Springen naar inhoud


Foto

PLi 6.1 snmp support dm8000

Snmp monitoring

  • Please log in to reply
Er zijn 5 reacties in dit onderwerp

#1 B69

  • New Member
  • 3 berichten

0
Neutral

Geplaatst op 16 februari 2020 - 19:28

Anyone running snmp on pli 6.1?
I'm trying to achieve the following:

When it's snowing heavily, it sometines builds up on antenna, redusing signal strength below critical level, leading to corrupt recordings.

I'd like to monitor signal strength and trigger an alert if dB value decreases below a set value.
Another value to monitor are free disk space for recordings.

It struck my mind that the best way ro do this was to use an snmp tool to reading off these values every 5 minutes from my good old dreambox 8000.

The sw repository don't have any snmp plugins, at least not on my pli 6.1 installation, however I read somewhere that there should exist a snmp plugin for openpli. So I turn to the experts for advice:)
Many thanks for any advice.

Re: PLi 6.1 snmp support dm8000 #2 WanWizard

  • PLi® Core member
  • 68307 berichten

+1719
Excellent

Geplaatst op 16 februari 2020 - 21:59

There is an snmpagent plugin in the feeds, which looks like it does what you want (I see BER/AGC/SNR/SNRdB/LOCK values in the OID list). But I've never used it.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: PLi 6.1 snmp support dm8000 #3 mrbeam

  • Senior Member
  • 300 berichten

+6
Neutral

Geplaatst op 17 februari 2020 - 00:00

I did use it a long time ago, and then it worked flawless. 


Wavefrontier T90, Vu+ Duo 4k SE (DVB-S2x FBC, DVB-T2, DVB-C USB), Octagon SF4008 (dual DVB-S2, DVB-T2 & DVB-C USB), Mutant HD51 (DVB-S2 & DVB-T2), TBS6920 & TBS6925


Re: PLi 6.1 snmp support dm8000 #4 B69

  • New Member
  • 3 berichten

0
Neutral

Geplaatst op 17 februari 2020 - 01:07

Many thanks for replys. Why don't I see the snmp plugin in the feeds? I'm using openpli 6.1 and original dm8000 hw. Please describe what procedure you perform to get it from the feed since I'm a bit clueless why I don't find it. Many thanks

Re: PLi 6.1 snmp support dm8000 #5 WanWizard

  • PLi® Core member
  • 68307 berichten

+1719
Excellent

Geplaatst op 17 februari 2020 - 10:19

It is available in the 6-release feed:

./mips32el/enigma2-plugin-extensions-snmpagent_2.0+git11+461b207-r0.3_mips32el.ipk

maybe already installed?
 


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: PLi 6.1 snmp support dm8000 #6 B69

  • New Member
  • 3 berichten

0
Neutral

Geplaatst op 18 februari 2020 - 01:53

Finally found it and installed it, many thanks!


1 gebruiker(s) lezen dit onderwerp

0 leden, 1 bezoekers, 0 anonieme gebruikers