Thanks a lot, I shall change it.
So this script will now be executed automatically every time I reboot or restart the receiver or enigma2?
Posted 28 May 2015 - 17:31
Hallo it is possible to create a list of the possible providers which are supported For example, I TWEAK Sparql as provider. or is it a stupid question,
and it is possible that it works with at,I have absolutely no of understanding how at works, or what is needed, if it can be explained, please.
Posted 16 June 2015 - 05:55
So, is there a solution to get DVB-IPTV working on Openpli?
After years there is no solution, also not working solution for people who do not have knowledge with linux.
Again... I want this to work, however, but also after restart. Not UDP. RTP should work.
#SERVICE 1:0:19:283E:3FB:1:C00000:0:0:0:rtp%3a//@239.2.24.6%3a8208:arte HD
ET10000
Posted 16 June 2015 - 06:28
it doesn't work with 4097 over g-streamer.
this doens't work with openpli. I don't know why....
http://www.satnigmo....tech-receivers/
ET10000
Posted 16 June 2015 - 07:27
Yes, working with:
vlc
dvbviewer native (native without udpxy)
dreambox native (without http and udpxy)
Kodi (XBMC)
everywhrere I have also teletext in the stream.
everywhere working except openpli
I tried following combinations...
#SERVICE 1:0:19:132F:3EF:1:C00000:0:0:0:http%3a//127.0.0.1%3a4050/rtp/@239.2.24.1%3a8208/:ORF eins HD
Edited by mdshd, 16 June 2015 - 07:27.
ET10000
Posted 16 June 2015 - 07:38
Do you use udpxy from PLi feed? This one does not work for me, do not know why. Try the one from satnigmo. I have udp streams though
Posted 16 June 2015 - 07:50
as i said, the one from feed does not work for me! Satnigmo one is ok
Posted 17 June 2015 - 13:56
did you put the proper route to the in the IP table ?
I believe the udpxy comes automatically with the updates, but replace the file with the correct one of satnigmo.
- copy udpxy file in /usr/bin folder on ET10000, changed 0755 permission.
- copy udpxy file (start script) in /etc/init.d folder on ET10000, changed 0755 permission.
- via telnet : ln -s /etc/init.d/udpxy /etc/rc3.d/S99udpxy
(this shortcut now appears in the /etc/rc3.d/ directory)
- rebooted the receiver
- create in /etc/enigma2 "userbouquet.iptv.tv" file with the content you want
- add the correct route, such as route add -net 224.0.0.0 netmask 240.0.0.0 dev eth1 (adapt to your IP requirements)
ET10000, 4x DVB-S2, ET4000 client, Reelbox AVG 3x DVB-S2, 1x DVB-T.
Visiosat G3+ (28.2E-23.5E-19.2E-13E) 4x ALPS quad 0,2db.
Posted 31 July 2015 - 16:10
Hello,
I have the Xtrend ET10000 and I would like to thank you.
Before I have not any IPTV from mys DSL provider (Free in France)
Now it's OK at 50% with the app (gst-plugins-bad-mpegtsdemux_0.10.23.1+git12245+fb0d870-r5_mips32el find in your page).
Channels come very quickly now (SD and HD)
The problem is now with the sound. Sometime sound is good and after changing channel, no more sound if I return on the last channel.
I try to change the libgstmpegdemux.so but the problem is the same. Sound is OK or NO on the same channel.
I try openatv and with the new gstreamer, there is no problem. All is OK.
But ... I love and prefer OPENPLI who is the best for me... I come back every time with OpenPli who have not the new gstreamer (grrr)
So that is my experience with IPTV on the fabulous ET10000.
cheers
Pat
TNT/Sat : VU+ Duo 4K SE - Home cinema : Onkyo TX NR686 | Air Gay Radio
Posted 5 August 2015 - 04:24
did you put the proper route to the in the IP table ?
I believe the udpxy comes automatically with the updates, but replace the file with the correct one of satnigmo.
- copy udpxy file in /usr/bin folder on ET10000, changed 0755 permission.
- copy udpxy file (start script) in /etc/init.d folder on ET10000, changed 0755 permission.
- via telnet : ln -s /etc/init.d/udpxy /etc/rc3.d/S99udpxy
(this shortcut now appears in the /etc/rc3.d/ directory)
- rebooted the receiver
- create in /etc/enigma2 "userbouquet.iptv.tv" file with the content you want
- add the correct route, such as route add -net 224.0.0.0 netmask 240.0.0.0 dev eth1 (adapt to your IP requirements)
Hello,
could somebody please make a plugin for multicast with all this things and put it on the feed so everybody can install it easily. For somebody who have skills, this is 5 minutes job.
I don't know what does it mean? Where to add this line? "- add the correct route, such as route add -net 224.0.0.0 netmask 240.0.0.0 dev eth1 (adapt to your IP requirements)"
ET10000
Posted 5 August 2015 - 05:02
So, ok i puted it over telnet
"route add -net 224.0.0.0 netmask 240.0.0.0 dev eth1" but i don't know what does it mean, should i change this number s to something else?
I also installed this mpegts demux. Nothing happens. Nothing. Made all as describved here and on satnigmo. No Chance.
nothing happens. it doesn't work for me on ET10000. I have made all described above. I can not believe it. With openpli over 2 years i can not have multicast with this f. hack. On all other receivers softwares multicast works natively. unbelieveable.
ET10000
Posted 1 September 2015 - 12:37
Sorry for the late reply.
What if via telnet you type the following, what is the reply ?
if ps | grep udpxy | grep -v grep; then echo 'udpxy is running OK'; else echo 'udpxy is NOT running'; fi
This should tell you if udpxy is running
route add -net 224.0.0.0 netmask 240.0.0.0 dev eth1
This should make sure that all request of multicast streams are made to the eth1 interface, the 1Gb network interface. Assuming that you have connected the network cable to this interface.
route -n
This should show the correct route
ET10000, 4x DVB-S2, ET4000 client, Reelbox AVG 3x DVB-S2, 1x DVB-T.
Visiosat G3+ (28.2E-23.5E-19.2E-13E) 4x ALPS quad 0,2db.
Posted 26 September 2015 - 22:08
Is there someone who can get this this to work. I think the udpxy cannot be started. There are people on this forum, who can make this working in 5 minutes forever. Why it is a problem to make a plugin which install all at once. Start script and udpxy so it can be downloaded on the feed over extensions or system plugins.
ET10000
Posted 27 September 2015 - 08:44
Even if you get udpxy working, there's no guarantee it's ever going to work. You settopbox is simply not designed for IPtv, there may be codecs and containers used that the STB doesn't support, unsupported encryptions, etc, so we don't really support it.
* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.
Posted 27 September 2015 - 15:03
ET10000
0 members, 1 guests, 0 anonymous users