Jump to content


Photo

Et9000 bootet nicht seit Pli7.2


  • Please log in to reply
10 replies to this topic

#1 Obi70

  • Member
  • 5 posts

0
Neutral

Posted 4 February 2020 - 17:29

Hallo,

 

ich benutze schon über 6 Jahre das Pli Image, sonst kam ich immer damit zurecht.

Seit der 7.2 Version hat sich glaube ich mein Flashspeicher vollgeschrieben 128MB.

Ich hatte ein paar Plugins installiert und dann kam die Meldung: no Space left on device.

Dann machte ich noch ein Software update nun bootet der Receiver nicht mehr.

 

Ich mach ihn an und dann sehe ich nur noch den Startbildschirm mit Pli Image 7.2.

Dann versuchte ich ihn neu zu flashen mit usb Stick und den Image 4-7 -funktioniert nicht.

Ich starte den Receiver mit eingesteckten Usb und dann fragt er neues Image erkannt, dann drücke ich ok fürs flashen. Dann zeigt er flashing an und springt nach einigen Sekunden wieder zum Startbildschirm von pli Image 7.2 hin, und das wars.

Per FileZilla kann ich auf die  Box zugreifen.

Nun weis ich nicht mehr weiter.

Ich hatte folgendes in einen anderen Forum gelesen:

Aber für deine Box, die ja nur 128 MB Flash hat, rate ich dir folgendes. Installiere nur ein Grundimage auf deiner Box, ohne weitere Plugins. Danach installiere dir das Plugin OpenMultiboot. Stecke einen USB-Stick an deine Box und auf diesen kannst du nun weitere Images installieren, oder auch nur ein Image, mit dem du dann arbeiten kannst, mit fast beliebig vielen Plugins. USB-Stick musst du dann natürlich immer an der Box lassen.

Dafür müsste ich erst auf die Box wieder zugreifen.

Hat einer eine Idee ?

 

 



Re: Et9000 bootet nicht seit Pli7.2 #2 Obi70

  • Member
  • 5 posts

0
Neutral

Posted 4 February 2020 - 17:47

OpenPLi Enigma2 crash log
crashdate=Di Feb  4 11:57:52 2020
compiledate=Jan 27 2020
skin=PLi-FullNightHD/skin.xml
sourcedate=2020-01-21
branch=release-7.2
rev=c2d37ea
component=Enigma2
stbmodel=et9000
stbmodel=dm800se
kernelcmdline= bmem=216M ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs console=null consoleblank=0
nimsockets=NIM Socket 0:
imageissue=openpli 7.2-release %h

REMOVE Peer et9x00
REMOVE Peer et9x00
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eDVBPESReader] ERROR reading PES (fd=56): Value too large for defined data type
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eDVBPESReader] ERROR reading PES (fd=58): Value too large for defined data type
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eDVBPESReader] ERROR reading PES (fd=58): Value too large for defined data type
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
[eListboxPythonConfigContent] second value of tuple is not a tuple.
Unhandled Error
Traceback (most recent call last):
  File "/usr/lib/python2.7/site-packages/twisted/internet/defer.py", line 310, in addCallbacks
   
  File "/usr/lib/python2.7/site-packages/twisted/internet/defer.py", line 653, in _runCallbacks
   
  File "/usr/lib/python2.7/site-packages/twisted/internet/base.py", line 441, in _continueFiring
   
  File "/usr/lib/python2.7/site-packages/twisted/internet/base.py", line 671, in disconnectAll
   
--- <exception caught here> ---
  File "/usr/lib/python2.7/site-packages/twisted/python/log.py", line 103, in callWithLogger
   
  File "/usr/lib/python2.7/site-packages/twisted/python/log.py", line 86, in callWithContext
   
  File "/usr/lib/python2.7/site-packages/twisted/python/context.py", line 122, in callWithContext
   
  File "/usr/lib/python2.7/site-packages/twisted/python/context.py", line 85, in callWithContext
   
  File "/usr/lib/python2.7/site-packages/twisted/internet/unix.py", line 420, in connectionLost
   
exceptions.OSError: [Errno 2] No such file or directory: '/tmp/hotplug.socket'
 
dmesg
<6>Brought up 2 CPUs
<6>devtmpfs: initialized
<6>NET: Registered protocol family 16
<6>USB0: power enable is active low; overcurrent is active low
<6>PCI2.3->SDRAM window: 512 MB
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Initialized.
<6>PCI host bridge to bus 0000:00
<6>pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
<6>pci_bus 0000:00: root bus resource [io  0x0400-0x83ff]
<6>pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
<7>pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
<6>PCI host bridge to bus 0000:01
<6>pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
<6>pci_bus 0000:01: root bus resource [io  0x8400-0x87ff]
<6>pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
<7>pci 0000:01:00.0: [14e4:8602] type 00 class 0x01010f
<6>PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
<7>pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
<7>pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
<7>pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
<6>pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
<6>pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
<6>Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource upg
<5>FS-Cache: Loaded
<6>NET: Registered protocol family 2
<6>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP: reno registered
<6>UDP hash table entries: 256 (order: 1, 8192 bytes)
<6>UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>PCI: CLS 0 bytes, default 64
<5>NFS: Registering the id_resolver key type
<5>Key type id_resolver registered
<5>Key type id_legacy registered
<6>fuse init (API version 7.20)
<6>msgmni has been set to 567
<6>io scheduler noop registered
<6>io scheduler cfq registered (default)
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<6>serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
<6>serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
<6>serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
<6>loop: module loaded
<7>sata_brcmstb 0000:01:00.0: version 4.0
<7>__clk_enable: sata [1]
<4>PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
<7>sata_brcmstb 0000:01:00.0: setting latency timer to 64
<6>scsi0 : sata_brcmstb
<6>scsi1 : sata_brcmstb
<6>ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
<6>ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
<6>Broadcom STB NAND controller (BrcmNand Controller)
<6>bcmemac: Broadcom STB 10/100 EMAC driver v3.0
<6>bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:a6:e9)
<6>bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
<6>usbcore: registered new interface driver zd1201
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<7>__clk_enable: usb [1]
<6>ehci-brcm ehci-brcm.0: Broadcom STB EHCI
<6>ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
<6>ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
<6>ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ehci-brcm ehci-brcm.1: Broadcom STB EHCI
<6>ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
<6>ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
<6>ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>ohci-brcm ohci-brcm.0: Broadcom STB OHCI
<6>ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
<6>ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>ohci-brcm ohci-brcm.1: Broadcom STB OHCI
<6>ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
<6>ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>mousedev: PS/2 mouse device common for all mice
<6>i2c /dev entries driver
<6>usbcore: registered new interface driver btusb
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>TCP: cubic registered
<6>NET: Registered protocol family 17
<6>Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>Bluetooth: HIDP socket layer initialized
<5>Key type dns_resolver registered
<6>EBI CS1: setting up NAND flash (primary)
<6>mtd->oobsize=0, mtd->eccOobSize=0
<4>NAND_CS_NAND_XOR=00000000
<4>B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
<4>brcmnand_read_id: CS1: dev_id=ecf10095
<4>After: NandSelect=50000200, nandConfig=15142200
<4>Block size=00020000, erase shift=17
<6>NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
<6>busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
<4>timing1 not adjusted: 5363444f
<4>timing2 not adjusted: 00000fc6
<4>eccLevel=15, 1Ksector=0, oob=16
<4>nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<4><--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
<6>BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
<6>
<6>Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
<6>BrcmNAND version = 0x0302 128MB @00000000
<4>B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
<4>brcmnand_read_id: CS1: dev_id=ecf10095
<4>After: NandSelect=50000200, nandConfig=15142200
<4>Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
<4>brcmnand_scan: B4 nand_select = 50000200
<4>brcmnand_scan: After nand_select = 50000200
<6>page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
<6>Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
<4>ECC layout=brcmnand_oob_bch4_4k
<6>brcmnand_scan:  mtd->oobsize=64
<6>brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
<6>brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
<4>-->brcmnand_default_bbt
<4>brcmnand_default_bbt: bbt_td = bbt_main_descr
<7>Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS1
<7>Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS1
<4>Adjust partition complete size from entire device to 7f00000 to avoid overlap with BBT reserved space
<4>Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space
<5>Creating 3 MTD partitions on "brcmnand.0":
<5>0x000000000000-0x000007f00000 : "complete"
<5>0x000000000000-0x000000600000 : "kernel"
<5>0x000000600000-0x000007f00000 : "rootfs"
<6>PM: CP0 COUNT/COMPARE frequency depends on divisor
<5>UBI: attaching mtd2 to ubi0
<6>usb 2-1: new high-speed USB device number 2 using ehci-brcm
<6>hub 2-1:1.0: USB hub found
<6>hub 2-1:1.0: 4 ports detected
<6>usb 2-1.2: new full-speed USB device number 3 using ehci-brcm
<5>UBI: scanning is finished
<5>UBI: attached mtd2 (name "rootfs", size 121 MiB) to ubi0
<5>UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
<5>UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
<5>UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
<5>UBI: good PEBs: 968, bad PEBs: 0, corrupted PEBs: 0
<5>UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
<5>UBI: max/mean erase counter: 42/9, WL threshold: 4096, image sequence number: 157614232
<5>UBI: available PEBs: 0, total reserved PEBs: 968, PEBs reserved for bad PEB handling: 20
<5>UBI: background thread "ubi_bgt0d" started, PID 49
<6>ALSA device list:
<6>  No soundcards found.
<4>Warning: unable to open an initial console.
<6>ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
<6>ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
<6>ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
<6>ata1.00: configured for UDMA/133
<5>scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD204UI  1AQ1 PQ: 0 ANSI: 5
<5>sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1
<5>sd 0:0:0:0: [sda] Attached SCSI disk
<6>ata2: SATA link down (SStatus 4 SControl 300)
<5>UBIFS: background thread "ubifs_bgt0_0" started, PID 51
<5>UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)
<5>UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
<5>UBIFS: FS size: 118468608 bytes (112 MiB, 933 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
<5>UBIFS: reserved for root: 0 bytes (0 KiB)
<5>UBIFS: media format: w4/r0 (latest is w4/r0), UUID EDA44B85-4E24-470B-BE8B-7F55F4519C18, small LPT model
<6>VFS: Mounted root (ubifs filesystem) on device 0:10.
<6>devtmpfs: mounted
<6>Freeing unused kernel memory: 316k freed
<4>EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
<6>EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
<6>usbcore: registered new interface driver tpm
<4>dvb: module_layout: kernel tainted.
<4>Disabling lock debugging due to kernel taint
<6>Console: switching to colour frame buffer device 160x45
<6>input: dreambox remote control (native) as /devices/virtual/input/input0
<6>input: dreambox advanced remote control (native) as /devices/virtual/input/input1
<6>DVB: registering new adapter (dvb0)
<6>platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
<6>platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...
<6>input: front panel as /devices/virtual/input/input2
<6>Console: switching to colour dummy device 80x25
<6>NET: Registered protocol family 10
<6>Installing knfsd (copyright © 1996 okir@monad.swb.de).
<6>NFS: bad mount option value specified: vers=4.2
<6>NFS: bad mount option value specified: vers=4.2
<4>UBIFS warning (pid 919): ubifs_vm_page_mkwrite: out of space for mmapped file (inode number 8942)
<4>UBIFS warning (pid 919): ubifs_vm_page_mkwrite: out of space for mmapped file (inode number 8942)


Re: Et9000 bootet nicht seit Pli7.2 #3 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,380 posts

+393
Excellent

Posted 4 February 2020 - 21:00

Leider ist das Image meiner Meinung nach zu groß geworden. Picons mußt du unbedingt nicht herunterladen. Dann gibt es bald ‚no space left on device‘. Die Boxen kann man am besten nur noch mit 4.0 oder mit 6.2 laden. Sind auch schon 8+ Jahre alt also am Ende ihres Lebens. ;)


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.


Re: Et9000 bootet nicht seit Pli7.2 #4 Obi70

  • Member
  • 5 posts

0
Neutral

Posted 5 February 2020 - 00:26

Gibt es denn eine Möglichkeit den Receiver wieder in Betrieb zu nehmen.

no space left on device hatte ich schon, kann ich per ftp was löschen oder

per telnet ein befehl eingeben. ;)  :wub:  :blink:

Reset oder sowas ?

 

Eigentlich hat der Receiver(ct9100) bisher alles erledigt, sehr gutes Bild + schnelle Umschaltzeiten oder ist die Kiste nun im Eimer ? 

Kann ich irgendwie zurück flashen ?



Re: Et9000 bootet nicht seit Pli7.2 #5 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,380 posts

+393
Excellent

Posted 5 February 2020 - 07:23

Selbstverständlich kannst du die Box mit 4.0 flashen. Damit funktioniert die Box noch einigermaßen. Dann müßtest du frisch flashen via USB. 
Dann kannst du die Box noch benutzen. 


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.


Re: Et9000 bootet nicht seit Pli7.2 #6 rantanplan

  • PLi® Contributor
  • 1,760 posts

+81
Good

Posted 5 February 2020 - 11:52

Ist etwas Pech die Box mit kleinem Speicher erwischt zu haben.

Da wird die Installation tatsächlich zum Abenteuer.

Die meisten 9xxx laufen aber auch mit aktuellem Image sorgenfrei.

Hat man sich einmal die Box bzgl Speicher so "Überladen", dann bleibt nur neu flashen und einrichten.

Bei 7.2 dann direkt Flashexpander installieren und alle gewünschten Plugins dann auf USB installeren.

Alternativ PluginSkinmover, der auch für die Auslagerung der zusätzlichen Plugins auf USB sorgt.

 

Das klappt gut.....Aber!

Dann Finger weg von ständiger Aktualisierung.

Genauso ist es wenig Ratsam dann die Wiederherstellung nach Neuflash zu nutzen.

Dann würde wieder direkt der Speicher mit allen installierten Plugins überlaufen.

 

Grüße



Re: Et9000 bootet nicht seit Pli7.2 #7 Obi70

  • Member
  • 5 posts

0
Neutral

Posted 5 February 2020 - 12:53

hi,

Ich versuchte schon neu zu flashen, irgendwie klappt das nicht.

 

meine erste Nachricht: 

 

ich mach ihn an und dann sehe ich nur noch den Startbildschirm mit Pli Image 7.2.

Dann versuchte ich ihn neu zu flashen mit usb Stick und den Image 4-7 -funktioniert nicht.

Ich starte den Receiver mit eingesteckten Usb und dann fragt er neues Image erkannt, dann drücke ich ok fürs flashen. Dann zeigt er flashing an und springt nach einigen Sekunden wieder zum Startbildschirm von pli Image 7.2 hin, und das wars.

Per FileZilla kann ich auf die  Box zugreifen.

Nun weis ich nicht mehr weiter.

 

Ich habe schon 3 Sticks probiert.Ich habe es mit den Pli Image 4 probiert.



Re: Et9000 bootet nicht seit Pli7.2 #8 rantanplan

  • PLi® Contributor
  • 1,760 posts

+81
Good

Posted 5 February 2020 - 14:13

klingt nach falschem USB-Port, hast den vorderen USB-Prot genommen und auch sonst alles andere abgezogen?

 

Wenn noch auf die Box kommst, dann könntest du auch via angeschlossener USB/HDD hinten und Telnet das Image via ofgwrite in die Box "hauen".

 

Telnet(putty) vom PC starten und verbinden

ofgwrite /Pfad des Sticks/Pfad des entpackten ImagesOrdner  (also z.B. so ofgwrite /media/hdd/enigma2)

 

Grüße



Re: Et9000 bootet nicht seit Pli7.2 #9 Obi70

  • Member
  • 5 posts

0
Neutral

Posted 5 February 2020 - 17:45

Hallo, 

 

vielen Dank an alle, Box läuft wieder openPli 7.2 vom 3.2.2020) drauf   :) .

Habe einen Usb Stick von Rossman gekauft(store.it).

Damit konnte ich wieder mit flashen.

Ich versuche bevor ich alles wieder installiere, zuerst Flashexpander zu installieren und

lasse den Stick drinne.

Kann ich statt den Stick auch die Festplatte benutzen.



Re: Et9000 bootet nicht seit Pli7.2 #10 Frenske

  • Forum Moderator
    PLi® Core member
  • 27,380 posts

+393
Excellent

Posted 5 February 2020 - 19:33

Das letzte würde ich niemals tun. Sonst bleibt die Festplatte (fast) immer aktiv und wenn die Picons auf der Festplatte stecken, dann startet die Festplatte sobald man wechselt von Sender. 


Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.

Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. ;) :)
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.

Voor centrale opslag van media gebruik ik een Qnap 219P 
met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.

-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".

Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.


Re: Et9000 bootet nicht seit Pli7.2 #11 mikel

  • Senior Member
  • 441 posts

0
Neutral

Posted 23 April 2020 - 08:55

Hallo Obi70,

 

funktioniert auf deiner Box noch das Secbord? Wenn ja, warum bleibst du nicht bei dem 4.0 Image?

Das Image ist für eine Xtrend ET9000 das beste Image und es funzt auch eigentlich alles was man will, trotz 128 MB Flashspeicher. Installiere das letzte Pli 4.0, dann nach und nach die gewünschten Plugins installieren, zwischendurch bei nicht ganz ausgereiztem Flahspeicher Backup machen und wieder damit Flashen, bringt ca. bis zu 10 MB. Auf meiner ET9000 läuft Mediapotal, HBBTV und selbst Picons intern abgelegt, ect. und die fressen einiges an Speicher, mit den Images größer als 4.0 nicht zu machen. Mit Multiboot ect. über einen Stick, kein Vergleich zu intern.

 

Einfach mal ein wenig Zeit nehmen, das Image ist dann bis auf ein paar neue Updates die noch von einigen Plugins kommen (Mediaportal) fertig und es bedarf keiner Änderung mehr. Für das Update Mediaportal sollte ein gewisser Speicher zur Verfügung stehen um die 100 MB wenn möglich etwas weniger, sonst gibt es eine Fehlermeldung.

 

Viel Spaß.

 

Gruß Mikel


Edited by mikel, 23 April 2020 - 08:56.



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users