Jump to content


Photo

Subtitle disapear when fastforward/back forward


  • Please log in to reply
30 replies to this topic

#1 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 11:41

Hello,

I have got a problem on my openPli 9.0 (upgraded to lattest so correction here).
 

Context:
Vu+ solo SE V2 updated to the lattest stable version (update done to day)
Record TNT T2 (1080P)

 

When i play record and fast forward, or back forward a time (for exemple to jump the publicity) when i play back, subtitle does not come again. Nothing appear. On my previous rom OpenATV 5.1, it alwas come back after something like 2s after the ui disapear.
But here, If i jump to an epg marker that delimit the start of new program, it come back again.
If i stop, then play again to come back in the record and enable subtitle, of course it works.

 

Is there something i could do to solve this problem?
Thank's



Re: Subtitle disapear when fastforward/back forward #2 littlesat

  • PLi® Core member
  • 57,190 posts

+699
Excellent

Posted 2 November 2024 - 11:48

I cannot confirm it here with subtitles… And when you use step skip instead fast forward and backward?

Edited by littlesat, 2 November 2024 - 11:48.

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: Subtitle disapear when fastforward/back forward #3 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 11:59

Does "step skip" is not the case i wrote there: "If i jump to an epg marker that delimit the start of new program, it come back again." with the key > on my remote ?
I did not find other key on my remote to "jump". cross right key does the same then fastforward button.


Edited by linus, 2 November 2024 - 12:01.


Re: Subtitle disapear when fastforward/back forward #4 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 13:13

Ok, i found the jump key, it's 1/3 4/5 7/9.
So if i use this key, it works immediatly, so the problem is just with fast and back forward.



Re: Subtitle disapear when fastforward/back forward #5 40H3X

  • Forum Moderator
    PLi® Contributor
  • 5,957 posts

+191
Excellent

Posted 2 November 2024 - 15:07

Just don't use them/ only use skip instead , please read https://wiki.openpli...weaks#Skip_time


Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K  - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport

---------------------------------------------------------------------------------------------------------------------------------------

Remember: Upvote with the rep_up.png button for any user/post you find to be helpful, informative, or deserving of recognition!

---------------------------------------------------------------------------------------------------------------------------------------

Many answers to your question can be found in our new and improved wiki

Note: I do not provide support via PM !.


Re: Subtitle disapear when fastforward/back forward #6 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 15:31

Yep i found that and already found the key as written before, but that does not explain why it was perfectly working before in an old openAtv and not in openPli 9.0.

If the bug could be corrected it would be better.

 

Just to explain why: the vu+ are used my by parents, so forward/backward is a notion that exist since a lot of time, even if they could understand jump key, you could not say that push on 6/9 key is something intuitive and remember every time how much time jump key does is not something easy for somebody that are more then 70 year old. :o

And is somebody external come and watch a record, samething, you should explain again where as forward/backward is internatial and have been exist since a lot of time.


Edited by linus, 2 November 2024 - 15:32.


Re: Subtitle disapear when fastforward/back forward #7 WanWizard

  • PLi® Core member
  • 70,552 posts

+1,813
Excellent

Posted 2 November 2024 - 16:27

You still haven't understood what I have been telling you?

 

You are making assumptions that are not correct: you can not compare the behaviour of driver A with stream X, which driver B and stream Y, and then say "the first combination used to work, so the second must work now", it is simply not true.

 

And I doubt there is a box that has a working fast-forward / fast reverse, given the fact you're not dealing with an analog tape you can speed up or reverse, you're dealing with a compressed MPEG data in a stream with 188 byte packages containing different frame types.

 

You can only reliably jump from I-frame to I-frame, and whether or not you have them, how many, and how they are spaced in the stream, depends on the settings of the MPEG compressor at the source. This is what the jump keys do.

 

Fast forward / Reverse jump to arbitrary locations in the stream, landing on most likely not an I-frame, which means a very complete operation must follow to construct something of an image at that point (apart from I-frames, MPEG frames are delta's on the previous frame, so not a complete picture).

 

Most drivers are not very good at this complex operation, which is made worse if there is corruption in the MPEG stream, which could mean assumptions the drivers make about the stream may not be correct.

 

For your parents, you could update the keymap, and map " <<  " to the 1 key, and " >> " to the 3 key? Downside is that it is only one jump, it doesn't keep jumping until you press play again. I understand that jumping is something new to learn, but it is the technology that is limiting it, not the software.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Subtitle disapear when fastforward/back forward #8 WanWizard

  • PLi® Core member
  • 70,552 posts

+1,813
Excellent

Posted 2 November 2024 - 16:30

p.s. nobody is stopping you from downloading drivers from 2017 and installing those into a current image, that should work fine ( apart from the fact you'll miss any bug fixes since 2017, which might introduce other issues ).

 

These are all the drivers for the Solo SE  ( this is what we're talking about, yes? ) ever released:

[root@openpli-dist vuplus]# ls -l vuplus-dvb-modules-vusolose-3.13.5-201*
-rw-r--r--. 1 1002 1002 4034235 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20141201.tar.gz
-rw-r--r--. 1 1002 1002 4034508 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20141231.tar.gz
-rw-r--r--. 1 1002 1002 4035400 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20150109.tar.gz
-rw-r--r--. 1 1002 1002 4150432 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20150317.tar.gz
-rw-r--r--. 1 1002 1002 4152722 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20150403.tar.gz
-rw-r--r--. 1 1002 1002 4154663 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20150511.tar.gz
-rw-r--r--. 1 1002 1002 4169316 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20150623.tar.gz
-rw-r--r--. 1 1002 1002 4171552 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20151117.tar.gz
-rw-r--r--. 1 1002 1002 4171491 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20151201.tar.gz
-rw-r--r--. 1 1002 1002 4429534 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20161228.tar.gz
-rw-r--r--. 1 1002 1002 4431931 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20170522.tar.gz
-rw-r--r--. 1 1002 1002 4431935 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20170822.tar.gz
-rw-r--r--. 1 1002 1002 4432113 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20171107.tar.gz
-rw-r--r--. 1 1002 1002 4437267 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20171121.tar.gz
-rw-r--r--. 1 1002 1002 4437347 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20171127.tar.gz
-rw-r--r--. 1 1002 1002 4437170 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20171204.tar.gz
-rw-r--r--. 1 1002 1002 4525496 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20180220.tar.gz
-rw-r--r--. 1 1002 1002 4529502 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20180319.tar.gz
-rw-r--r--. 1 1002 1002 4530286 Oct 28 18:47 vuplus-dvb-modules-vusolose-3.13.5-20190429.tar.gz

You can find the version you're using on the box, menu - information - about.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Subtitle disapear when fastforward/back forward #9 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 17:50

Just to be sure we are talking on the same thing. I am not talking about the previous pb i was talking in the over thread. (in the corrupted file).

Here i am just talking about the lost of the subtitle when playing a record and if you do a fast forward/back . No problem for audio or video forward/back. Just the subtitle disappear, and it's the case in all the record.
if you pause play, it change nothing, but If i just make a "jump" in the video ( every jump key ) without exit the video, it immediately come back.
For you it's related to driver?

 

"you can not compare the behavior of driver A with stream X, which driver B and stream Y"
You do not understand me or i do not explain well.
I took the record i have done with the OpenPli 9.0, play it with OpenAtv 5.1 and... And subtitle works perfectly.
So the sentense is:

I compare the behaviour of driver "A with a record X" with "driver B and same record X"

But i have try the opposite: play a record made with openAtv 5.1 on OpenPli 9.0, and the result is the same, it works perfectly on openAtv 5.1 where as i lost the subtitle when fast forward on openPli 9.0.

 

If you are totally sure that it's a driver problem and could not be other things (like a rendering bug/problem or video playing in enigma or the skin used) then i have got my answer and as you said i could test older driver to see if it' change.
But if it's not related to driver/hardware, i would have found a good idea to solve a problem that was not here before bug.

 

 

For your parents, you could update the keymap, and map " <<  " to the 1 key, and " >> " to the 3 key? Downside is that it is only one jump, it doesn't keep jumping until you press play again. I understand that jumping is something new to learn, but it is the technology that is limiting it, not the software.

 

I try to take a look, but on the hotkey did not find any possibility to map a key "jump fonction" if i am not wrong.
In openATV i could use "long press" on right/left to move in the video time so jump to a position (that's easy to understand where you are and what you are doing), but here i do not find this functionality or mapping possibility, it could have been a solution to solve the problem too but if i am not wrong i do not find this possibility in openPli 9.0.

 

 

 

 

And I doubt there is a box that has a working fast-forward / fast reverse, given the fact you're not dealing with an analog tape you can speed up or reverse, you're dealing with a compressed MPEG data in a stream with 188 byte packages containing different frame types.

Just for information, as i said, it was the case for OpenAtv 5.1 on this hardware, but it's the case of a lot of commercial TNT player/sat player that could record in TS (even if they are more limited, or buggy in some over point) and of course, it's the case of a lot of video player (like mpv/vlc/mplayer) that could play exactly this record with subtitle and fast forward with no problem so even if it's complicated and could be source of problem it seems it's not impossible.
 



Re: Subtitle disapear when fastforward/back forward #10 WanWizard

  • PLi® Core member
  • 70,552 posts

+1,813
Excellent

Posted 2 November 2024 - 18:53

Restoring old drivers on a 9.0-release image is not that complex ( assuming you can handle a linux commandline ), so it can easily be tested if it is a regression in the drivers or not.

 

As to subtitles, whether they are TXT or DVB image subtitles, they are seperate "tracks" in the MPEG stream ( packets with a seperate ID, multiplexed into the MPEG stream ). They should have a timing track with them (like the old timing track on a movie reel ), which is used to synchronize video and subs. But some providers make a mess of things. If the timing track is missing or wrong, Enigma will try to show the subtitles when they are read from the stream, without buffering and timing.

 

From a technical point of view, fast forward or reverse is implemented in the drivers ( and we don't have the source, so no idea how ), but a jump is implemented in Enigma, it essentially stops the playback, does a seek in the video stream looking for the next I-frame the defined number of seconds in the future, and then restarts playback of the stream, not from byte 0 of the file, but from the point found. Which makes it a lot more reliable, as it is essentially identical to starting the playback of a recording.

 

As explained before, how the stream is encoded plays a massive part in if and how this works. If for example the compression is so heavy that there is only an I-frame every 5 minutes, a 15sec jump will actually jump 5 minutes forward, and also the stream is much more susceptible to corruption ( which causes blocks or parts of the video standing still ) because it needs an I-frame to re-assemble a complile frame from all delta frames.

 

I can imagine ( but not prove ) that drivers that were designed on the assumption that there are I-frames every few seconds may run into conditions not expected by the developers when I-frames are much more spaced out...


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Subtitle disapear when fastforward/back forward #11 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 2 November 2024 - 19:02

Thank's for the explanation and play/pause are in driver too like fast forward or reverse?

 

No problem for cmd line. It's more time that is needed.
Do you think that i could try the modern driver in the old openATV to see if the fast/back pb appear?

If i got time/Possibility i will try to test OpenATV 7.4 or other recent rom with this same record to see if i got the same pb with subtitle to see if all the rom got the problem or not.

 

I did not found a way to replace the >> and << with "jump" function. :/


Edited by linus, 2 November 2024 - 19:04.


Re: Subtitle disapear when fastforward/back forward #12 WanWizard

  • PLi® Core member
  • 70,552 posts

+1,813
Excellent

Posted 3 November 2024 - 14:43

Yes, you can install any driver version in any image version, VU+ has never done a kernel update, for any box.

 

Let me know if you want instructions.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Subtitle disapear when fastforward/back forward #13 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 3 November 2024 - 14:51

Ok, so i made test to see if all recent rom got "this bug".
I took the same record for all the rom tested, in the same external hardrive in the same condition (Audio VO + Subtitle).
In OpenATV i install the PLi-FullNightHD skin that is on openPli (because i like it) and enable it to be sure that it could not be a skin problem.

* In Openpli 8.3 or 9.0 ==> pb with fastforward/back like written here.

* In OpenATV 7.4, so the latest version ==> No problem, subtitle in this same record (and all i try) works perfectly, i could fastforward even at *128 with no problem, when i play it's back again in no more then 3s.
So that confirm that definitively this bug is not here for OpenATV even in the latest version, and yes i took a look of the driver in openAtv it's 2019 like in openPli.

 

I try to change settings DVB settings in OpenPLi and OpenATV to see if one setting could change that, but nothing change. (transparency or dvb settings, size etc), it always work in OpenATV whereas it does not work on OpenPli.
It's not a big problem but that's a proof that there is solution to make it work on vu+ with modern Enigma2.
 

 

 

Yes, you can install any driver version in any image version, VU+ has never done a kernel update, for any box.

 

Let me know if you want instructions.

Thank you, i will take a look but normally the test prouve that it's not a pb driver.


Edited by linus, 3 November 2024 - 14:52.


Re: Subtitle disapear when fastforward/back forward #14 littlesat

  • PLi® Core member
  • 57,190 posts

+699
Excellent

Posted 3 November 2024 - 15:20

Openatv allows hacks and work-a-rounds with if vu+ then do something else style. We always tried the manufacturer does solve it to avoid it. And thanks to they accept such hacks it might work for them…

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: Subtitle disapear when fastforward/back forward #15 WanWizard

  • PLi® Core member
  • 70,552 posts

+1,813
Excellent

Posted 3 November 2024 - 15:21

Which hack or workaround are you referring to? Or is this assumption?


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Subtitle disapear when fastforward/back forward #16 littlesat

  • PLi® Core member
  • 57,190 posts

+699
Excellent

Posted 3 November 2024 - 17:50

When it is working in their image they somehow have to but to find in in their commits it is not easy to find…. As far I now understand it is not only driver related. Also eg in vti they worked around drivers.

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: Subtitle disapear when fastforward/back forward #17 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 3 November 2024 - 19:10

Normally they are using the enigma2 repo no?
Where does the hack could be? Something that is patched during the build?

I am trying to take a look of the openATV repo, but for the moment it's not easy.



EDIT: yes there are specificity for hardware in some source code like here:
https://github.com/o...dvb/decoder.cpp

( #ifdef DREAMBOX)

But this specificty are here for openpli too:
https://github.com/O...dvb/decoder.cpp

 

Whitch source code could be different?


Edited by linus, 3 November 2024 - 19:16.


Re: Subtitle disapear when fastforward/back forward #18 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 6 November 2024 - 21:03

Just to have an idea, do you know in witch part it could be?

I see difference in lib/dvb/subtitle.cpp,
In openatv 7.4 (so a lot of change from that) they use:
#include <lib/base/esettings.h>

 

whereas openpli use:
#include <lib/base/nconfig.h>

 

But that should not explain the reason because it works on openatv 5.1 and in 5.3 it was already the same sinclude then you.

 

There is a lot of change in lib/dvb/decoder.cpp too but not sure that could explain too, they use #include <lib/base/nconfig.h> in 5.3 and
#include <lib/base/esimpleconfig.h> but in openPli there is not such use of nconfig, not sure that could explain some difference.

At this point i do not know where to watch and what is used on DvB subtitle in record.
 



Re: Subtitle disapear when fastforward/back forward #19 Jork

  • Senior Member
  • 825 posts

+13
Neutral

Posted 6 November 2024 - 23:45

I recommend to use e2iplayer for this local media. It has a more sophisticated function in a FF and REW (step) search bar. If i use standard player as it is i don not speed up beyond 8x. I get problems with sync because of STB performance. This is all depending on hardware.

Re: Subtitle disapear when fastforward/back forward #20 linus

  • Senior Member
  • 55 posts

0
Neutral

Posted 9 November 2024 - 11:20

Hello, are you sure about "e2iplayer"?

I could not find something recent about it, and when i search information it's about iptv, and i do not use iptv.

Do you want to talk of exteplayer3 that i could use with serviceapp?

 

 

 

For the moment i took time to check difference between openatv 7.4 and 5.3 (as 5.1 is not in the repo) and openpli 9.0, and do not found anything relevant.
I take a look only in enigma2 repo for the moment. I do not see any hack for vu+, the only "hack" that they are is for dreambox, and some are in openpli too.

 

I check in vis files for the moment (related to fastforward/fastforwardtrick/play/subtitle):
lib/dvb/decoder.cpp
lib/dvb/dvb.cpp
lib/dvb/subtitle.cpp

 

lib/service/servicedvb.cpp

 

But i am not totally sure it should be in such files.
There is no documentation, no comment to find how everything works. :(
But even it could be related to default settings or choosen lib and i would not see it.
If someone could help me to says in witch files i should take a look.


Edited by linus, 9 November 2024 - 11:20.



7 user(s) are reading this topic

0 members, 7 guests, 0 anonymous users