Jump to content


Photo

Slow Boot after update to 7.2 VU+ Ultimo4K


  • Please log in to reply
10 replies to this topic

#1 ntj

  • Senior Member
  • 71 posts

0
Neutral

Posted 15 December 2019 - 14:57

Hi

 

Having long boot time since updating to 7.2

See logging below, (can send whole log file if needed)

Nearly 1 min at part marked in red. (something with tuning?)

(Can also write that LCDLinux is NOT installed as i have had problems before with that one)

Anyone with an idea about this?

 

 

Dec 15 14:27:48 vuultimo4k user.info kernel: [   26.339471] ata1: EH complete
Dec 15 14:27:48 vuultimo4k user.warn kernel: [   26.381096] ata1: limiting SATA link speed to 3.0 Gbps
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.386273] ata1.00: exception Emask 0x10 SAct 0x20000000 SErr 0x1380000 action 0x6 frozen
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.394561] ata1.00: irq_stat 0x08000000, interface fatal error
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.400500] ata1: SError: { 10B8B Dispar BadCRC TrStaTrns }
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.406096] ata1.00: failed command: READ FPDMA QUEUED
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.411256] ata1.00: cmd 60/a8:e8:e0:93:08/00:00:13:00:00/40 tag 29 ncq 86016 in
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.411256]          res 40/00:ec:e0:93:08/00:00:13:00:00/40 Emask 0x10 (ATA bus error)
Dec 15 14:27:48 vuultimo4k user.err kernel: [   26.426671] ata1.00: status: { DRDY }
Dec 15 14:27:48 vuultimo4k user.info kernel: [   26.430355] ata1: hard resetting link
Dec 15 14:27:49 vuultimo4k user.info kernel: [   26.702067] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
Dec 15 14:27:49 vuultimo4k user.info kernel: [   26.721173] ata1.00: configured for UDMA/133
Dec 15 14:27:49 vuultimo4k user.info kernel: [   26.725501] ata1: EH complete
Dec 15 14:27:55 vuultimo4k user.warn kernel: [   33.262069] >>cid=1, sid=0 r=0 s=0
Dec 15 14:27:55 vuultimo4k user.warn kernel: [   33.265501] ROLT
Dec 15 14:27:56 vuultimo4k user.warn kernel: [   33.703075] >>cid=1, sid=0 r=2 s=0
Dec 15 14:28:50 vuultimo4k user.warn kernel: [   87.895267] FE tune
Dec 15 14:28:50 vuultimo4k user.warn kernel: [   88.208075] >>cid=1, sid=0 r=2 s=0
Dec 15 14:28:50 vuultimo4k user.warn kernel: [   88.216711] [AUD]: AUDIO_SELECT_SOURCE 0
Dec 15 14:28:50 vuultimo4k user.warn kernel: [   88.221552] [AUD]: AUDIO_SET_BYPASS_MODE 1
Dec 15 14:28:50 vuultimo4k user.warn kernel: [   88.226174] [AUD]: downmix 1 state : 1

 

 

Regards



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #2 ntj

  • Senior Member
  • 71 posts

0
Neutral

Posted 21 December 2019 - 14:32

Bump

 

 Anyone have any guess where to start looking ?

 

Since writing i have tried reflash with the image from 16 Dec and no difference.

On screen when it is "pausing" during boot i will see the "Boot screen with the build date" and the channel info in the bottom of the screen but the clock to the lower left corner is not "ticking" and the Tuner info in the lower right corner shows the correct tuner letter but in Yellow (goes green after this long "paus")

When done booting everything seems normal.

 

Anyone any input?

 

Regards



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #3 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 21 December 2019 - 15:38

It is a known issue that the VU+ drivers take ridiculously long to load and initialize, it is not limited to the Ultimo. It has already been reported twice.

 

Also, you have disk errors in your log, that probably isn't helping.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Slow Boot after update to 7.2 VU+ Ultimo4K #4 ntj

  • Senior Member
  • 71 posts

0
Neutral

Posted 21 December 2019 - 16:04

Hi

 

Thank you for the answer

Was the drivers updated from 7.1 to 7.2 as it was much faster booting with 7.1?

 

Will check the disk.

 

Regards



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #5 greg197979

  • New Member
  • 2 posts

0
Neutral

Posted 21 December 2019 - 18:26

Hi. 

Is there any chance to find openpli 7.1 version as my duo 4k has crashed after update to 7.2.

 

Thanks



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #6 betacentauri

  • PLi® Core member
  • 7,185 posts

+323
Excellent

Posted 21 December 2019 - 18:40

Just flash 7.2 image with USB stick. Updating can make trouble.
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04

Re: Slow Boot after update to 7.2 VU+ Ultimo4K #7 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,380 posts

+393
Excellent

Posted 1 February 2020 - 15:13

@ntj,

 

My Ultimo4K boots in less then a minute and an online flash including booting takes somewhere between 3-4 minutes max.


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.


Re: Slow Boot after update to 7.2 VU+ Ultimo4K #8 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 1 February 2020 - 15:14

If there is a hanging mount, the default kernel driver timeout is 120 seconds.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Slow Boot after update to 7.2 VU+ Ultimo4K #9 ntj

  • Senior Member
  • 71 posts

0
Neutral

Posted 1 February 2020 - 15:54

Thank you for pointing me into a new direction, i was sure it was related to tuners and drivers (or a setup fault with tuners)

I now disconnected the LAN cable from my Ultimo4k and it is now booting very fast without delay during boot. connect it again and boot is slow.

Question is why as i only using a internal HDD and only use the LAN for "update and EPG"



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #10 ntj

  • Senior Member
  • 71 posts

0
Neutral

Posted 1 February 2020 - 16:07

Did find an old NAS mounting in the settings from way back in time (Now disabled and is booting in 40 sec.)



Re: Slow Boot after update to 7.2 VU+ Ultimo4K #11 WanWizard

  • PLi® Core member
  • 68,309 posts

+1,719
Excellent

Posted 1 February 2020 - 16:15

:thumbs-up:


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users