NL]

How do I do that?

[wolfen]

is there a solution for this yet ?

i have the same problem.. vuduo with pli4