Gigablue UHD Quad 4K flash image
aage 13 Sep 2018
Used Image v6.2 20180911 on a USB stick after 15 sec. it finish and in display was text selekt language?.no picture on tv.
On USB stick are folders gigablue - quad4k ,in qua4k are some bin files,and a tar. file rootfs.tar.bz2
Should rootfs.tar.bz2 be decompressed before installed on the USB ?
Regards Aage
WanWizard 13 Sep 2018
After you flash an image, the setup wizard starts so you can configure the image. And the first question is "what language do you want the image to be in".
How would you expect the box to produce a picture without any configuration?
Pr2 13 Sep 2018
Hi,
From what you describe your Gigablue is properly flashed, I guess that you read the message "which language ..." on the front display of your Gigablue.
Since it is a first installation you need to turn on yourself the TV ON, the select the correct HDMI input to see the message on your TV screen.
After you have finished the installation Wizard, you can go into the HDMI-CEC setup screen and there you can activate and configure it to have your TV turned on and select the right HDMI entry.
But after a flash you always need to turn on the TV on the right entry yourself with your TV Remote Control.
Pr2
aage 14 Sep 2018
Hi,
From what you describe your Gigablue is properly flashed, I guess that you read the message "which language ..." on the front display of your Gigablue.
Since it is a first installation you need to turn on yourself the TV ON, the select the correct HDMI input to see the message on your TV screen.
After you have finished the installation Wizard, you can go into the HDMI-CEC setup screen and there you can activate and configure it to have your TV turned on and select the right HDMI entry.
But after a flash you always need to turn on the TV on the right entry yourself with your TV Remote Control.
Pr2
Thanks for the answer.
I have change to the factory image 20170731.
Here there are no problems,the boot logo and the wizard came up on the tv screen,
now you can choose language HDMI output and so on.
(its very difficult to navigate on the tuner display)
Do you know how to change the color of numbers and letters.
In the channals and service list the letters and numbers are blue on black background,
very difficult to read.
Best regards.
Aage
Pr2 14 Sep 2018
Hi,
Strange the color you refer to doesn't seems to be the one used by OpenPLi by default.
Personally I use the skin: PLi-FullNightHD
Pr2
arn354 14 Sep 2018
The issue is that his tv is not showing the resolution which is used on first boot. I guess he owns a Hisense model?
Try another HDMI-Port onTV. Check the tv manual and tv settings.
Edited by arn354, 14 September 2018 - 22:00.
aage 16 Sep 2018
Hi,
Strange the color you refer to doesn't seems to be the one used by OpenPLi by default.
Personally I use the skin: PLi-FullNightHD
Pr2
It is in image, factory 20170730 v1708 Team Blue.
regards Aage
aage 16 Sep 2018
The issue is that his tv is not showing the resolution which is used on first boot. I guess he owns a Hisense model?
Try another HDMI-Port onTV. Check the tv manual and tv settings.
The TV has four HDMI input.
I have two recivers with OpenPli v6.2 latest running in port 1-2.
In port 3 i have a DVD player.
These devices are running without failor.
In port 4 Gigablue.
If i used image factory 20170731 v1708 Team GigaBlue there is no problems.
If i used image Open Vix v5.1 latest there is no problems.
When using Team GigaBlue v6.1 lates,and OpenPli v6.2 latest i got troble.
With Open Pli v6.2 latest.
Reciver Display,when booting the first 5 sec.Team Blue logo
after 3 sec.the same logo on the tv.
then display gray
on tv no signal
then on display 1 sec. logo Open Pli v6.2
tv no signal
then on display 7 sec.logo Open Pli v6.2
the same on tv
then on display grafbar booting
on tv no signal
after booting complete,the display show the startup wizard.
The tv screen change to gray.
Best regards
Aage