Jump to content


Photo

Mutant HD 2400 restart spontaneous and hangs on loading udev


  • Please log in to reply
13 replies to this topic

#1 doglover

  • Rytec EPG Team
  • 16,974 posts

+635
Excellent

Posted 14 June 2021 - 20:24

The Mutant HD2400 has been restarting spontaneous.  This has happened 2 times in 2 weeks time.

This evening I was watching football (at least the pre match discussions) on één HD.  And the receiver restarted spontaneously.  (no recordings were active or scheduled)

The previous time  this happened was around last 2 june.

 

The receiver has been equipped with the development image. 

Th hung one was today from june 2, 20121

 

A spontaneous reboot is not that bad, but the receiver wont start through.  I hanged on the message:  Loading udev.

Tried to restart several times, but no change.  It hangs on the same udev message.

 

Because of this hung receiver, I could not look for a crash log.  But I doubt there is one, as no GSOD has been displayed.

 

However, I can reflash the receiver with the latest development image.  Restored also the autobackup with no problem.

After this the receiver works normal.

 

Anybody any idea why this can be happening?


Edited by doglover, 14 June 2021 - 20:25.

~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)

Synology NAS

Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #2 WanWizard

  • PLi® Core member
  • 68,301 posts

+1,718
Excellent

Posted 14 June 2021 - 20:33

Udev is the hardware device manager, but I can't think of any reason why it would "hang", even on some sort of hardware error.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #3 Pr2

  • PLi® Contributor
  • 6,046 posts

+256
Excellent

Posted 14 June 2021 - 20:40

Defective power supply probably, I had this with my brand new Solo 4K the seller had to send me a replacement part.

NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.

Wanna help with OpenPLi Translation? Please read our Wiki Information for translators

Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)

AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
 


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #4 doglover

  • Rytec EPG Team
  • 16,974 posts

+635
Excellent

Posted 15 June 2021 - 07:19

Udev is the hardware device manager, but I can't think of any reason why it would "hang", even on some sort of hardware error.

Do not misunderstand.  I do not know if this is the culprit.

On the screen this is the last thing shown.  (Loading udev - or something with udev).

The box then hangs.  Nothing happens.

 

The curious thing is that the box can be flashed with an USB-stick containing the image and backup.


~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)

Synology NAS

Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #5 rantanplan

  • PLi® Contributor
  • 1,756 posts

+81
Good

Posted 15 June 2021 - 10:15

Probably the 'Crash'-ShutDown destroyed the start files.
This happens again and again with Ubuntu.
Ubuntu can do this from console repair with fschk.
Surely there would be some way to get on the box to do something similar.

Don't know...
But a reflash is faster.

The question remains, why does it 'crash'


Edited by rantanplan, 15 June 2021 - 10:16.


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #6 doglover

  • Rytec EPG Team
  • 16,974 posts

+635
Excellent

Posted 15 June 2021 - 12:44

The question remains, why does it 'crash'

 

No idea.  In this case it was during normal watching of a sat channel. 

Of course something could be started in the background.  Although nothing was planned (EPGimport, autotimer, recording, cron job)

 

So memory full, would not be the first culprit.

Something near the end of its life?  (like Pr2 suggested - the power supply)


~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)

Synology NAS

Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #7 rantanplan

  • PLi® Contributor
  • 1,756 posts

+81
Good

Posted 15 June 2021 - 13:06

From the OE-Alliance forums you can reads about some mips receivers from the Zeus branch that are similar behavior that cannot be explained.
If an image from the previous branch was then installed, the same boxes ran again without any problems.
The hd2400 is one of them.
Difficult to say where the cause of the phenomenon is.
In that case I don't believe in gcc / glibc.
Mdev - udev is also unlikely.
Little has been heard of the problems in the Pli.
Maybe you can still test a 7.3 image and see if the same problems arise.



Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #8 WanWizard

  • PLi® Core member
  • 68,301 posts

+1,718
Excellent

Posted 15 June 2021 - 13:11

There are definitely issues in Zeus with glibc on MIPS, we've had them before. Erik can probably fill you in.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #9 doglover

  • Rytec EPG Team
  • 16,974 posts

+635
Excellent

Posted 15 June 2021 - 13:31

Maybe you can still test a 7.3 image and see if the same problems arise.

 

Problem is that several plug-ins do not work anymore on PLi 7.3 (and 8.0).

Like Foreca on 7.3 and service app on 8.0


Edited by doglover, 15 June 2021 - 13:32.

~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)

Synology NAS

Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #10 WanWizard

  • PLi® Core member
  • 68,301 posts

+1,718
Excellent

Posted 15 June 2021 - 13:51

Service app isnt the problem, ffmpeg is. Which has been fixed in develop some time ago,


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Pro (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #11 doglover

  • Rytec EPG Team
  • 16,974 posts

+635
Excellent

Posted 15 June 2021 - 14:01

Service app isnt the problem, ffmpeg is. Which has been fixed in develop some time ago,

And that is why I am using develop.


~~Rytec Team~~
Maxytec Multibox SE OpenPli (used as mediaplayer)
Mutant HD2400 OpenPli
Vu+ Duo OpenPli (backup)

Synology NAS

Sat: 13E, 19.2E, 23.5E and 28.2E
*Pli/Rytec EPG POWERED*


Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #12 rantanplan

  • PLi® Contributor
  • 1,756 posts

+81
Good

Posted 15 June 2021 - 19:25

https://sourceware.o...0q1/069189.html

 

possibly this?



Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #13 rantanplan

  • PLi® Contributor
  • 1,756 posts

+81
Good

Posted 15 June 2021 - 20:35

Have adjusted the patch so that it can be applied.
PullRequest is currently not answered.
Maybe you can still check it out.
greetings

Attached Files



Re: Mutant HD 2400 restart spontaneous and hangs on loading udev #14 Pr2

  • PLi® Contributor
  • 6,046 posts

+256
Excellent

Posted 16 June 2021 - 10:22

Foreca it is because the website layout has changed.


NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.

Wanna help with OpenPLi Translation? Please read our Wiki Information for translators

Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)

AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
 



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users