Forums

Dear PLiers,

• From running openpli-3.0-20120916 system (Kernel 3.4.3) I started Setup/Sorftware Update. It looked promissing, but the box failed to start after reboot (only xtrend logo)
• Than I tried to flash current OpenPLi-4.0-beta-et9x00-20140422_usb.zip, from USB stick, but same result: Flashing successful, but box simply hangs at boot: Only Xtrend logo on the screen.
• Than I flashed back the old openpli-3.0-20120916, repeated the setup and the box is running again.

So how do I update correctly?

Do I have to prepare or do anything else before flashing/updating? The wiki is not too helpfull on this question.

Any ideas, suggestions?

Thomas

init 4
enigma2

Sounds like an old bootloader?

Thanks a lot for your support! I did update the bootloader once, but I can't find the image/zip.

When booting the RS232 says:

BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Sat Dec 10 11:20:16 WEST 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.

I only find the date of the current bootloader (2011-10-21), but no version is stated..

www.et-view-support.com  seems down..

Should I flash 4.0 again and check with telnet (init 4, enigma2)?

What is shown on the display when you boot the box? Et9200 or et9x00?

ET9X00 is displayed

Battery dead, tpm dead. The same old story from Xtrend. When we will have those promised drivers that no longer check tpm? I have four dead boxes waiting for this (no I will not pay 60 euros for a replacement tpm board - xtrend has to deliver a free fix for this).

Try first this old bootloader than the newer one. (the file i have renamed to et9x00)

Battery dead, tpm dead. [..] I have four dead boxes waiting for this[..]

The box is not dead. When I flash the old openpli-3.0-20120916 the box is booting nicely.. (as I've written in my first post).

Try first this old bootloader than the newer one. (the file i have renamed to et9x00)

As there is always some risk involved, when flashing a bootloader, I'm really wondering, what switching back and forth boot loader version, could cause/fix for updating to openPLi 4.0?

Thomas

Bootlog while Flashing:

BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Sat Dec 10 11:20:16 WEST 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.

start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 256MB
CPU speed:     405MHz
Memory Config: 64-bit UMA
Device Tech:   1Gb
Total memory:  512MB
Boot Device:   NOR
Total flash:   4MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.
Set default GPIO...

USB: New device connected to bus 1 hub 1 port 1/esc/[J
USB: Resetting device on bus 1 port 1/esc/[J USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub

USB: New device connected to bus 1 hub 2 port 1/esc/[J
USB: Resetting device on bus 1 port 1/esc/[J USB: Locating Class 08 Vendor 1307 Product 0163: Mass-Storage Device

USBMASS: Unit 0 connected/esc/[J
USB: New device connected to bus 1 hub 2 port 2/esc/[J
USB: Resetting device on bus 1 port 2/esc/[J USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device  (00:00:00:00:00:00)
found image:
openpli-4-20140422
flash image?  (OK//CANCEL)
flashing...
Reading usbdisk0:et9x00//kernel.bin: Done. 4331027 bytes read
Programming...
offset=0 copysize=4331027
done. 4331027 bytes written
flashing...
Reading usbdisk0:et9x00//rootfs.bin: Done. 55443456 bytes read
offset: 00000000   size: 0FA00000
Force erasing...
Erasing flash...Programming...
offset=0 copysize=55443456
done. 55443456 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************

Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: !!!!! UNC read error occurred, while reading from NAND flash -1
0x80001000//8034432 !!!!! UNC read error occurred, while reading from NAND flash -1
0x807aa880//137360 Entry address is 0x805e66c0
TP1 Entry Address at 0x80000ffc = 805e66c0
Starting program at 0x805e66c0

**Exception 32: EPC=8076B590, Cause=00008028, VAddr=00000000
                RA=805E66E0, PRID=0002A044

        0  ($00) = 00000000     AT ($01) = 807B0000
        v0 ($02) = 00010000     v1 ($03) = 00000040
        a0 ($04) = 87055870     a1 ($05) = 00000000
        a2 ($06) = 8700C364     a3 ($07) = 43464531
        t0 ($08) = 00000000     t1 ($09) = 807CC10C
        t2 ($10) = FFFFFFC0     t3 ($11) = 87098FE4
        t4 ($12) = 00000001     t5 ($13) = 870A1426
        t6 ($14) = 8700C9CC     t7 ($15) = 3EA95587
        s0 ($16) = 8700C2F0     s1 ($17) = 87010000
        s2 ($18) = 00000000     s3 ($19) = 8704DF30
        s4 ($20) = 8714FD88     s5 ($21) = 87098EE8
        s6 ($22) = 8714FD30     s7 ($23) = 87016828
        t8 ($24) = 00000101     t9 ($25) = 8709901C
        k0 ($26) = 00000000     k1 ($27) = 00000000
        gp ($28) = 80716000     sp ($29) = 80717F20
        fp ($30) = 87032790     ra ($31) = 805E66E0


*** Waiting for system reset ***
 

Strange enough with openhdf-et9x00-940-20140422_usb.zip (http://v4.hdfreaks.c...php?dir=et9x00/), the box is booting find, even if the same error happens:

*** Waiting for system reset ***
/nul//nul/
BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000006
WC1=FFFFFFEB
RC2=00000019
WC2=0000003A
RC3=0000000F
WC3=FFFFFFEA
RC4=0000000F
WC4=00000038
NWC=00000011
RC5=00000006
WC5=00000011
RC6=00000019
WC6=00000011
NRC=0000000F
RW=00000014
WW=0000004F
G=00000000 R=0000000F W=00000011
BL=00000000
RC1=00000002
RC2=00000015

BL=00000001
RC1=00000005
RC2=0000001B

BL=00000002
RC1=00000007
RC2=00000016

BL=00000003
RC1=00000007
RC2=0000001A

BL=00000004
RC1=00000005
RC2=0000001A

BL=00000005
RC1=00000006
RC2=0000001F

BL=00000006
RC1=00000003
RC2=00000019

BL=00000007
RC1=00000005
RC2=00000019
SCfC3
COPY CODE
COMPARE CODE
4567

BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Sat Dec 10 11:20:16 WEST 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.

start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 256MB
CPU speed:     405MHz
Memory Config: 64-bit UMA
Device Tech:   1Gb
Total memory:  512MB
Boot Device:   NOR
Total flash:   4MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.
Set default GPIO...

USB: New device connected to bus 1 hub 1 port 1/esc/[J
USB: Resetting device on bus 1 port 1/esc/[J USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub

USB: New device connected to bus 1 hub 2 port 1/esc/[J
USB: Resetting device on bus 1 port 1/esc/[J USB: Locating Class 08 Vendor 1307 Product 0163: Mass-Storage Device

USBMASS: Unit 0 connected/esc/[J
USB: New device connected to bus 1 hub 2 port 2/esc/[J
USB: Resetting device on bus 1 port 2/esc/[J USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device  (00:00:00:00:00:00)
found image:
openhdf-4.0.940
flash image?  (OK//CANCEL)
flashing...
Reading usbdisk0:et9x00//kernel.bin: Done. 4345676 bytes read
Programming...
offset=0 copysize=4345676
done. 4345676 bytes written
flashing...
Reading usbdisk0:et9x00//rootfs.bin: Done. 84017152 bytes read
offset: 00000000   size: 0FA00000
Force erasing...
Erasing flash...Programming...
offset=0 copysize=84017152
done. 84017152 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************

Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: !!!!! UNC read error occurred, while reading from NAND flash -1
0x80001000//8067200 0x807b2880//163984 Entry address is 0x805f07f0
TP1 Entry Address at 0x80000ffc = 805f07f0
Starting program at 0x805f07f0

Linux version 3.8.7 (jenkins@puck1170.server4you.de) (gcc version 4.8.2 (GCC) ) #1 SMP Thu Mar 13 02:02:24 CET 2014
Fetching vars from bootloader... found 10 vars.
Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=1 moca=0
         sata=1 docsis=0 pci=1 pcie=0 smp=1 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
 memory: 10000000 @ 20000000 (usable)
bmem: adding 216 MB RESERVED region at 40 MB (0x0d800000@0x02800000)
Zone ranges:
  Normal   [mem 0x00000000-0x2fffffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x0fffffff]
  node   0: [mem 0x20000000-0x2fffffff]
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
PERCPU: Embedded 7 pages//cpu @81407000 s6272 r8192 d14208 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line:  bmem=216M ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs console=ttyS0,115200n8
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
__ex_table already sorted, skipping sort
Memory: 290476k//524288k available (6121k kernel code, 233812k reserved, 1510k data, 300k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:160
Detected MIPS clock frequency: 405 MHz (202.500 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 401.40 BogoMIPS (lpj=200704)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
SMP: CPU1 is running
Brought up 2 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
USB0: power enable is active low; overcurrent is active low
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
pci_bus 0000:00: root bus resource [io  0x0400-0x83ff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
pci_bus 0000:01: root bus resource [io  0x8400-0x87ff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource upg
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Installing knfsd (copyright © 1996 okir@monad.swb.de).
fuse init (API version 7.20)
msgmni has been set to 567
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250//16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10//100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:05:40:24)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS//2 mouse device common for all mice
i2c //dev entries driver
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Bluetooth: HIDP socket layer initialized
ata1.00: ATA-8: FUJITSU MHW2120BH, 00000012, max UDMA//100
Key type dns_resolver registered
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecda1095
After: NandSelect=50000200, nandConfig=16152300
Block size=00020000, erase shift=17
NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec da Samsung K9F2G08U0A 256MB on CS1
 

@malakudi

Is your statement Battery(TPM) dead refering to:

UNC read error occurred, while reading from NAND flash -1
0x80001000//8067200 0x807b2880//163984 Entry address is 0x805f07f0
TP1 Entry Address

What might this error mean to me?

Any idea?

Thomas

If your box boot with any older image, my statement is invalid. If the tpm board is dead, no driver can be loaded, older or newer.

I am not quite the expert on this, but this suggests problems with the flash memory? Maybe the older image is smaller and doesn't reach the bad section?

Thank you all for your support, but I guess I'll stick to the HDF-Team-Image. as it runs quite good. They did (and hopefully do) a very good job, IMHO.

Thomas