Er zijn 27 reacties in dit onderwerp

[Wizard1]

Hi All

 

I'm hoping someone can point me in the right direction.  I own an Xtrend ET8500 with 2x S2 Tuners.  I want to add an extra Tuner for (UK Freeview) Terrestrial.  I've obtained a DVB Sky USB Tuner & have been told that it is compatible with my Xtrend & is compatible with the Openpli (7.2) Image.  I've been through every Driver in the Plugin Downloads, but unfortunately cannot get the Xtrend to recognise it. 

 

The only Identifying marks on the USB Tuner are DVB Sky & on the reverse side DVD-T/T2/C.  It is White in colour. 

 

Regards

 

Wizard

[WanWizard]

If you have the skills to login with telnet, do so, issue the command "lsusb" with the device plugged in, so we can see the device ID and figure out if a driver for it is available.

[Wizard1]

Hi WanWizard

 

I see the following result:

 

Bus 001 Device 002: ID 0572:0320

Bus 001 Device 001: ID 1d6b:0002

Bus 001 Device 001: ID 1d6b:0002

Bus 001 Device 001: ID 1d6b:0002

Bus 001 Device 001: ID 1d6b:0002

Bus 001 Device 001: ID 1d6b:0001

Bus 001 Device 001: ID 1d6b:0001

Bus 001 Device 001: ID 1d6b:0001

Bus 001 Device 001: ID 1d6b:0001

 

Hope this helps.

 

Wizard

[WanWizard]

Device 0572:0320 requires the "kernel-module-dvb-usb-dvbsky" package, which can be installed via software management, package management, or via the commandline using:

opkg install kernel-module-dvb-usb-dvbsky

 

[Wizard1]

Hi WanWizard

 

I've followed your instructions (opkg install kernel-module-dvb-usb-dvbsky) & rebooted the Xtrend.  The Tuner is still not recognised & I don't see any additional drivers to install.  Am I missing something ?

 

Regards

 

Wizard

[WTE]

Hi WanWizard

 

I've followed your instructions (opkg install kernel-module-dvb-usb-dvbsky) & rebooted the Xtrend.  The Tuner is still not recognised & I don't see any additional drivers to install.  Am I missing something ?

 

Regards

 

Wizard

Wait will box is boot and then connect the USB device.

After that is done can you post the last messages from telnet/putty command: dmesg

[Wizard1]

Hi WTE

 

I've followed your advice, unfortunately still not recognising the USB Tuner.  I've borrowed & fitted a Xtrend DVC/T/T2 Internal Tuner, that works fine.  Below is the Information you requested. 

 

root@et8500:~# dmesg
serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM10406780 IRQ54): -28
loop: module loaded
ahci strict-ahci.0: SSS flag set, parallel bus scan disabled
ahci strict-ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl platform mode
ahci strict-ahci.0: flags: ncq sntf stag clo pmp slum part
scsi host0: ahci
scsi host1: ahci
scsi host2: ahci
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 33
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 33
ata3: DUMMY
brcmstb_nand: NAND controller driver is loaded
libphy: Fixed: probed
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0: GENET 3.1 EPHY: 0x00b0
libphy: bcmgenet MII bus: probed
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
bcm7429_pm_network_disable 00
usbcore: registered new interface driver r8152
hso: /openpli/oe/release-7.2/build/tmp/work-shared/et8500/kernel-source/drivers/net/usb/hso.c: Option Wireless
usbcore: registered new interface driver hso
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver ipheth
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver lg-vl600
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 56, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 61, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 62, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 58, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 59, io mem 0x10480600
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 63, io mem 0x10490400
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: HITACHI HTS727550A9E364, JF3ZD0H0, max UDMA/100
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      HITACHI HTS72755 D0H0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 64, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver appletouch
usbcore: registered new interface driver bcm5974
usbcore: registered new interface driver synaptics_usb
i2c /dev entries driver
usbcore: registered new interface driver btusb
hidraw: raw HID events driver © Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS1: setting up NAND flash (primary)
nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
nand: Samsung NAND 512MiB 3,3V 8-bit
nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4

Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000020000000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000020000000 : "rootfs"
EBI CS0: setting up SPI flash
spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
m25p80 spi0.0: found s25sl032p, expected m25p80
m25p80 spi0.0: s25sl032p (4096 Kbytes)
ubi0: attaching mtd2
 sda: sda1
ata2: SATA link down (SStatus 0 SControl 300)
sd 0:0:0:0: [sda] Attached SCSI disk
random: nonblocking pool is initialized
ubi0: scanning is finished
ubi0: attached mtd2 (name "rootfs", size 506 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 4044, bad PEBs: 4, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 8194/4075, WL threshold: 4096, image sequence number: 137566636
ubi0: available PEBs: 0, total reserved PEBs: 4044, PEBs reserved for bad PEB handling: 76
ubi0: background thread "ubi_bgt0d" started, PID 86
ALSA device list:
  No soundcards found.
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 87
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 501936128 bytes (478 MiB, 3953 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 80C3A80F-762A-419A-86E1-9EE0BC7AC5B3, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:14.
devtmpfs: mounted
Freeing unused kernel memory: 224K (80928000 - 80960000)
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
DVB: registering new adapter (et8500)
platform et8500.0: DVB: registering adapter 0 frontend 0 (AVL6211)...
platform et8500.0: DVB: registering adapter 0 frontend 1 (AVL6211)...
platform et8500.0: DVB: registering adapter 0 frontend 2 (Si216x)...
input: dreambox remote control (native) as /devices/virtual/input/input0
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0: configuring instance for external RGMII (TX delay)
NET: Registered protocol family 10
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
bcmgenet bcmgenet.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
usb 1-1: new high-speed USB device number 2 using ehci-brcm
usb 1-1: dvb_usb_v2: found a 'DVBSky T330' in warm state
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (DVBSky T330)
usb 1-1: dvb_usb_v2: MAC address: 00:cc:10:a5:33:0c
i2c i2c-0: Added multiplexed i2c bus 1
si2168 0-0064: Silicon Labs Si2168 successfully attached
si2157 1-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
usb 1-1: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
IR keymap rc-dvbsky not found
Registered IR keymap rc-empty
input: DVBSky T330 as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input1
rc0: DVBSky T330 as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0
usb 1-1: dvb_usb_v2: schedule remote query interval to 300 msecs
usb 1-1: dvb_usb_v2: 'DVBSky T330' successfully initialized and connected
usbcore: registered new interface driver dvb_usb_dvbsky
si2168 0-0064: found a 'Silicon Labs Si2168-B40'
si2168 0-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 0-0064: firmware version: 4.0.11
si2157 1-0060: found a 'Silicon Labs Si2158-A20'
si2157 1-0060: Direct firmware load for dvb-tuner-si2158-a20-01.fw failed with error -2
si2157 1-0060: firmware file 'dvb-tuner-si2158-a20-01.fw' not found
usb 1-1: USB disconnect, device number 2
root@et8500:~#

 

Hope this helps.

 

Wizard

Veranderd door Wizard1, 22 mei 2020 - 20:43

[WanWizard]

si2157 1-0060: Direct firmware load for dvb-tuner-si2158-a20-01.fw failed with error -2
si2157 1-0060: firmware file 'dvb-tuner-si2158-a20-01.fw' not found

 

This means you're missing the device firmware:

opkg install firmware-dvb-tuner-si2158-a20

 

[Wizard1]

Hi Guys

 

Still No Luck.  I've sent the command opkg install firmware-dvb-tuner-si2158-a20  I still don't see the Tuner.  Below is the dmesg.

 

root@et8500:~# root@et8500:~# dmesg
-sh: root@et8500:~#: not found
root@et8500:~# FS-Cache: Loaded
-sh: FS-Cache:: not found
root@et8500:~# NET: Registered protocol family 2
-sh: NET:: not found
root@et8500:~# TCP established hash table entries: 8192 (order: 3, 32768 bytes)
-sh: syntax error: unexpected "("
root@et8500:~# TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
-sh: syntax error: unexpected "("
root@et8500:~# TCP: Hash tables configured (established 8192 bind 8192)
-sh: syntax error: unexpected "("
root@et8500:~# UDP hash table entries: 512 (order: 2, 16384 bytes)
-sh: syntax error: unexpected "("
root@et8500:~# UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
-sh: syntax error: unexpected "("
root@et8500:~# NET: Registered protocol family 1
-sh: NET:: not found
root@et8500:~# RPC: Registered named UNIX socket transport module.
-sh: RPC:: not found
root@et8500:~# RPC: Registered udp transport module.
-sh: RPC:: not found
root@et8500:~# RPC: Registered tcp transport module.
-sh: RPC:: not found
root@et8500:~# RPC: Registered tcp NFSv4.1 backchannel transport module.
-sh: RPC:: not found
root@et8500:~# futex hash table entries: 512 (order: 4, 65536 bytes)
-sh: syntax error: unexpected "("
root@et8500:~# NFS: Registering the id_resolver key type
-sh: NFS:: not found
root@et8500:~# Key type id_resolver registered
-sh: Key: not found
root@et8500:~# Key type id_legacy registered
-sh: Key: not found
root@et8500:~# nfs4filelayout_init: NFSv4 File Layout Driver Registering...
-sh: nfs4filelayout_init:: not found
root@et8500:~# Installing knfsd (copyright © 1996 okir@monad.swb.de).
-sh: syntax error: unexpected "("
root@et8500:~# fuse init (API version 7.23)
-sh: syntax error: unexpected "("
root@et8500:~# io scheduler noop registered
-sh: io: not found
root@et8500:~# io scheduler cfq registered (default)
-sh: syntax error: unexpected "("
root@et8500:~# Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
-sh: Serial:: not found
root@et8500:~# console [ttyS0] disabled
-sh: console: not found
root@et8500:~# serial8250.0: ttyS0 at MMIO 0x10406700 (irq = 52, base_baud = 506
2500) is a 16550A
-sh: syntax error: unexpected "("
root@et8500:~# console [ttyS0] enabled
-sh: console: not found
root@et8500:~# bootconsole [early0] disabled
-sh: bootconsole: not found
root@et8500:~# serial8250 serial8250.0: unable to register port at index 1 (IO0
MEM10406740 IRQ53): -28
-sh: syntax error: unexpected "("
root@et8500:~# serial8250 serial8250.0: unable to register port at index 2 (IO0
MEM10406780 IRQ54): -28
-sh: syntax error: unexpected "("
root@et8500:~# loop: module loaded
-sh: loop:: not found
root@et8500:~# ahci strict-ahci.0: SSS flag set, parallel bus scan disabled
-sh: ahci: not found
root@et8500:~# ahci strict-ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 im
pl platform mode
-sh: ahci: not found
root@et8500:~# ahci strict-ahci.0: flags: ncq sntf stag clo pmp slum part
-sh: ahci: not found
root@et8500:~# scsi host0: ahci
-sh: scsi: not found
root@et8500:~# scsi host1: ahci
-sh: scsi: not found
root@et8500:~# scsi host2: ahci
-sh: scsi: not found
root@et8500:~# ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x1
00 irq 33
-sh: ata1:: not found
root@et8500:~# ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x1
80 irq 33
-sh: ata2:: not found
root@et8500:~# ata3: DUMMY
-sh: ata3:: not found
root@et8500:~# brcmstb_nand: NAND controller driver is loaded
-sh: brcmstb_nand:: not found
root@et8500:~# libphy: Fixed: probed
-sh: libphy:: not found
root@et8500:~# __clk_enable: network [1]
-sh: __clk_enable:: not found
root@et8500:~# bcm7429_pm_network_enable 00
-sh: bcm7429_pm_network_enable: not found
root@et8500:~# __clk_enable: enet [1]
-sh: __clk_enable:: not found
root@et8500:~# bcm40nm_pm_genet_enable 00
-sh: bcm40nm_pm_genet_enable: not found
root@et8500:~# bcmgenet bcmgenet.0: GENET 3.1 EPHY: 0x00b0
-sh: bcmgenet: not found
root@et8500:~# libphy: bcmgenet MII bus: probed
-sh: libphy:: not found
root@et8500:~# __clk_disable: enet [0]
-sh: __clk_disable:: not found
root@et8500:~# bcm40nm_pm_genet_disable 00
-sh: bcm40nm_pm_genet_disable: not found
root@et8500:~# __clk_disable: network [0]
-sh: __clk_disable:: not found
root@et8500:~# bcm7429_pm_network_disable 00
-sh: bcm7429_pm_network_disable: not found
root@et8500:~# usbcore: registered new interface driver r8152
-sh: usbcore:: not found
root@et8500:~# hso: /openpli/oe/release-7.2/build/tmp/work-shared/et8500/kernel-
source/drivers/net/usb/hso.c: Option Wireless
-sh: hso:: not found
root@et8500:~# usbcore: registered new interface driver hso
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver asix
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver cdc_ether
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver net1080
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver cdc_subset
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver zaurus
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver ipheth
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver cdc_ncm
-sh: usbcore:: not found
root@et8500:~# usbcore: registered new interface driver lg-vl600
-sh: usbcore:: not found
root@et8500:~# ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
-sh: syntax error: unexpected "("
root@et8500:~# __clk_enable: usb [1]
-sh: __clk_enable:: not found
root@et8500:~# bcm40nm_pm_usb_enable 00
-sh: bcm40nm_pm_usb_enable: not found
root@et8500:~# ehci-brcm ehci-brcm.0: Broadcom STB EHCI
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbe
r 1
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.0: irq 56, io mem 0x10480300
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
-sh: ehci-brcm: not found
root@et8500:~# hub 1-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 1-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ehci-brcm ehci-brcm.1: Broadcom STB EHCI
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus numbe
r 2
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
-sh: ehci-brcm: not found
root@et8500:~# hub 2-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 2-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ehci-brcm ehci-brcm.2: Broadcom STB EHCI
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus numbe
r 3
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.2: irq 61, io mem 0x10490300
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
-sh: ehci-brcm: not found
root@et8500:~# hub 3-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 3-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ehci-brcm ehci-brcm.3: Broadcom STB EHCI
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus numbe
r 4
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.3: irq 62, io mem 0x10490500
-sh: ehci-brcm: not found
root@et8500:~# ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
-sh: ehci-brcm: not found
root@et8500:~# hub 4-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 4-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
-sh: syntax error: unexpected "("
root@et8500:~# ohci-brcm ohci-brcm.0: Broadcom STB OHCI
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbe
r 5
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.0: irq 58, io mem 0x10480400
-sh: ohci-brcm: not found
root@et8500:~# hub 5-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 5-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ohci-brcm ohci-brcm.1: Broadcom STB OHCI
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus numbe
r 6
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.1: irq 59, io mem 0x10480600
-sh: ohci-brcm: not found
root@et8500:~# hub 6-0:1.0: USB hub found
-sh: hub: not found
root@et8500:~# hub 6-0:1.0: 1 port detected
-sh: hub: not found
root@et8500:~# ohci-brcm ohci-brcm.2: Broadcom STB OHCI
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus numbe
r 7
-sh: ohci-brcm: not found
root@et8500:~# ohci-brcm ohci-brcm.2: irq 63, io mem 0x10490400
-sh: ohci-brcm: not found
root@et8500:~# ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
-sh: syntax error: unexpected "("
root@et8500:~# usb 1-1: new high-speed USB device number 2 using ehci-brcm
-sh: usb: not found
root@et8500:~# ata1.00: ATA-8: HITACHI HTS727550A9E364, JF3ZD0H0, max UDMA/100
-sh: ata1.00:: not found
root@et8500:~# ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
-sh: syntax error: unexpected "("
root@et8500:~# ata1.00: configured for UDMA/100
-sh: ata1.00:: not found
root@et8500:~# scsi 0:0:0:0: Direct-Access     ATA      HITACHI HTS72755 D0H0 PQ
: 0 ANSI: 5
-sh: scsi: not found
root@et8500:~# sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466
GiB)
-sh: syntax error: unexpected "("
root@et8500:~# sd 0:0:0:0: [sda] 4096-byte physical blocks
-sh: sd: not found
root@et8500:~# sd 0:0:0:0: Attached scsi generic sg0 type 0
-sh: sd: not found
root@et8500:~# sd 0:0:0:0: [sda] Write Protect is off
-sh: sd: not found
root@et8500:~# sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
-sh: sd: not found
root@et8500:~# sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does
n't support DPO or FUA
> hub 7-0:1.0: USB hub found
> hub 7-0:1.0: 1 port detected
> ohci-brcm ohci-brcm.3: Broadcom STB OHCI
> ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
> ohci-brcm ohci-brcm.3: irq 64, io mem 0x10490600
> hub 8-0:1.0: USB hub found
> hub 8-0:1.0: 1 port detected
> usbcore: registered new interface driver cdc_acm
> cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
> usbcore: registered new interface driver usb-storage
> mousedev: PS/2 mouse device common for all mice
> usbcore: registered new interface driver appletouch
> usbcore: registered new interface driver bcm5974
> usbcore: registered new interface driver synaptics_usb
> i2c /dev entries driver
> usbcore: registered new interface driver btusb
> hidraw: raw HID events driver © Jiri Kosina
> usbcore: registered new interface driver usbhid
> usbhid: USB HID core driver
> Initializing XFRM netlink socket
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> Key type dns_resolver registered
> PM: CP0 COUNT/COMPARE frequency does not depend on divisor
> EBI CS1: setting up NAND flash (primary)
> nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
> nand: Samsung NAND 512MiB 3,3V 8-bit
> nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit,
BCH-4
>
> Bad block table found at page 262080, version 0x01
> Bad block table found at page 262016, version 0x01
> Creating 3 MTD partitions on "brcmnand.0":
> 0x000000000000-0x000020000000 : "complete"
> 0x000000000000-0x000000600000 : "kernel"
> 0x000000600000-0x000020000000 : "rootfs"
> EBI CS0: setting up SPI flash
> spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
> spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
> m25p80 spi0.0: found s25sl032p, expected m25p80
> m25p80 spi0.0: s25sl032p (4096 Kbytes)
> ubi0: attaching mtd2
>  sda: sda1
> sd 0:0:0:0: [sda] Attached SCSI disk
> ata2: SATA link down (SStatus 0 SControl 300)
> random: nonblocking pool is initialized
> ubi0: scanning is finished
> ubi0: attached mtd2 (name "rootfs", size 506 MiB)
> ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
> ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
> ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
> ubi0: good PEBs: 4044, bad PEBs: 4, corrupted PEBs: 0
> ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
> ubi0: max/mean erase counter: 8194/4075, WL threshold: 4096, image sequence nu
mber: 137566636
> ubi0: available PEBs: 0, total reserved PEBs: 4044, PEBs reserved for bad PEB
handling: 76
> ALSA device list:
>   No soundcards found.
> ubi0: background thread "ubi_bgt0d" started, PID 87
> UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 88
> UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
> UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 20
48 bytes/2048 bytes
> UBIFS (ubi0:0): FS size: 501936128 bytes (478 MiB, 3953 LEBs), journal size 90
23488 bytes (8 MiB, 72 LEBs)
> UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
> UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 80C3A80F-762A-419A
-86E1-9EE0BC7AC5B3, small LPT model
> VFS: Mounted root (ubifs filesystem) on device 0:14.
> devtmpfs: mounted
> Freeing unused kernel memory: 224K (80928000 - 80960000)
> EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
> DVB: registering new adapter (et8500)
> platform et8500.0: DVB: registering adapter 0 frontend 0 (AVL6211)...
> platform et8500.0: DVB: registering adapter 0 frontend 1 (AVL6211)...
> platform et8500.0: DVB: registering adapter 0 frontend 2 (Si216x)...
> input: dreambox remote control (native) as /devices/virtual/input/input0
> usb 1-1: dvb_usb_v2: found a 'DVBSky T330' in warm state
> usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the soft
ware demuxer
> DVB: registering new adapter (DVBSky T330)
> usb 1-1: dvb_usb_v2: MAC address: 00:cc:10:a5:33:0c
> usbcore: registered new interface driver dvb_usb_dvbsky
> __clk_enable: network [1]
> bcm7429_pm_network_enable 00
> __clk_enable: enet [1]
> bcm40nm_pm_genet_enable 00
> bcmgenet bcmgenet.0: configuring instance for external RGMII (TX delay)
> NET: Registered protocol family 10
> IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> bcmgenet bcmgenet.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
> IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> root@et8500:~#

 

Regards
 

[WTE]

I think your ET8500 has a driver problem. The USB tuner seems to been initialized right.

[Wizard1]

Hi WTE

 

Thank you.  I'm not sure where I go from here

 

I'll start from scratch over the weekend, i'll install a fresh image & start again. 

 

Regards

 

Wizard

[Wizard1]

Hi Guys

 

I've installed a Fresh (OpenPli 7.2) Image onto my Xtrend ET8500 & used the following commands:

 

opkg install kernel-module-dvb-usb-dvbsky

 

opkg install firmware-dvb-tuner-si2158-a20

 

Unfortunately the Xtrend still doesn't see the USB Tuner.  I've posted the dmesg below.

 

root@et8500:~# dmesg
loop: module loaded
ahci strict-ahci.0: SSS flag set, parallel bus scan disabled
ahci strict-ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl platform mode
ahci strict-ahci.0: flags: ncq sntf stag clo pmp slum part
scsi host0: ahci
scsi host1: ahci
scsi host2: ahci
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 33
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 33
ata3: DUMMY
brcmstb_nand: NAND controller driver is loaded
libphy: Fixed: probed
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0: GENET 3.1 EPHY: 0x00b0
libphy: bcmgenet MII bus: probed
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
bcm7429_pm_network_disable 00
usbcore: registered new interface driver r8152
hso: /openpli/oe/release-7.2/build/tmp/work-shared/et8500/kernel-source/drivers/net/usb/hso.c: Option Wireless
usbcore: registered new interface driver hso
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver ipheth
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver lg-vl600
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 56, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 61, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 62, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 58, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 59, io mem 0x10480600
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 63, io mem 0x10490400
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 1-1: new high-speed USB device number 2 using ehci-brcm
ata1.00: ATA-8: HITACHI HTS727550A9E364, JF3ZD0H0, max UDMA/100
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      HITACHI HTS72755 D0H0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 64, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver appletouch
usbcore: registered new interface driver bcm5974
usbcore: registered new interface driver synaptics_usb
i2c /dev entries driver
usbcore: registered new interface driver btusb
hidraw: raw HID events driver © Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS1: setting up NAND flash (primary)
nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
nand: Samsung NAND 512MiB 3,3V 8-bit
nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4

Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000020000000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000020000000 : "rootfs"
EBI CS0: setting up SPI flash
spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
m25p80 spi0.0: found s25sl032p, expected m25p80
m25p80 spi0.0: s25sl032p (4096 Kbytes)
ubi0: attaching mtd2
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link down (SStatus 0 SControl 300)
random: nonblocking pool is initialized
ubi0: scanning is finished
ubi0: attached mtd2 (name "rootfs", size 506 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 4044, bad PEBs: 4, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 305419896
ubi0: available PEBs: 0, total reserved PEBs: 4044, PEBs reserved for bad PEB handling: 76
ALSA device list:
  No soundcards found.
ubi0: background thread "ubi_bgt0d" started, PID 87
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 88
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 501936128 bytes (478 MiB, 3953 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FA11418F-7528-44FF-AF71-9FC71C2604A9, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:14.
devtmpfs: mounted
Freeing unused kernel memory: 224K (80928000 - 80960000)
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
DVB: registering new adapter (et8500)
platform et8500.0: DVB: registering adapter 0 frontend 0 (AVL6211)...
platform et8500.0: DVB: registering adapter 0 frontend 1 (AVL6211)...
platform et8500.0: DVB: registering adapter 0 frontend 2 (Si216x)...
input: dreambox remote control (native) as /devices/virtual/input/input0
usb 1-1: dvb_usb_v2: found a 'DVBSky T330' in warm state
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (DVBSky T330)
usb 1-1: dvb_usb_v2: MAC address: 00:cc:10:a5:33:0c
i2c i2c-0: Added multiplexed i2c bus 1
si2168 0-0064: Silicon Labs Si2168 successfully attached
si2157 1-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
usb 1-1: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
IR keymap rc-dvbsky not found
Registered IR keymap rc-empty
input: DVBSky T330 as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input1
rc0: DVBSky T330 as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0
usb 1-1: dvb_usb_v2: schedule remote query interval to 300 msecs
usb 1-1: dvb_usb_v2: 'DVBSky T330' successfully initialized and connected
usbcore: registered new interface driver dvb_usb_dvbsky
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0: configuring instance for external RGMII (TX delay)
NET: Registered protocol family 10
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
bcmgenet bcmgenet.0 eth0: Link is Down
bcmgenet bcmgenet.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
si2168 0-0064: found a 'Silicon Labs Si2168-B40'
si2168 0-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 0-0064: firmware version: 4.0.11
si2157 1-0060: found a 'Silicon Labs Si2158-A20'
si2157 1-0060: downloading firmware from file 'dvb-tuner-si2158-a20-01.fw'
si2157 1-0060: firmware version: 2.1.9
root@et8500:~#

[WanWizard]

The device loads fine, so that's not it.

 

What is the output of

grep -r "" /proc/stb/bus 

?
 

[Wizard1]

Hi 

 

Below is the response

 

root@et8500:~# grep -r "" /proc/stb/bus
grep: /proc/stb/bus: No such file or directory
root@et8500:~#
 

[WanWizard]

Ok, alternative:

grep -r "" /proc/bus

 

[Wizard1]

Hi 

 

Below is the response

 

root@et8500:~# grep -r "" /proc/stb/bus
grep: /proc/stb/bus: No such file or directory
root@et8500:~# grep -r "" /proc/stb/bus
grep: /proc/stb/bus: No such file or directory
root@et8500:~#
root@et8500:~# grep -r "" /proc/stb/bus
grep: /proc/stb/bus: No such file or directory
root@et8500:~# grep -r "" /proc/bus
/proc/bus/input/devices:I: Bus=0019 Vendor=14e4 Product=0000 Version=000c
/proc/bus/input/devices:N: Name="dreambox remote control (native)"
/proc/bus/input/devices:P: Phys=brcmstb/input0
/proc/bus/input/devices:S: Sysfs=/devices/virtual/input/input0
/proc/bus/input/devices:U: Uniq=
/proc/bus/input/devices:H: Handlers=kbd event0
/proc/bus/input/devices:B: PROP=0
/proc/bus/input/devices:B: EV=100013
/proc/bus/input/devices:B: KEY=400000 118fcf52 22a476e1 0 0 0 c 2818000 51b8 58514d01 9eb7c0 0 38000000 ffc
/proc/bus/input/devices:B: MSC=10
/proc/bus/input/devices:
/proc/bus/input/devices:I: Bus=0003 Vendor=0572 Product=0320 Version=0000
/proc/bus/input/devices:N: Name="DVBSky T330"
/proc/bus/input/devices:P: Phys=usb-ehci_hcd-1/ir0
/proc/bus/input/devices:S: Sysfs=/devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input1
/proc/bus/input/devices:U: Uniq=
/proc/bus/input/devices:H: Handlers=kbd event1
/proc/bus/input/devices:B: PROP=0
/proc/bus/input/devices:B: EV=100013
/proc/bus/input/devices:B: KEY=1000000 0 0 0 0
/proc/bus/input/devices:B: MSC=10
/proc/bus/input/devices:
/proc/bus/input/handlers:N: Number=0 Name=rfkill
/proc/bus/input/handlers:N: Number=1 Name=kbd
/proc/bus/input/handlers:N: Number=2 Name=leds
/proc/bus/input/handlers:N: Number=3 Name=mousedev Minor=32
/proc/bus/input/handlers:N: Number=4 Name=evdev Minor=64
/proc/bus/nim_sockets:NIM Socket 0:
/proc/bus/nim_sockets:  Type: DVB-S2
/proc/bus/nim_sockets:  Name: AVL6211
/proc/bus/nim_sockets:  Frontend_Device: 0
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 0
/proc/bus/nim_sockets:NIM Socket 1:
/proc/bus/nim_sockets:  Type: DVB-S2
/proc/bus/nim_sockets:  Name: AVL6211
/proc/bus/nim_sockets:  Frontend_Device: 1
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 1
/proc/bus/nim_sockets:NIM Socket 2:
/proc/bus/nim_sockets:  Type: DVB-C
/proc/bus/nim_sockets:  Mode 0: DVB-T2
/proc/bus/nim_sockets:  Mode 1: DVB-C
/proc/bus/nim_sockets:  Mode 2: DVB-T
/proc/bus/nim_sockets:  Name: Si216x
/proc/bus/nim_sockets:  Frontend_Device: 2
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 2
root@et8500:~#
 

[WanWizard]

Good. So it sees the tuner just fine:

/proc/bus/nim_sockets:NIM Socket 2:
/proc/bus/nim_sockets:  Type: DVB-C
/proc/bus/nim_sockets:  Mode 0: DVB-T2
/proc/bus/nim_sockets:  Mode 1: DVB-C
/proc/bus/nim_sockets:  Mode 2: DVB-T
/proc/bus/nim_sockets:  Name: Si216x
/proc/bus/nim_sockets:  Frontend_Device: 2
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 2

So you should have an A, B and C tuner now.
 

[Wizard1]

Hi WanWizard

 

No, Tuner C is an Internal DVB-C/T/T2 that I borrowed from a friend, I have to return it.  I Wanted to make sure that my Aerial signal was Strong enough.  The Xtrend is Not seeing the USB Tuner.  If it is easier, I can remove (Internal)Tuner C, but the Xtrend still does not see the USB Tuner, I've already tried without Tuner C installed. 

 

Regards

 

Wizard

[Wizard1]

Hi WanWizard

 

I've removed the Internal Tuner © & just have the 2x DVB-S2 & the USB Tuner connected.

 

root@et8500:~# grep -r "" /proc/bus
/proc/bus/input/devices:I: Bus=0019 Vendor=14e4 Product=0000 Version=000c
/proc/bus/input/devices:N: Name="dreambox remote control (native)"
/proc/bus/input/devices:P: Phys=brcmstb/input0
/proc/bus/input/devices:S: Sysfs=/devices/virtual/input/input0
/proc/bus/input/devices:U: Uniq=
/proc/bus/input/devices:H: Handlers=kbd event0
/proc/bus/input/devices:B: PROP=0
/proc/bus/input/devices:B: EV=100013
/proc/bus/input/devices:B: KEY=400000 118fcf52 22a476e1 0 0 0 c 2818000 51b8 58514d01 9eb7c0 0 38000000 ffc
/proc/bus/input/devices:B: MSC=10
/proc/bus/input/devices:
/proc/bus/input/devices:I: Bus=0003 Vendor=0572 Product=0320 Version=0000
/proc/bus/input/devices:N: Name="DVBSky T330"
/proc/bus/input/devices:P: Phys=usb-ehci_hcd-1/ir0
/proc/bus/input/devices:S: Sysfs=/devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input1
/proc/bus/input/devices:U: Uniq=
/proc/bus/input/devices:H: Handlers=kbd event1
/proc/bus/input/devices:B: PROP=0
/proc/bus/input/devices:B: EV=100013
/proc/bus/input/devices:B: KEY=1000000 0 0 0 0
/proc/bus/input/devices:B: MSC=10
/proc/bus/input/devices:
/proc/bus/input/handlers:N: Number=0 Name=rfkill
/proc/bus/input/handlers:N: Number=1 Name=kbd
/proc/bus/input/handlers:N: Number=2 Name=leds
/proc/bus/input/handlers:N: Number=3 Name=mousedev Minor=32
/proc/bus/input/handlers:N: Number=4 Name=evdev Minor=64
/proc/bus/nim_sockets:NIM Socket 0:
/proc/bus/nim_sockets:  Type: DVB-S2
/proc/bus/nim_sockets:  Name: AVL6211
/proc/bus/nim_sockets:  Frontend_Device: 0
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 0
/proc/bus/nim_sockets:NIM Socket 1:
/proc/bus/nim_sockets:  Type: DVB-S2
/proc/bus/nim_sockets:  Name: AVL6211
/proc/bus/nim_sockets:  Frontend_Device: 1
/proc/bus/nim_sockets:  Has_Ouput: yes
/proc/bus/nim_sockets:  I2C_Device: 1
root@et8500:~#
 

[WanWizard]

So it doesn't see it. As long as this is not addressed, the rest is pointless.

 

Only I have no clue why it doesn't see it, your dmesg shows everything is fine.