Hello, I am Hotbird 13. OpenATV 7.4 Hotbird does not show channels. How should the tuner settings be? There is only one cable at home. The satellite device does not show Turksat and Hotbird. It says signal is zero.
signal zero
Started by eskehacettepe123, 27 Dec 2024 19:28
7 replies to this topic
Re: signal zero #2
-
- PLi® Core member
- 70,996 posts
+1,837
Excellent
Posted 27 December 2024 - 20:09
Why ask here? Ask on the ATV forum instead.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Re: signal zero #3
-
- Senior Member
- 29 posts
0
Neutral
Posted 27 December 2024 - 20:17
but it doesn't work, it says signal is zero
Re: signal zero #4
-
- Senior Member
- 29 posts
0
Neutral
Posted 27 December 2024 - 20:48
oh it doesn't work
Re: signal zero #5
-
- Senior Member
- 29 posts
0
Neutral
Re: signal zero #6
-
- Forum Moderator
PLi® Core member - 14,959 posts
+488
Excellent
Posted Yesterday, 09:23
It is the same if you ask LG questions about your problems with a Samsung TV.
You should ask the maker of the TV, in this case the maker who made the image for your STB which is openatv, so you should ask the question there instead of here.
Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....
On the edge of the abyss, a step forward is not always progress....
Hardware: 2x Daily used Vu+ Ultimo 4K - Vu+ Duo 4K SE and a lot more.... - VisioSat BiBigsat - Jultec Unicable Multiswitch 4 positions: 19.2/23.5/28.2 East - Diseqc motorized flatdish antenna
Software : HomeBuild OpenPLi Develop and Scarthgap builds, local cards driven by OsCam
Press the 
button on the buttom right of this message 
Have you tried our wiki yet? Many answers can be found in our OpenPLi wiki
Re: signal zero #7
-
- Senior Member
- 674 posts
+62
Good
Posted Yesterday, 11:49
Hi.
Personally, I don't think there's a bug in Enigma2 (OpenATV or OpenPLi). The questioner probably overlooked that it's on the PLi forum and not the ATV forum 
.
Anyway... the problem can be, for example, when transferring a backed-up configuration of tuned satellite channels from another Linux set-top box, where a different type of LNB converter was used. This happens to me often, for example, if ports A and B are on the other side of some LNBs. Then the DiSEqC switch understandably doesn't work correctly, because it expects a different satellite on port A than in the previous setting from the previous set-top box (with a different LNB).
I recommend first checking and re-setting the tuner (LNB) in the set-top box. Then start tuning the channels.
The "0" signal does not necessarily mean a tuner error. It could be a non-existent channel or a non-existent transponder (so it's without a signal).
The connection strength can also be tested directly in the tuner configuration - this applies to both PLi and ATV. There is also a signal finder function in the MENU for this purpose, which shows the signal strength on various transponders (frequencies), which the user switches himself in the set-top box.
If you are sure that there is no error in what I have listed, then it could be an error on the electrical/HW level. So the error could be in a poorly prepared and poorly connected coaxial cable... and so on.
Re: signal zero #8
-
- Senior Member
- 201 posts
+4
Neutral
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
