Springen naar inhoud


Foto

Autotimer simulate optie werkt niet correct


  • Please log in to reply
Er zijn 5 reacties in dit onderwerp

#1 _HarmeN

  • Senior Member
  • 765 berichten

+4
Neutral

Geplaatst op 31 augustus 2018 - 09:07

Wanner ik via de webinterface een simulatie doe van de autotimers komen er maar 2 resultaten naar voren, terwijl er meerdere autotimers (juist) zijn gemaakt.

Een maat van me heeft dit probleem ook, hier worden al maanden geen timers meer getoond in de simulatie.


Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC :: ZIGGO

Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC + 1x DVB-S2 FBC :: ZIGGO

 


Re: Autotimer simulate optie werkt niet correct #2 40H3X

  • Forum Moderator
    PLi® Contributor
  • 5782 berichten

+186
Excellent

Geplaatst op 31 augustus 2018 - 09:17

Misschien is het beter om dit te melden bij de "Maintainer" vd plugin?


Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K  - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport

---------------------------------------------------------------------------------------------------------------------------------------

Remember: Upvote with the rep_up.png button for any user/post you find to be helpful, informative, or deserving of recognition!

---------------------------------------------------------------------------------------------------------------------------------------

Many answers to your question can be found in our new and improved wiki

Note: I do not provide support via PM !.


Re: Autotimer simulate optie werkt niet correct #3 _HarmeN

  • Senior Member
  • 765 berichten

+4
Neutral

Geplaatst op 31 augustus 2018 - 17:56

Ok en waar doe ik dat ?

Kunnen meer mensen dit bevestigen ?

Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC :: ZIGGO

Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC + 1x DVB-S2 FBC :: ZIGGO

 


Re: Autotimer simulate optie werkt niet correct #4 WanWizard

  • PLi® Core member
  • 68309 berichten

+1719
Excellent

Geplaatst op 31 augustus 2018 - 18:14

Ik zie momenteel het omgekeerde: de simulatie komt met een timer die de laatste autotimer run niet heeft aangemaakt.

 

Kan het zijn dat zaken als duplikaat detectie en zo niet meeloopt in de simulatie?


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Autotimer simulate optie werkt niet correct #5 _HarmeN

  • Senior Member
  • 765 berichten

+4
Neutral

Geplaatst op 7 september 2018 - 18:39

Hmm als ik mn al geplande timerlijst leegmaak en dan simuleer dan staat alles er wel. Het lijkt er dus op dat hij alleen iets laat zien wat nog niet al getimerd is.

Volgens mij was dit eerder niet zo.


Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC :: ZIGGO

Vu+ Ultimo 4K (OpenPLI-9.0) :: 1x DVB-C FBC + 1x DVB-S2 FBC :: ZIGGO

 


Re: Autotimer simulate optie werkt niet correct #6 WanWizard

  • PLi® Core member
  • 68309 berichten

+1719
Excellent

Geplaatst op 8 september 2018 - 16:29

Dan zul je in discussie met de auteur moeten.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.



1 gebruiker(s) lezen dit onderwerp

0 leden, 1 bezoekers, 0 anonieme gebruikers