Jump to content


mimisiku

Member Since 30 Jul 2012
Offline Last Active Today, 05:10
*****

#1604618 Populaire ontvangers

Posted by mimisiku on 6 February 2024 - 17:20

Ik heb de VU+Ultimo 4K al jaren en mij is nooit wat raars opgevallen qua geluid...


#1590940 oscam.dvpapi M: 1817 0100:00006A

Posted by mimisiku on 19 December 2023 - 09:55

Ik heb OpenPli NB op een Xsarius Galaxy geplaatst met OScamCAK7. Met de benodigde keys krijg ik steevast 'card doesn't responds to CMD02/E command'. Heb dat ook gemeld. Ik heb ook de vraag gesteld om een CAK7 config voor M7 te mogen ontvangen (uiteraard zonder keys).. Ook daarop geen reactie.... Gebruik ik mijn eigen OScam binary dan werkt het prima..
Heb bij CMD02provider 01C0 ingevoerd...


#1564822 OpenPLi for Dreambox One

Posted by mimisiku on 4 September 2023 - 21:15

And with the demise of Dream Property GmbH and the loss of the official support servers it it highly questionable to buy a Dreambox nowadays!! The boxes have potential but without official support it is not a box to buy as a novice…




#1563182 VU+ Duo 4K SE and USB VU+ Turbo SE dvb-t stick

Posted by mimisiku on 29 August 2023 - 12:18

DVB-T2 in Germany is not weird, follows the H.265 HEVC standard as does the Netherlands, Belgium…




#1558908 Frage bezüglich Sky Deutschland

Posted by mimisiku on 15 August 2023 - 13:24

Nur noch mit illegale Mitteln…..




#1555768 VU+ Duo 4K SE and USB VU+ Turbo SE dvb-t stick

Posted by mimisiku on 2 August 2023 - 11:44

Have the same USB device. Never got it to work with OpenPli. The firmware is not available. Even with VTi this stick didn’t work (got recognised though). Even with disabling the internal DVB-C tuner in VTi it didn’t scan anything! Tried for a few months and then trew it in the bin. €60 down the drain… Completely and utterly unusable…..

 

I also remember that it required kernel 3.15+

 

The driver should be DVB T330




#1546327 Webif problem with Latest OScam 11719

Posted by mimisiku on 13 June 2023 - 09:41

Luckily I can build my own OScam binaries
Update is only necessary if something major has changed for a card you own. I had to update to 11717 for my sRG 7 card. But as stated, if your card runs fine you don't need to upgrade.


#1515175 Digitenne CI+

Posted by mimisiku on 30 January 2023 - 14:46

Tsja, niet zoals met een softcam en kaart. Een stuk trager, seconde of 1,5 a 2….




#1510951 Geen lege opnames meer.

Posted by mimisiku on 14 January 2023 - 10:12

En als je al tot de ontdekking komt dat het niet meer gaat wegens ruimtegebrek dan zorg je voor een oplossing. Dan ga je niet ijzeren Hendrik door. Maak een backup van de bestanden die je absoluut wenst te behouden en maak de movie directory leeg (en eventueel ook de vuilnisbak als je die geaktiveerd hebt)….




#1508862 Vu+ Duo 4K SE : H265 ?

Posted by mimisiku on 4 January 2023 - 12:26

The VU+Duo 4K SE can process H.265 just fine, Every 4K receiver has this capability…




#1505254 Bouquets en CH up en CH down

Posted by mimisiku on 23 December 2022 - 22:20

Bij Instellingen Channel + Channel- optie aanzetten.




#1501942 smartreader

Posted by mimisiku on 11 December 2022 - 20:52

I build with PCSC because I own one. Keep in mind that most (all) PCSC cardreaders operate at 3.57 or 3.69 Mhz and can’t change the clock frequency! This means that some card types can’t be used in these readers. Nagra cards mostly work, but Irdeto2 don’t (require 6 Mhz)




#1496593 Tuning problems after factory reset

Posted by mimisiku on 15 November 2022 - 19:17

Any news/change?




#1496149 Tuning problems after factory reset

Posted by mimisiku on 12 November 2022 - 20:54

Startup wizard started, installed tuners, performed channel scan. Picons, OScam & OScam config. Software update and reboot. OpenPli 8.3 running fine…

Detected something odd though. After reboot sound is intermittent for a few seconds. After a few channelswitchings sound is OK…




#1496105 Tuning problems after factory reset

Posted by mimisiku on 12 November 2022 - 18:24

I don’t understand… What did you throw away? Your receiver?

Oh wait… I think I understand that you misunderstood me…

What I meant is this…

You downloaded a zip file. You unpack this directly onto your FAT32 formated USB stick. The USB stick should now contain a directory /vuplus. In this directory you should see some files.. Shown us the files found in this /vuplus/ directory