Hi everyone, I have a problem with the zgemma h9 combo, but I don't understand if it's an error or an openpli image problem. Let me explain better, I mounted on the deco the openpli-7.2-rc-h9combo dated 04.11.2019 but I can't find in the menu, the Hard disk item to be able to format the microsd.
OpenPLi 7.2 problem on zgemma h9 Combo
Started by byanonimo, 04 Nov 2019 23:20
57 replies to this topic
Re: OpenPLi 7.2 problem on zgemma h9 Combo #2
-
- Forum Moderator
PLi® Core member - 27,393 posts
+394
Excellent
Posted 4 November 2019 - 23:32
You might have choose for the expertmode. Menu - setup - system - expert setup - user settings and change this to expert.
At least that’s what I hope.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. 
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #3
-
- Senior Member
- 27 posts
0
Neutral
Posted 4 November 2019 - 23:48
Already tried both in expert mode and in advanced mode, but nothing
Re: OpenPLi 7.2 problem on zgemma h9 Combo #4
-
- Senior Member
- 2,338 posts
+33
Good
Posted 4 November 2019 - 23:59
Format the micro-sd in a computer as ext4 and then insert it into the H9.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #5
-
- Senior Member
- 27 posts
0
Neutral
Posted 5 November 2019 - 13:46
Also tried this but nothing, I think it is a problem of the image, because if I enter the decoder by ftp, the microsd is seen without problems. Virtually the image does not show me the menu to manage Hard Disk
Re: OpenPLi 7.2 problem on zgemma h9 Combo #6
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 13:49
What exactly do you want to manage?
I can imagine that the menu item isn't shown because an SD card is not a HDD (and only hdd's are perhaps supported)?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #7
-
- Senior Member
- 5,461 posts
+114
Excellent
Posted 5 November 2019 - 14:13
I have a similar issue with a Mut@nt HD60. The OpenPli 7.1 does not see the TF card at all (hence no menu-item to set it up).. It probably only searches for USB and internal HDD's... It's not just OpenPli... Other images don't detect them either.... That's the advantage of MultiBoot.. You can try every image you like...
Met één been in het graf..... Helaas
Re: OpenPLi 7.2 problem on zgemma h9 Combo #8
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 14:18
I expected that, so it needs to be looked at.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #9
-
- Senior Member
- 444 posts
+15
Neutral
Posted 5 November 2019 - 15:06
I have a similar issue with a Mut@nt HD60. The OpenPli 7.1 does not see the TF card at all (hence no menu-item to set it up).. It probably only searches for USB and internal HDD's... It's not just OpenPli... Other images don't detect them either.... That's the advantage of MultiBoot.. You can try every image you like...
Well you obviously haven't tried all the images!! - the issue is that it comes up as mmcblk1p...(so has to be handled differently) a zgemma favourite trick (the H9 uses mmcblk0.. ) for a SD card
Edited by twol, 5 November 2019 - 15:07.
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
.........DVB-S2X into 90cm dish (27.5W)
Octagon sf8008, AX HD61, Edision Osmio 4K+, Zgemma H9Combo using Legacy ports on multiswitches
Zgemma H9twin & Zgemma H9 C/S mode into Giga4K
Re: OpenPLi 7.2 problem on zgemma h9 Combo #10
-
- Senior Member
- 5,461 posts
+114
Excellent
Posted 5 November 2019 - 15:20
Off course I haven't tried every images.. Only the once of interest. But for completeness I have tried a few..
OpenSPA.... No luck installing
OpenHDF 6.4 ... Works...
OpenVision 7.3 r53 .... Works
OpenSPA.... No luck installing
OpenHDF 6.4 ... Works...
OpenVision 7.3 r53 .... Works
Met één been in het graf..... Helaas
Re: OpenPLi 7.2 problem on zgemma h9 Combo #11
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 15:47
The challenge will be to make sure the correct device is shown in all cases, without the risk of end-users formatting the internal eMMC and brick the box. And this without "if h9 then elseif hd60..." hardcoded hacks...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #12
-
- Senior Member
- 444 posts
+15
Neutral
Posted 5 November 2019 - 15:54
The challenge will be to make sure the correct device is shown in all cases, without the risk of end-users formatting the internal eMMC and brick the box. And this without "if h9 then elseif hd60..." hardcoded hacks...
Well the internal eMMC is mmc0blk and the SD is mmc1blk
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
.........DVB-S2X into 90cm dish (27.5W)
Octagon sf8008, AX HD61, Edision Osmio 4K+, Zgemma H9Combo using Legacy ports on multiswitches
Zgemma H9twin & Zgemma H9 C/S mode into Giga4K
Re: OpenPLi 7.2 problem on zgemma h9 Combo #13
-
- PLi® Core member
- 56,268 posts
+691
Excellent
Posted 5 November 2019 - 16:30
Then it is still an challenge...
And this without "if h9 then elseif hd60..." hardcoded hacks...
Edited by littlesat, 5 November 2019 - 16:32.
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Re: OpenPLi 7.2 problem on zgemma h9 Combo #14
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 16:30
Is that the same on all boxes with multiple eMMC devices?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #15
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 16:31
Then it is still an challenge...
What probably needs to happen is change "backlist hardcoded all eMMC devices" to "blacklist the boot device".
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #16
-
- PLi® Core member
- 7,185 posts
+323
Excellent
Posted 5 November 2019 - 17:05
Well the internal eMMC is mmc0blk and the SD is mmc1blk
The challenge will be to make sure the correct device is shown in all cases, without the risk of end-users formatting the internal eMMC and brick the box. And this without "if h9 then elseif hd60..." hardcoded hacks...
Not always!
Normal rootfs, kernel partitions on Edision boxes are located on mmcblk1. At least for mio4k(+)
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04
Re: OpenPLi 7.2 problem on zgemma h9 Combo #17
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 17:19
Thought so. So it might be safer to find the boot device, and exclude that. That should work in all cases.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #18
-
- PLi® Core member
- 7,185 posts
+323
Excellent
Posted 5 November 2019 - 17:33
In most cases, but not all. In some boxes it's possible to boot from SD card. SD card is mmcblk1 or mmcblk2 or sda. I such case I would say you still shouldn't be able to format/partition mmcblk0 (if that's your internal flash memory).
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04
Re: OpenPLi 7.2 problem on zgemma h9 Combo #19
-
- PLi® Core member
- 68,586 posts
+1,738
Excellent
Posted 5 November 2019 - 17:43
Looks like all eMMC's are blacklisted here: https://github.com/O...arddisk.py#L613
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: OpenPLi 7.2 problem on zgemma h9 Combo #20
-
- PLi® Core member
- 56,268 posts
+691
Excellent
Posted 5 November 2019 - 17:52
Yep all emmc is blacklisted on specific boxes... how do we determine which of them is the boot (partition)? Only when we can determine this is a proper way we can safely allow emmcs on those boxes when we try to exclude the boot partition.
As you can see sometimes 0 is boot and sometimes 1
As you can see sometimes 0 is boot and sometimes 1
Edited by littlesat, 5 November 2019 - 17:54.
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
