OpenPLi 7.1 Release Candidate
WanWizard 15 May 2019
As of today, OpenPLi 7.1 Release Candidate is available for download and installation.
The release candidate is a pre-release test version, and will be publicly available for a short time only. Only install this version when you have backup, if you intend to test this version, and to provide feedback here. At this point we can not guarantee it is free from (serious) errors.
Once testing is over, any issues found are addressed and OpenPLi 7.1 Release has been made public, we will remove the release candidate images and their feeds. You will no longer be able to update, and need to flash the official release image.
We therefore suggest end-users should not to install this version, but wait for the official release instead.
gigabite 15 May 2019
wanwizard thanks for the info I have tested h9 combo and the box does not flash
gigabite 15 May 2019
I downloaded the image
in the folder I changed the file force_h9combo.txt inserted into usb-stick and not flashing
I have used 3 usb-sticks
littlesat 15 May 2019
You first need to flash the smaller recover image. You put this image unzipped on the USB stick. Then you boot the box while holding on/or button on the remote. Then the emmc image should be moved to the USB as is as zip file in the root and you should be able to flash the image from the USB and maybe also (I did not check if this already worked) via the online install feature within the recovery mode.
While flashing the recovery image you need to hold the reset button while powering the box on via the white button on the back... you see boot and than flash...
Edited by littlesat, 15 May 2019 - 11:41.
Quark82 15 May 2019
I have the same flash problem on the Mutant HD60.
I copy the unzipped folder hd60 and the force_hd60.txt to the usb stick.
The flashing process is starting, red LED is blinking for 1 minute.
reboot
And it starts the old openpli-7.0 Image was I flashed before.
Do you have a mini how-to for flashing the openpli-7.1-rc-hd60-20190515 image?
littlesat 15 May 2019
For the HD60 it is the same... Flash recovery image first...
Edited by littlesat, 15 May 2019 - 11:49.
WanWizard 15 May 2019
Afaik, the same applies to the HD60.
The manufacturers of multiboot capable hardware seem to move to a system where you can flash images from the bootloader. Which means you first have to update the bootloader with this recovery image.
40H3X 15 May 2019
@Littlesat flashing the recovery_emmc.zip file? Wasn't that only needed to have multiboot?
littlesat 15 May 2019
As far I understand the box needs to be 'prepared' alias 'formatted and as far I know this means you need to flash this one first...it adds a recovery mode to the box and from this recovery mode you can install OpenPLi and other images online -or- via the (as zip) the media (USB).
This is the last flash with full startup with USB stick the box actually needed... from than you can update via the recovery boot menu you always get when holding a button on a remote while powering ON the box... (unless the recovery image will be updated).
Edited by littlesat, 15 May 2019 - 11:59.
Frenske 15 May 2019
littlesat 15 May 2019
Here I was also not able to flash a 'standard' image... it simply did not start flashing...
it could be my fault... if so please let us know
Edited by littlesat, 15 May 2019 - 12:52.
littlesat 15 May 2019
Did you hold the reset button at the back of the receiver while powering it on?
gigabite 15 May 2019
I unzipped the emmc file I inserted usb in the box and it does not display the file in usb
online flash is perfect
http://i65.tinypic.com/2hs4rr7.jpg
http://i66.tinypic.com/2w4hdg8.jpg
WanWizard 15 May 2019
From what I understand you don't need to extract the zip when you want to flash via the bootloader menu (if I understood Littlesat correctly)?
morpheus1969 15 May 2019
hi friends are you speak about multiboot?
it is possible to try flash normally about pli7.1?
thx
gigabite 15 May 2019
with this mode it works
Attached Files
WanWizard 15 May 2019
I unzipped the emmc file I inserted usb in the box and it does not display the file in use
Because you did this. The bootloader flash menu needs zip files I understand.
gigabite 15 May 2019
I installed the recovery file and everything is ok
I added the emmc file in USB stick and it is not detected
I installed the image online and everything is ok
the usb stick file is ok only via online flash