foxbob

Also,after the reboot the box stopped loading.Not a single firmware is loaded.If the flash drive has firmware it offers to flash the receiver.For a very long time there is an inscription on the screen Updating rootfs and the inscription can be visible for about 1 hour.But the receiver still does not start.I made a start log via putty, but I can’t force start the firmware when I click on CTRL-C the log doesn't stop.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.02.01 19:24:03 =~=~=~=~=~=~=~=~=~=~=~=
 ю CPU 0123
BCM74450040
PRID74440040
v1.21
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-ALT
SHMOO 02010100 BLD:exported HW:hpf0_b1p3 V:2.1.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000396(918)
 temperature=00009bf0(39920)
 PV=00000354(852)
 MV=00000397(919)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0d9f4 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0d9f4 MEMSYS-1 @ f1180000 OK
DDR2: =@ ffe0e780 <= ffe0d9f4 MEMSYS-2 @ f1200000 OK
Sdram Scramble OTP = 0x00000001 
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f 
bfw_hash_locked = 0x00000000 
BFW key3 OK, BFW load OK
BFW v4.1.5
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  07089dd8
_ebss  070c9538
_end   070c9558
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 07089dd8 to 070c9538 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

[33;1m    ,/   [0m 
[33;1m  ,'/___,[0m BOLT v1.21 v1.21 LOCAL BUILD
[33;1m.'__  ,' [0m (2016-10-17 16:21:51 Vuplus team)
[33;1m   /,'   [0m Copyright (C) 2016 Broadcom
[33;1m  /'     [0m 
[0m
Board: ULTIMO4K
SYS_CTRL: product=7444, family=7445e0, strap=000005b6, 
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) 
otp @ 0xf0404034 = 0x00000001: moca2_disable(0x00000001) 
CPU: 4x B15 [420f00f3] 1503 MHz
SCB: 432 MHz
DDR0 @ 1200MHz, DDR1 @ 1200MHz, DDR2 @ 1200MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 21 possible causes)
CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages
[31;1mCS1: NAND: unrecognized ID: 0xffffff 0xffffffff[0m
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
RTS2: 0x1201004, 256 clients, ok
BOX MODE: 1
SPLASH: starting
SPLASH BMEM init @ 40000000
SPLASH BMEM init @ 80000000
SPLASH BMEM init @ c0000000
SPLASH: Old format file in flash. Use splash_create_flash_file to create newer format.
Loaded BMP: W=720 H=480
SPLASH: audio not present
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.918V, T=+41.381C, PV=0.852V, MV=0.919V, FW=30333278 [0.3.2.x]
check_tuner_version
i2c_readsw
Tuner Version [0x2]
LCD_Init Complete
boot device name [flash0.bolt]
waiting for usb...
usb: resetting device on bus 4 hub 1 port 1[J


USB: New high speed device connected to bus 4 hub 1 port 1[J


usb: resetting device on bus 4 hub 2 port 1[J


USB: New high speed device connected to bus 4 hub 2 port 1[J

usb: no driver found for 0a5c:bd27

usb: resetting device on bus 4 hub 2 port 2[J


USB: New full speed device connected to bus 4 hub 2 port 2[J


USB: Lower speed devices not supported under high speed hub[J


usb: resetting device on bus 5 hub 1 port 1[J


USB: New high speed device connected to bus 5 hub 1 port 1[J

usb: found Mass-Storage Device 8564:1000

USBMASS: Unit 0 connected[J

done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/ultimo4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/ultimo4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/ultimo4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/rootfs.tar.bz2......YES
Checking usbdisk0:/vuplus/ultimo4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/ultimo4k/kernel_auto.bin......YES
Checking usbdisk0:/vuplus/ultimo4k/reboot.update......YES
waiting for update key
readFrontKey 0x0
readFrontKey 0x0
readFrontKey 0x0
Skipping USB Update
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M vmalloc=600m bmem=608m@416m bmem=416m@1632m bmem=699m@2357m
Reading 4205024 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7628000)

32 bit direct boot...
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.28-1.12 (oe-user@oe-host) (gcc version 13.2.0 (GCC) ) #1 SMP Sun Jan 28 04:02:33 UTC 2024
[    0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: ULTIMO4K
[    0.000000] moving dtb from 0x0000000007628000 to 0x0000000000865248
[    0.000000] bmem: Reserved 630 MiB at 0x0000000018a00000
[    0.000000] bmem: Reserved 383 MiB at 0x0000000068100000
[    0.000000] bmem: Reserved 443 MiB at 0x00000000a4100000
[    0.000000] cma: Reserved 16 MiB at 0x0000000017000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] MCP: Enabling write pairing
[    0.000000] PERCPU: Embedded 8 pages/cpu @d81b0000 s8768 r8192 d15808 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 785660
[    0.000000] Kernel command line: root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M vmalloc=622m bmem=630m@394m bmem=383m@1665m bmem=443m@2625m
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 1600376K/3145728K available (5909K kernel code, 334K rwdata, 1872K rodata, 252K init, 189K bss, 1528968K reserved, 16384K cma-reserved, 1255412K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd8800000 - 0xff000000   ( 616 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd8200000   ( 386 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07a17d0   (7782 kB)
[    0.000000]       .init : 0xc07a2000 - 0xc07e1240   ( 253 kB)
[    0.000000]       .data : 0xc07e2000 - 0xc0835b58   ( 335 kB)
[    0.000000]        .bss : 0xc0835b60 - 0xc0865248   ( 190 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 94)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 96)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 48)
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[    0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[    0.000009] Switching to timer-based delay loop
[    0.000275] Console: colour dummy device 80x30
[    0.000295] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[    0.000303] pid_max: default: 32768 minimum: 301
[    0.000401] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.005847] CPU: Testing write buffer coherency: ok
[    0.006057] CPU0: update cpu_power 1024
[    0.006063] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.006186] Setting up static identity map for 0x5a5480 - 0x5a54d8
[    0.008545] CPU1: Booted secondary processor
[    0.008561] CPU1: update cpu_power 1024
[    0.008564] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.009177] CPU2: Booted secondary processor
[    0.009188] CPU2: update cpu_power 1024
[    0.009191] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.009776] CPU3: Booted secondary processor
[    0.009787] CPU3: update cpu_power 1024
[    0.009790] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.009840] Brought up 4 CPUs
[    0.009857] SMP: Total of 4 processors activated.
[    0.009861] CPU: All CPU(s) started in SVC mode.
[    0.010214] devtmpfs: initialized
[    0.013829] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[    0.014819] regulator-dummy: no parameters
[    0.015004] NET: Registered protocol family 16
[    0.017105] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.017892] cpuidle: using governor ladder
[    0.017898] cpuidle: using governor menu
[    0.020969] irq: no irq domain found for /rdb/interrupt-controller@f040a780 !
[    0.021123] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.025025] irq: no irq domain found for /rdb/interrupt-controller@f03e1a00 !
[    0.025297] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf040451b] registered
[    0.026057] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[    0.026212] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[    0.026356] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[    0.026492] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[    0.026643] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[    0.026782] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[    0.026932] syscon f1201004.syscon: regmap [mem 0xf1201004-0xf1201403] registered
[    0.027062] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[    0.027205] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[    0.027339] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[    0.027481] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[    0.027617] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[    0.028245] irq: no irq domain found for /rdb/interrupt-controller@f0417280 !
[    0.028785] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[    0.028934] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[    0.029236] No ATAGs?
[    0.029254] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.029260] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.029380] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[    0.044479] bio: create slab <bio-0> at 0
[    0.045168] SCSI subsystem initialized
[    0.045852] usbcore: registered new interface driver usbfs
[    0.045936] usbcore: registered new interface driver hub
[    0.046033] usbcore: registered new device driver usb
[    0.046157] Linux video capture interface: v2.00
[    0.046362] pps_core: LinuxPPS API ver. 1 registered
[    0.046366] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.046421] PTP clock support registered
[    0.046965] Advanced Linux Sound Architecture Driver Initialized.
[    0.047684] cfg80211: Calling CRDA to update world regulatory domain
[    0.048097] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[    0.048285] brcm-pci f0490000.pcie: adjusting to legacy (broken) pcie DT
[    0.148584] brcm-pci f0460000.pcie: link down
[    0.248885] brcm-pci f0490000.pcie: link down
[    0.248934] Switched to clocksource arch_sys_counter
[    0.249110] FS-Cache: Loaded
[    0.257862] thermal thermal_zone0: failed to read out thermal zone 0
[    0.257974] NET: Registered protocol family 2
[    0.258347] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.258374] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.258418] TCP: Hash tables configured (established 4096 bind 4096)
[    0.258483] TCP: reno registered
[    0.258490] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.258503] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.258622] NET: Registered protocol family 1
[    0.258804] RPC: Registered named UNIX socket transport module.
[    0.258808] RPC: Registered udp transport module.
[    0.258811] RPC: Registered tcp transport module.
[    0.258815] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.259038] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[    0.260291] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.261007] bounce pool size: 64 pages
[    0.261653] NFS: Registering the id_resolver key type
[    0.261679] Key type id_resolver registered
[    0.261683] Key type id_legacy registered
[    0.261694] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.261698] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.261846] FS-Cache: Netfs 'cifs' registered for caching
[    0.261904] Key type cifs.spnego registered
[    0.262062] fuse init (API version 7.22)
[    0.262203] msgmni has been set to 705
[    0.262870] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.262876] io scheduler noop registered
[    0.262880] io scheduler deadline registered
[    0.262905] io scheduler cfq registered (default)
[    0.263130] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[    0.293351] brcm-waketimer f0417580.waketimer: registered, with irq 260
[    0.293615] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.294978] f040ab00.serial: ttyS0 at MMIO 0xf040ab00 (irq = 107, base_baud = 5062500) is a 16550A
[    1.125022] console [ttyS0] enabled
[    1.128901] f040ab40.serial: ttyS1 at MMIO 0xf040ab40 (irq = 108, base_baud = 5062500) is a 16550A
[    1.138250] f040ab80.serial: ttyS2 at MMIO 0xf040ab80 (irq = 109, base_baud = 5062500) is a 16550A
[    1.150670] loop: module loaded
[    1.154419] ahci brcmstb-ahci.0: can't get clock
[    1.159132] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[    1.176949] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    1.185580] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part 
[    1.195201] scsi0 : ahci_platform
[    1.198845] scsi1 : ahci_platform
[    1.202397] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 62
[    1.210331] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 62
[    1.219482] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[    1.225862] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[    1.233184] m25p80 spi32766.0: found mx25l3255e, expected m25p80
[    1.239209] m25p80 spi32766.0: mx25l3255e (4096 Kbytes)
[    1.244469] 5 ofpart partitions found on MTD device spi32766.0
[    1.250314] Creating 5 MTD partitions on "spi32766.0":
[    1.255467] 0x000000000000-0x000000200000 : "flash0.bolt"
[    1.261552] 0x000000200000-0x000000210000 : "flash0.macadr"
[    1.267759] 0x000000210000-0x000000220000 : "flash0.nvram"
[    1.273882] 0x000000220000-0x000000230000 : "flash0.devtree"
[    1.280188] 0x000000000000-0x000000400000 : "flash0"
[    1.286847] libphy: Fixed MDIO Bus: probed
[    1.293303] libphy: unimac MII bus: probed
[    1.301652] unimac-mdio f0b403c0.mdio: Broadcom UniMAC MDIO bus at 0xfcb403c0
[    1.309589] brcm-systemport f04a0000.ethernet: Broadcom SYSTEMPORTv 1.00 at 0xfc4a0000 (irqs: 54, 55, TXQs: 32, RXQs: 1)
[    1.323164] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.329015] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.335454] xhci-brcm: xHCI BRCM driver
[    1.339377] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.345194] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[    1.353309] xhci-brcm f0471000.xhci_v2: irq 115, io mem 0xf0471000
[    1.360019] hub 1-0:1.0: USB hub found
[    1.363803] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    1.371067] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.376871] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[    1.385200] hub 2-0:1.0: USB hub found
[    1.388978] hub 2-0:1.0: 2 ports detected
[    1.393386] ehci-brcm: EHCI BRCM driver
[    1.397300] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[    1.403119] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[    1.421075] ehci-brcm f0470300.ehci_v2: irq 111, io mem 0xf0470300
[    1.432941] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.439601] hub 3-0:1.0: USB hub found
[    1.443379] hub 3-0:1.0: 1 port detected
[    1.447518] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[    1.453326] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[    1.471273] ehci-brcm f0470500.ehci_v2: irq 112, io mem 0xf0470500
[    1.482940] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.486952] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.487194] ata1.00: ATA-11: KINGSTON SUV400S37120G, 0C3J96R9, max UDMA/133
[    1.487198] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32)
[    1.487508] ata1.00: configured for UDMA/133
[    1.487718] scsi 0:0:0:0: Direct-Access     ATA      KINGSTON SUV400S 0C3J PQ: 0 ANSI: 5
[    1.488310] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[    1.488314] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.488489] sd 0:0:0:0: [sda] Write Protect is off
[    1.488548] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.548574] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.554017] hub 4-0:1.0: USB hub found
[    1.554359]  sda: sda1
[    1.555117] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.564787] hub 4-0:1.0: 1 port detected
[    1.568991] ehci-brcm f0480300.ehci_v2: EHCI Host Controller
[    1.574833] ehci-brcm f0480300.ehci_v2: new USB bus registered, assigned bus number 5
[    1.592817] ehci-brcm f0480300.ehci_v2: irq 117, io mem 0xf0480300
[    1.604940] ehci-brcm f0480300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.611617] hub 5-0:1.0: USB hub found
[    1.615393] hub 5-0:1.0: 1 port detected
[    1.619527] ehci-brcm f0480500.ehci_v2: EHCI Host Controller
[    1.625347] ehci-brcm f0480500.ehci_v2: new USB bus registered, assigned bus number 6
[    1.643296] ehci-brcm f0480500.ehci_v2: irq 118, io mem 0xf0480500
[    1.654939] ehci-brcm f0480500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.661617] hub 6-0:1.0: USB hub found
[    1.665396] hub 6-0:1.0: 1 port detected
[    1.669671] ohci-brcm: OHCI BRCM driver
[    1.673589] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[    1.677944] ata2: SATA link down (SStatus 0 SControl 300)
[    1.684825] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 7
[    1.692714] ohci-brcm f0470400.ohci_v2: irq 113, io mem 0xf0470400
[    1.753423] hub 7-0:1.0: USB hub found
[    1.757202] hub 7-0:1.0: 1 port detected
[    1.761342] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[    1.767163] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 8
[    1.775049] ohci-brcm f0470600.ohci_v2: irq 114, io mem 0xf0470600
[    1.836407] hub 8-0:1.0: USB hub found
[    1.840185] hub 8-0:1.0: 1 port detected
[    1.844322] ohci-brcm f0480400.ohci_v2: BRCM OHCI controller
[    1.850142] ohci-brcm f0480400.ohci_v2: new USB bus registered, assigned bus number 9
[    1.858022] ohci-brcm f0480400.ohci_v2: irq 119, io mem 0xf0480400
[    1.919402] hub 9-0:1.0: USB hub found
[    1.922957] usb 5-1: new high-speed USB device number 2 using ehci-brcm
[    1.929797] hub 9-0:1.0: 1 port detected
[    1.933945] ohci-brcm f0480600.ohci_v2: BRCM OHCI controller
[    1.939781] ohci-brcm f0480600.ohci_v2: new USB bus registered, assigned bus number 10
[    1.947750] ohci-brcm f0480600.ohci_v2: irq 120, io mem 0xf0480600
[    2.009418] hub 10-0:1.0: USB hub found
[    2.013285] hub 10-0:1.0: 1 port detected
[    2.017625] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.024174] ehci-pci: EHCI PCI platform driver
[    2.028712] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.034917] ohci-pci: OHCI PCI platform driver
[    2.039733] hub 5-1:1.0: USB hub found
[    2.043520] usbcore: registered new interface driver usb-storage
[    2.049571] hub 5-1:1.0: 4 ports detected
[    2.049717] mousedev: PS/2 mouse device common for all mice
[    2.050153] i2c /dev entries driver
[    2.050541] IR NEC protocol handler initialized
[    2.050544] IR RC5(x) protocol handler initialized
[    2.050545] IR RC6 protocol handler initialized
[    2.050547] IR JVC protocol handler initialized
[    2.050548] IR Sony protocol handler initialized
[    2.050551] IR RC5 (streamzap) protocol handler initialized
[    2.050552] IR SANYO protocol handler initialized
[    2.050554] IR MCE Keyboard/mouse protocol handler initialized
[    2.050907] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    2.051133] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    2.051397] sdhci: Secure Digital Host Controller Interface driver
[    2.051398] sdhci: Copyright(c) Pierre Ossman
[    2.051400] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.052521] mmc0: no vqmmc regulator found
[    2.052525] mmc0: no vmmc regulator found
[    2.082938] mmc0: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[    2.083231] hidraw: raw HID events driver (C) Jiri Kosina
[    2.087686] usbcore: registered new interface driver usbhid
[    2.087687] usbhid: USB HID core driver
[    2.150580] mmc0: BKOPS_EN bit is not set
[    2.156833] mmc0: new high speed MMC card at address 0001
[    2.158111] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB 
[    2.158202] mmcblk0boot0: mmc0:0001 4FPD3R partition 1 4.00 MiB
[    2.158295] mmcblk0boot1: mmc0:0001 4FPD3R partition 2 4.00 MiB
[    2.158376] mmcblk0rpmb: mmc0:0001 4FPD3R partition 3 512 KiB
[    2.161801]  mmcblk0: p1 p2 p3 p4
[    2.164652]  mmcblk0boot1: unknown partition table
[    2.165349]  mmcblk0boot0: unknown partition table
[    2.205977] TCP: cubic registered
[    2.209326] NET: Registered protocol family 17
[    2.213948] Distributed Switch Architecture driver version 0.1
[    2.219855] sys0[0]: detected a Broadcom Starfighter 2 switch
[    2.225857] Starfighter 2 top: 4.00, core: 2.00 base: 0xfcb00000, IRQs: 56, 57
[    2.233250] libphy: dsa slave smi: probed
[    2.293937] f0b403c0.mdio:05: Broadcom BCM7445 PHY revision: 0x10, patch: 3
[    2.508043] usb 5-1.1: new high-speed USB device number 3 using ehci-brcm
[    2.528036] attached PHY at address 5 [Broadcom BCM7445]
[    2.533795] net eth0: PHY already attached
[    2.538086] Key type dns_resolver registered
[    2.542418] Registering SWP/SWPB emulation handler
[    2.547658] regulator-dummy: disabling
[    2.554625] ALSA device list:
[    2.557608]   No soundcards found.
[    2.561808] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[    2.675055] usb 5-1.2: new full-speed USB device number 4 using ehci-brcm
[    2.947980] usb 6-1: new high-speed USB device number 2 using ehci-brcm
[    3.069846] usb-storage 6-1:1.0: USB Mass Storage device detected
[    3.076253] scsi2 : usb-storage 6-1:1.0
[    3.151117] random: nonblocking pool is initialized
[    4.082636] scsi 2:0:0:0: Direct-Access     JetFlash Transcend 8GB    1.00 PQ: 0 ANSI: 6
[    4.091804] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    4.092226] sd 2:0:0:0: [sdb] 15433728 512-byte logical blocks: (7.90 GB/7.35 GiB)
[    4.092593] sd 2:0:0:0: [sdb] Write Protect is off
[    4.092971] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[    4.121991]  sdb: sdb1 sdb2
[    4.126966] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   13.535942] mmc0: Timeout waiting for hardware interrupt.
[   13.543353] ------------[ cut here ]------------
[   13.547987] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   13.560171] Modules linked in:
[   13.563243] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.28-1.12 #1
[   13.569710] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   13.577469] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   13.584705] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   13.592810] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   13.601608] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   13.610408] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   13.619118] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   13.628003] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   13.636885] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   13.645072] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   13.652390] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   13.659448] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   13.667029] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   13.674518] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   13.679575] 3f40:                                                       ffffffed 179d1000
[   13.687761] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   13.695947] 3f80: c07d5628 00000000 d81b0fe0 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   13.704135] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   13.711542] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   13.719733] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   13.727921] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   13.734108] ---[ end trace 70c38a30b36c9d64 ]---
[   13.740836] mmcblk0: error -110 transferring data, sector 73536, nr 16, cmd response 0x0, card status 0x400d00
[   13.750862] end_request: I/O error, dev mmcblk0, sector 73536
[   13.756624] Buffer I/O error on device mmcblk0p4, logical block 232
[   13.762904] lost page write due to I/O error on mmcblk0p4
[   13.768322] end_request: I/O error, dev mmcblk0, sector 73544
[   13.774081] Buffer I/O error on device mmcblk0p4, logical block 233
[   13.780361] lost page write due to I/O error on mmcblk0p4
[   23.807947] mmc0: Timeout waiting for hardware interrupt.
[   23.815355] ------------[ cut here ]------------
[   23.819982] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   23.832164] Modules linked in:
[   23.835235] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W    3.14.28-1.12 #1
[   23.842644] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   23.850401] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   23.857634] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   23.865736] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   23.874534] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   23.883332] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   23.892042] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   23.900925] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   23.909807] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   23.917993] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   23.925311] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   23.932369] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   23.939948] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   23.947437] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   23.952493] 3f40:                                                       ffffffed 179d1000
[   23.960678] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   23.968864] 3f80: c07d5628 00000000 00000000 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   23.977052] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   23.984458] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   23.992645] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   24.000830] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   24.007015] ---[ end trace 70c38a30b36c9d65 ]---
[   24.013728] mmcblk0: error -110 transferring data, sector 73672, nr 8, cmd response 0x0, card status 0x400d00
[   24.023661] end_request: I/O error, dev mmcblk0, sector 73672
[   24.029420] Buffer I/O error on device mmcblk0p4, logical block 249
[   24.035699] lost page write due to I/O error on mmcblk0p4
[   34.079953] mmc0: Timeout waiting for hardware interrupt.
[   34.087360] ------------[ cut here ]------------
[   34.091985] WARNING: CPU: 0 PID: 0 at /usr/src/debug/linux-vuplus/3.14.28/drivers/mmc/host/sdhci.c:994 sdhci_send_command+0x798/0xf0c()
[   34.104168] Modules linked in:
[   34.107237] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W    3.14.28-1.12 #1
[   34.114645] [<c0015f70>] (unwind_backtrace) from [<c0011e1c>] (show_stack+0x10/0x14)
[   34.122400] [<c0011e1c>] (show_stack) from [<c059cc54>] (dump_stack+0x6c/0x7c)
[   34.129632] [<c059cc54>] (dump_stack) from [<c059abc0>] (warn_slowpath_common+0x68/0x84)
[   34.137734] [<c059abc0>] (warn_slowpath_common) from [<c0022a7c>] (warn_slowpath_null+0x1c/0x24)
[   34.146532] [<c0022a7c>] (warn_slowpath_null) from [<c045eeb0>] (sdhci_send_command+0x798/0xf0c)
[   34.155329] [<c045eeb0>] (sdhci_send_command) from [<c0460cbc>] (sdhci_timeout_timer+0x74/0xb8)
[   34.164039] [<c0460cbc>] (sdhci_timeout_timer) from [<c002c9b4>] (call_timer_fn.isra.0+0x20/0x7c)
[   34.172921] [<c002c9b4>] (call_timer_fn.isra.0) from [<c002cb5c>] (run_timer_softirq+0x14c/0x218)
[   34.181803] [<c002cb5c>] (run_timer_softirq) from [<c0026e78>] (__do_softirq+0x10c/0x2a8)
[   34.189990] [<c0026e78>] (__do_softirq) from [<c00272a8>] (irq_exit+0xe0/0x118)
[   34.197307] [<c00272a8>] (irq_exit) from [<c000f7e0>] (handle_IRQ+0x44/0x90)
[   34.204365] [<c000f7e0>] (handle_IRQ) from [<c000858c>] (gic_handle_irq+0x2c/0x5c)
[   34.211943] [<c000858c>] (gic_handle_irq) from [<c0012840>] (__irq_svc+0x40/0x50)
[   34.219432] Exception stack(0xc07e3f58 to 0xc07e3fa0)
[   34.224487] 3f40:                                                       ffffffed 179d1000
[   34.232673] 3f60: c07eb3ec 00000000 c07e2000 c05a808c c0829de4 c07ea444 c06bc044 00000001
[   34.240858] 3f80: c07d5628 00000000 d81b0fe0 c07e3fa0 c000fb04 c000fafc 60000113 ffffffff
[   34.249046] [<c0012840>] (__irq_svc) from [<c000fafc>] (arch_cpu_idle+0x2c/0x38)
[   34.256452] [<c000fafc>] (arch_cpu_idle) from [<c005feac>] (cpu_startup_entry+0x74/0x138)
[   34.264639] [<c005feac>] (cpu_startup_entry) from [<c07a2bb8>] (start_kernel+0x40c/0x418)
[   34.272825] [<c07a2bb8>] (start_kernel) from [<00008084>] (0x8084)
[   34.279010] ---[ end trace 70c38a30b36c9d66 ]---
[   34.285718] mmcblk0: error -110 transferring data, sector 81952, nr 8, cmd response 0x0, card status 0x400d00
[   34.295655] end_request: I/O error, dev mmcblk0, sector 81952
[   34.301416] Buffer I/O error on device mmcblk0p4, logical block 1284
[   34.307783] lost page write due to I/O error on mmcblk0p4