Check the dish?
Would it help despite other 28.2E tuned OK?
VU+ Solo2 no Freesat channels on Astra 28.2E
Started by voyo, 14 Mar 2015 21:38
25 replies to this topic
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #21
-
- Member
- 21 posts
0
Neutral
Posted 19 March 2015 - 20:29
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #22
-
- PLi® Core member
- 68,519 posts
+1,735
Excellent
Posted 19 March 2015 - 20:29
Do you have any other transponder on 28.2 Vertical that does have reception?
It could be a broken LNB, a broken DiseqC switch, or an incorrect DiseqC config. Or a mis-aligned dish or LNB.
The fact that you can receive one transponder doesn't guarantee reception on all transponders.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #23
-
- Member
- 21 posts
0
Neutral
Posted 20 March 2015 - 08:00
Hi,
Just checked a few V transponders on 28.2 - got many of them locking OK.
However, the lowest frequency predefined transponder which locks at all on 28.2 is 11720 H.
All predefined transponders frequencies below 11720 H show always SNR 0%.
Could this indicate a fault of LNB?
Should I change modulation on predefined ones? But I have many SKY channels visible.....
Thanks.
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #24
-
- Senior Member
- 985 posts
+20
Neutral
Posted 20 March 2015 - 08:23
Switch the power off on receiver (take it from the mains) before disconnecting the coax cables!
Can you test with the receiver directly by bypassing the DiSEqC switch, connecting the the cable coming from the 28.2°E LNB directly to the receiver?
If the switch is outside, and easy accessible, you could do this by disconnecting the cable going inside and the one from the LNB.
And temporary connect these 2 cables with an special F-connector (female/female).
If you get the same result: get assistance by someone who is used to install/check dish:
Pole alignment: 360° plumb (check with level), Tensioning the bolts, if these did become loose could even solve your problem.
Cable from that LNB to switch, connectors (oxidation, ...)
Sf8HD, sf8008, OpenPli 9.0, fixed lnb 28.2E, 19.2E
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #25
-
- PLi® Core member
- 46,951 posts
+541
Excellent
Posted 20 March 2015 - 10:05
Hi,
Just checked a few V transponders on 28.2 - got many of them locking OK.
However, the lowest frequency predefined transponder which locks at all on 28.2 is 11720 H.
All predefined transponders frequencies below 11720 H show always SNR 0%.
Could this indicate a fault of LNB?
Should I change modulation on predefined ones? But I have many SKY channels visible.....
Thanks.
This is exactly the "takeover" frequency between low- and high bands.
This means either the tuner or the lnb(s) is/are defective, more probably the lnb(s).
* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.
Re: VU+ Solo2 no Freesat channels on Astra 28.2E #26
-
- Member
- 21 posts
0
Neutral
Posted 21 March 2015 - 15:01
Hi there,
My other dish for Hot Bird works fine on all frequencies (low and high bands) so the satellite box is OK.
Both satellites are connected via an external switch.
It must be a faulty LNB on my Astra 28.2!
Will replace it then.
Many thanks for your help.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
