Jump to content


Photo

CCCam 232 or 230 and OpenPLI 6.2


  • Please log in to reply
8 replies to this topic

#1 waara

  • Member
  • 9 posts

0
Neutral

Posted 14 May 2018 - 17:52

The combo is not working. I'm using OpenPli 6.1 at the moment without any problems. Yesterday I made a backup of my 6.1 installation, and after this tried to install 6.2. The installation went well, but I immedeately noticed that the only softcam installed was Mgcamd. I tried then to install CCCam 230. I got a lot of errors, and basically, the installation didn't work.

I tried installing 232 after this. The same problems.

 

I had to move back to OpenPli 6.1.

 

Anyone had the same problems? How do I fix this?

 

I have a VU+ Duo.

 

Best regards

 

Roger


Edited by waara, 14 May 2018 - 17:54.


Re: CCCam 232 or 230 and OpenPLI 6.2 #2 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 14 May 2018 - 19:56

The problem is that quite a few of the oldest boxes we support (ET 4000/5000/9000, VU+ Uno/Solo/Duo, XP1000, etc) only have 128MB flash memory.

 

This is slowly becoming quite tight. I just flashed an XP1000 with 6.1-release (it is the only box with 128MB that I have), and after a flash, configuration and a scan, but before installing anything, I only have 33MB free anymore. Which means that you need to be very careful what you choose to install. This is also the reason an upgrade from 6.1-release to 6.2-release (which updates hunderds of packages) will fail.

 

We're looking into how we can reduce the size, but don't expect any miracles.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: CCCam 232 or 230 and OpenPLI 6.2 #3 waara

  • Member
  • 9 posts

0
Neutral

Posted 20 May 2018 - 12:28

The problem is that quite a few of the oldest boxes we support (ET 4000/5000/9000, VU+ Uno/Solo/Duo, XP1000, etc) only have 128MB flash memory.

 

This is slowly becoming quite tight. I just flashed an XP1000 with 6.1-release (it is the only box with 128MB that I have), and after a flash, configuration and a scan, but before installing anything, I only have 33MB free anymore. Which means that you need to be very careful what you choose to install. This is also the reason an upgrade from 6.1-release to 6.2-release (which updates hunderds of packages) will fail.

 

We're looking into how we can reduce the size, but don't expect any miracles.

Thanks for your reply. When I read your reply i remembered seeing some note about "Not enough space" on the screen.. Is there a easy way to clean up the installation? Besides going in to the menus and removing skins, plugins aso?
Otherwise 6.1 seems to be "end of the road" for my old VU+ Duo.. Sad, but inevitable i guess..

 

Does newer versions of VU+ Duo have more internal memory?


Edited by waara, 20 May 2018 - 12:29.


Re: CCCam 232 or 230 and OpenPLI 6.2 #4 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 21 May 2018 - 11:17

We're looking into it at the moment, so don't throw it away just yet...


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: CCCam 232 or 230 and OpenPLI 6.2 #5 waara

  • Member
  • 9 posts

0
Neutral

Posted 23 May 2018 - 21:12

We're looking into it at the moment, so don't throw it away just yet...

 

I'll rest my case until further noticed.. :) Thanks for taking time!

 

R



Re: CCCam 232 or 230 and OpenPLI 6.2 #6 waara

  • Member
  • 9 posts

0
Neutral

Posted 9 October 2018 - 16:04

Any news on this?



Re: CCCam 232 or 230 and OpenPLI 6.2 #7 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 10 October 2018 - 10:13

There isn't much you can do about it.

 

Flash a new version, and try to limit upgrades. The only thing that takes up a bit of space and can be removed is Samba, but you'll lose CIFS access to local storage. OpenPLi in general doesn't preinstall anything that isn't really needed, so there isn't much else you can remove. There are no skins other than the default, or drivers other than the kernel ones. By default only a few plugins are installed, but you can't do without them, and they hardly take up any space.

 

With some hacking you could start from NFS, and there is also something called flash extended which uses some local storage device to extend the space in flash, but not sure that works on all boxes...


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: CCCam 232 or 230 and OpenPLI 6.2 #8 Владимир

  • New Member
  • 1 posts

0
Neutral

Posted 14 November 2018 - 06:48

Лично я пользуюсь  2.32  или 2.31.  2.32-Pli6.2  , а на pli 6.1-pli 4.0--2.31,  все беру  на Satvenus Panel-все работает на ура!  sviridov55.



Re: CCCam 232 or 230 and OpenPLI 6.2 #9 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,380 posts

+393
Excellent

Posted 14 November 2018 - 10:13

Please post only in English, German or Dutch.

Пожалуйста, опубликуйте только на немецком, английском или голландском языках. ;)
хорошо, что мы смогли сделать так счастливым.

Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users