2047 replies to this topic

[momi133]

Now I run /usr/local/e2/e2pc.sh and start enigma2 and show an image but close and start again!

 

root@mamad-VPCF133FX:/usr/local/e2/bin# ./e2pc.sh
mv: cannot stat '/media/hdd/*.log': No such file or directory
./e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]

 

what do I do?
 

[1455]

I can not answer for several days.
Without /dev/dvb/frontend0 the dvb receive will not work. Mediaplayer and iptv only.  

https://forums.openp...ndpost&p=885829
https://forums.openp...ndpost&p=886507

Edited by 1455, 1 August 2018 - 12:42.

[momi133]

dvb card driver was installed successfully!

 

mamad@mamad-VPCF133FX:~$ dmesg | grep dvb  
[ 1957.580453] dvb-usb: TurboSight TBS 5520SE successfully deinitialized and disconnected.
[ 2042.220561] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[ 2042.220566] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[ 2042.378136] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[ 2042.378355] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 2042.378726] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[ 2042.379914] dvb-usb: MAC address reading failed.
[ 2042.886508] dvb-usb: no frontend was attached by 'TurboSight TBS 5520SE'
[ 2042.887326] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.
[ 2042.888175] dvb-usb: TurboSight TBS 5520SE successfully deinitialized and disconnected.
[ 2044.237059] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[ 2044.237065] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[ 2044.393420] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[ 2044.393788] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 2044.394082] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[ 2044.620093] dvb-usb: MAC address: 00:22:ab:c0:45:33
[ 2044.677452] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.

 

 

but I can't run e2pc.sh because of error in previous post! please help me!

 

thanks a lot!

[momi133]

I can not answer for several days.
Without /dev/dvb/frontend0 the dvb receive will not work. Mediaplayer and iptv only.  

https://forums.openp...ndpost&p=885829
https://forums.openp...indpost&p=88650

 

coming up of enigma2pc is important firstly!

 

I run ./autostart.sh but didn't happen anything!

 

thanks.

[momi133]

Now I run /usr/local/e2/e2pc.sh and start enigma2 and show an image but close and start again!

 

root@mamad-VPCF133FX:/usr/local/e2/bin# ./e2pc.sh
mv: cannot stat '/media/hdd/*.log': No such file or directory
./e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]
/usr/local/e2/bin/e2pc.sh: 11: [: missing ]

 

what do I do?
 

 

Please help me to solve this error!

 

Also dvb card driver was installed successfully! but ca0 doesn't appear!

 

in this post @Mounir67 said about  dvbsotwareca.ko !  what's your idea about thi post?

 

https://forums.openp...ndpost&p=889198 

 

Posted 20 May 2018 - 20:17

open terminal 

go to your directory :     /enigma2pc-6.2/dvbsoftwareca/

and type : sudo insmod dvbsotwareca.ko 

 

and check if ca0 if it is present with this command :

 ls -l  /dev/dvb/*

 

 

[1455]

Attention. Don't update pulseaudio to version 12.2 in Ubuntu-18.04!
For me pulseaudio-desktop doesn't start by autostart. If you start manually, there is no sound in the Enigma2.

[momi133]

Attention. Don't update pulseaudio to version 12.2 in Ubuntu-18.04!
For me pulseaudio-desktop doesn't start by autostart. If you start manually, there is no sound in the Enigma2.

 

I installed Ubuntu 16.04 and e2pc is successfully installed!

 

but e2pc detect just  adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)

 

and doesn't show adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)! actually satellite tuner ( DVB-S/S2/S2X) is not detected!

 

I just need the satellite tuner( DVB-S/S2/S2X) and DVB-T/T2/C/C2/ISDB-T is not important!

 

please help me!

 

Please see this commands:

 

 

 

# ls -l  /dev/dvb/*
total 0
crw-------  1 root root  236, 0 Aug  9 07:38 ca0
crw-------  1 root root  236, 1 Aug  9 07:38 ca1
crw-rw----+ 1 root video 212, 0 Aug  9 07:32 demux0
lrwxrwxrwx  1 root root      24 Aug  9 07:38 demux1 -> /dev/dvb/adapter0/demux0
crw-rw----+ 1 root video 212, 1 Aug  9 07:32 dvr0
lrwxrwxrwx  1 root root      22 Aug  9 07:38 dvr1 -> /dev/dvb/adapter0/dvr0
crw-rw----+ 1 root video 212, 3 Aug  9 07:32 frontend0
crw-rw----+ 1 root video 212, 4 Aug  9 07:32 frontend1
crw-rw----+ 1 root video 212, 2 Aug  9 07:32 net0

 

 

 

# dmesg

[  213.021306] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[  213.036286] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[  213.036289] tbs5520se: start downloading TBS5520se firmware
[  213.086614] usb 3-1: USB disconnect, device number 2
[  213.192459] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[  213.192799] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  213.192819] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[  213.192822] tbs5520se: read eeprom failed.
[  213.192828] dvb-usb: MAC address reading failed.
[  213.240158] i2c i2c-5: Added multiplexed i2c bus 6
[  213.240163] si2183 5-0067: Silicon Labs Si2183 successfully attached
[  213.760978] si2157: probe of 6-0061 failed with error -110
[  213.761181] dvb-usb: no frontend was attached by 'TurboSight TBS 5520SE'
[  213.761187] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.
[  213.761241] usbcore: registered new interface driver tbs5520se
[  213.761773] dvb-usb: TurboSight TBS 5520SE successfully deinitialized and disconnected.
[  214.934587] usb 3-1: new high-speed USB device number 3 using xhci_hcd
[  215.085357] usb 3-1: New USB device found, idVendor=734c, idProduct=5521
[  215.085363] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  215.085367] usb 3-1: Product: TBS 5521
[  215.085371] usb 3-1: Manufacturer: TBS-Tech
[  215.086243] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[  215.086247] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[  215.086249] tbs5520se: start downloading TBS5520se firmware
[  215.242903] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[  215.243233] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  215.243482] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[  215.474952] dvb-usb: MAC address: 00:22:ab:c0:45:33
[  215.479168] i2c i2c-5: Added multiplexed i2c bus 6
[  215.479173] si2183 5-0067: Silicon Labs Si2183 successfully attached
[  215.486080] si2157 6-0061: Silicon Labs Si2147/2148/2157/2158 successfully attached
[  215.514973] i2c i2c-6: av201x: Airoha Technology AV201x successfully attached
[  215.564015] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)...
[  215.564233] usb 3-1: DVB: registering adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)...
[  215.564825] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.
[  574.962669] /usr/src/enigma2pc-6.2/enigma2/dvbsoftwareca/dvb_softwareca.c: frontend loopback driver v0.0.1
[  574.962671] dvbsoftwareca: registering adapters
[  574.962876] dvbsoftwareca: register adapter0/ca0 @ minor: 0000
[  574.962878] dvbsoftwareca: registered CA0 device for adapter0
[  574.962999] dvbsoftwareca: register adapter0/ca1 @ minor: 0001
[  574.963001] dvbsoftwareca: registered CA1 device for adapter0
[  574.963240] dvbsoftwareca: registered 2 CA devices
[  711.682561] perf: interrupt took too long (2505 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1328.601473] perf: interrupt took too long (3203 > 3131), lowering kernel.perf_event_max_sample_rate to 62250
[ 2072.377738] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 2072.412273] JFS: nTxBlock = 8192, nTxLock = 65536
[ 2072.469800] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 2072.526500] QNX4 filesystem 0.2.3 registered.
[ 2072.595895] raid6: sse2x1   gen()  2360 MB/s
[ 2072.643836] raid6: sse2x1   xor()  1661 MB/s
[ 2072.691837] raid6: sse2x2   gen()  2526 MB/s
[ 2072.739920] raid6: sse2x2   xor()  1937 MB/s
[ 2072.788005] raid6: sse2x4   gen()  4560 MB/s
[ 2072.835833] raid6: sse2x4   xor()  2118 MB/s
[ 2072.835837] raid6: using algorithm sse2x4 gen() 4560 MB/s
[ 2072.835839] raid6: .... xor() 2118 MB/s, rmw enabled
[ 2072.835841] raid6: using ssse3x2 recovery algorithm
[ 2072.854298] xor: measuring software checksum speed
[ 2072.891970]    prefetch64-sse:  5879.000 MB/sec
[ 2072.931942]    generic_sse:  3211.000 MB/sec
[ 2072.931946] xor: using function: prefetch64-sse (5879.000 MB/sec)
[ 2073.007597] Btrfs loaded, crc32c=crc32c-intel
[ 3813.468564] perf: interrupt took too long (4004 > 4003), lowering kernel.perf_event_max_sample_rate to 49750
[ 7419.605894] do_general_protection: 12 callbacks suppressed
[ 7419.605896] traps: nemo[2094] general protection ip:494654 sp:7ffc92865838 error:0 in nemo[400000+1c2000]
root@mamad-VPCF133FX:/usr/local/e2/bin# dmesg | grep frontend
[  213.761181] dvb-usb: no frontend was attached by 'TurboSight TBS 5520SE'
[  215.564015] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)...
[  215.564233] usb 3-1: DVB: registering adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)...
[  574.962669] /usr/src/enigma2pc-6.2/enigma2/dvbsoftwareca/dvb_softwareca.c: frontend loopback driver v0.0.1

 

[momi133]

 

Attention. Don't update pulseaudio to version 12.2 in Ubuntu-18.04!
For me pulseaudio-desktop doesn't start by autostart. If you start manually, there is no sound in the Enigma2.

 

I installed Ubuntu 16.04 and e2pc is successfully installed!

 

but e2pc detect just  adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)

 

and doesn't show adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)! actually satellite tuner ( DVB-S/S2/S2X) is not detected!

 

I just need the satellite tuner( DVB-S/S2/S2X) and DVB-T/T2/C/C2/ISDB-T is not important!

 

please help me!

 

Please see this commands:

 

 

 

# ls -l  /dev/dvb/*
total 0
crw-------  1 root root  236, 0 Aug  9 07:38 ca0
crw-------  1 root root  236, 1 Aug  9 07:38 ca1
crw-rw----+ 1 root video 212, 0 Aug  9 07:32 demux0
lrwxrwxrwx  1 root root      24 Aug  9 07:38 demux1 -> /dev/dvb/adapter0/demux0
crw-rw----+ 1 root video 212, 1 Aug  9 07:32 dvr0
lrwxrwxrwx  1 root root      22 Aug  9 07:38 dvr1 -> /dev/dvb/adapter0/dvr0
crw-rw----+ 1 root video 212, 3 Aug  9 07:32 frontend0
crw-rw----+ 1 root video 212, 4 Aug  9 07:32 frontend1
crw-rw----+ 1 root video 212, 2 Aug  9 07:32 net0

 

 

 

# dmesg

[  213.021306] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[  213.036286] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[  213.036289] tbs5520se: start downloading TBS5520se firmware
[  213.086614] usb 3-1: USB disconnect, device number 2
[  213.192459] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[  213.192799] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  213.192819] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[  213.192822] tbs5520se: read eeprom failed.
[  213.192828] dvb-usb: MAC address reading failed.
[  213.240158] i2c i2c-5: Added multiplexed i2c bus 6
[  213.240163] si2183 5-0067: Silicon Labs Si2183 successfully attached
[  213.760978] si2157: probe of 6-0061 failed with error -110
[  213.761181] dvb-usb: no frontend was attached by 'TurboSight TBS 5520SE'
[  213.761187] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.
[  213.761241] usbcore: registered new interface driver tbs5520se
[  213.761773] dvb-usb: TurboSight TBS 5520SE successfully deinitialized and disconnected.
[  214.934587] usb 3-1: new high-speed USB device number 3 using xhci_hcd
[  215.085357] usb 3-1: New USB device found, idVendor=734c, idProduct=5521
[  215.085363] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  215.085367] usb 3-1: Product: TBS 5521
[  215.085371] usb 3-1: Manufacturer: TBS-Tech
[  215.086243] dvb-usb: found a 'TurboSight TBS 5520SE' in cold state, will try to load a firmware
[  215.086247] dvb-usb: downloading firmware from file 'dvb-usb-id5520se.fw'
[  215.086249] tbs5520se: start downloading TBS5520se firmware
[  215.242903] dvb-usb: found a 'TurboSight TBS 5520SE' in warm state.
[  215.243233] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  215.243482] dvbdev: DVB: registering new adapter (TurboSight TBS 5520SE)
[  215.474952] dvb-usb: MAC address: 00:22:ab:c0:45:33
[  215.479168] i2c i2c-5: Added multiplexed i2c bus 6
[  215.479173] si2183 5-0067: Silicon Labs Si2183 successfully attached
[  215.486080] si2157 6-0061: Silicon Labs Si2147/2148/2157/2158 successfully attached
[  215.514973] i2c i2c-6: av201x: Airoha Technology AV201x successfully attached
[  215.564015] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)...
[  215.564233] usb 3-1: DVB: registering adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)...
[  215.564825] dvb-usb: TurboSight TBS 5520SE successfully initialized and connected.
[  574.962669] /usr/src/enigma2pc-6.2/enigma2/dvbsoftwareca/dvb_softwareca.c: frontend loopback driver v0.0.1
[  574.962671] dvbsoftwareca: registering adapters
[  574.962876] dvbsoftwareca: register adapter0/ca0 @ minor: 0000
[  574.962878] dvbsoftwareca: registered CA0 device for adapter0
[  574.962999] dvbsoftwareca: register adapter0/ca1 @ minor: 0001
[  574.963001] dvbsoftwareca: registered CA1 device for adapter0
[  574.963240] dvbsoftwareca: registered 2 CA devices
[  711.682561] perf: interrupt took too long (2505 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1328.601473] perf: interrupt took too long (3203 > 3131), lowering kernel.perf_event_max_sample_rate to 62250
[ 2072.377738] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 2072.412273] JFS: nTxBlock = 8192, nTxLock = 65536
[ 2072.469800] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 2072.526500] QNX4 filesystem 0.2.3 registered.
[ 2072.595895] raid6: sse2x1   gen()  2360 MB/s
[ 2072.643836] raid6: sse2x1   xor()  1661 MB/s
[ 2072.691837] raid6: sse2x2   gen()  2526 MB/s
[ 2072.739920] raid6: sse2x2   xor()  1937 MB/s
[ 2072.788005] raid6: sse2x4   gen()  4560 MB/s
[ 2072.835833] raid6: sse2x4   xor()  2118 MB/s
[ 2072.835837] raid6: using algorithm sse2x4 gen() 4560 MB/s
[ 2072.835839] raid6: .... xor() 2118 MB/s, rmw enabled
[ 2072.835841] raid6: using ssse3x2 recovery algorithm
[ 2072.854298] xor: measuring software checksum speed
[ 2072.891970]    prefetch64-sse:  5879.000 MB/sec
[ 2072.931942]    generic_sse:  3211.000 MB/sec
[ 2072.931946] xor: using function: prefetch64-sse (5879.000 MB/sec)
[ 2073.007597] Btrfs loaded, crc32c=crc32c-intel
[ 3813.468564] perf: interrupt took too long (4004 > 4003), lowering kernel.perf_event_max_sample_rate to 49750
[ 7419.605894] do_general_protection: 12 callbacks suppressed
[ 7419.605896] traps: nemo[2094] general protection ip:494654 sp:7ffc92865838 error:0 in nemo[400000+1c2000]
root@mamad-VPCF133FX:/usr/local/e2/bin# dmesg | grep frontend
[  213.761181] dvb-usb: no frontend was attached by 'TurboSight TBS 5520SE'
[  215.564015] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SE DVB-T/T2/C/C2/ISDB-T)...
[  215.564233] usb 3-1: DVB: registering adapter 0 frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X)...
[  574.962669] /usr/src/enigma2pc-6.2/enigma2/dvbsoftwareca/dvb_softwareca.c: frontend loopback driver v0.0.1

 

 

 

[1455]

Why are you reinstalling Ubuntu again and again? You don't understand what you are doing.
The script is written so that it does almost everything itself! You can't break a sequence because the script is an algorithm expressed in a file.
I think about making a hdd image, but then it will not be free. Why? Because newbees don't want to study for free.

 

https://github.com/tbsdtv

[momi133]

Why are you reinstalling Ubuntu again and again? You don't understand what you are doing.

 

 

I reinstalling Ubuntu again and again because of following reasons:

 

1- e2pc didn't install in Ubuntu 14.04 because of confliction beetween gcc4.8 and gcc6 or g++4.8 and g++-6 and your script can't export g++-6 successfully and you can't solve this error in your scripts and finally you proposed me to install Ubuntu 18.04!

 

2- e2pc installed in Ubuntu 18.04  successfully but didn't run and frequently was up and down! and you can't solve this error or maybe you haven't enough ability!!!!???

 

3- finally I installed e2pc in Ubuntu 18.04  successfully without any error and without your help and tips!

 

we conclude that I understand what I am  doing but you don't understand what wrote in scripts!!! and it's understandable because Raider05, Cougar, nobody9 and betacentauri created this projects and ported  Enigma2 to Enigma2PC.

 

The script is written so that it does almost everything itself! You can't break a sequence because the script is an algorithm expressed in a file.

 

 

I didn't break any sequence and i run all scripts Respectively and continuously and after any run, I read logs!

 

https://github.com/tbsdtv

 

 

why do you send this? for editing? my card is multi-standard external TV tuner and I said that tbs card driver installed successfully and dmesg command confirm this but e2pc doesn't detect frontend 1 (TurboSight TBS 5520SE DVB-S/S2/S2X).

 

I'm sorry, I can speaking and writing English but can't speaking and writing in Russian language!!!!

[momi133]

tvheadend  detects both frontends and shows that tbs card driver is successfully installed! it is concluded that e2pc can't detect both frontends together and just detects frontend0!

 

it's a big bug!

 

 

 

 

[momi133]

Why are you reinstalling Ubuntu again and again? You don't understand what you are doing.
The script is written so that it does almost everything itself! You can't break a sequence because the script is an algorithm expressed in a file.
I think about making a hdd image, but then it will not be free. Why? Because newbees don't want to study for free.

 

https://github.com/tbsdtv

 

I'm sorry for previous post and I'm ashamed. Thanks a lot for all your tips and guides!

 

thanks a lot for your new tips in 4_build_openpliPC.sh but I saw this tips in Raider05 github page before! and the problem was not solved by setting NIM Sockets!

 

I send a massage to tbs supporter and he give me a driver so that just DVB-S2 tuner is recognized  by Enigma2pc!

 

# dmesg | grep frontend
[  149.605765] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SEDVB-S/S2/S2X)...
[  151.771342] usb 3-1: DVB: registering adapter 0 frontend 0 (TurboSight TBS 5520SEDVB-S/S2/S2X)...
[  152.452086] usb 3-1: DVB: adapter 0 frontend 0 frequency 0 out of range (950000..2150000)

 

# ls -l  /dev/dvb/*
total 0
crw-rw----+ 1 root video 212, 0  15 18:24 demux0
crw-rw----+ 1 root video 212, 1  15 18:24 dvr0
crw-rw----+ 1 root video 212, 3  15 18:24 frontend0
crw-rw----+ 1 root video 212, 2  15 18:24 net0

 

==> in tuner configuration, for dvb-T tuners, the word "Enabled" is appeared but for dvb-s2 in not appeared! why?

 

How to install skins and plugins ?

 

following method is wrote  in Raider05 github pages :

Adding systemplugins, extensions or skins

put systemplugins in /usr/local/e2/lib/enigma2/python/Plugins/SystemPlugins
put extensions in /usr/local/e2/lib/enigma2/python/Plugins/Extensions
put skin in /usr/local/e2/share/enigma2

 

How to install  .ipk files?

[1455]

If it is a special driver for DVB-S2 only, then e2pc nim_sockets should be look like this:

NIM Socket 0:
      Type: DVB-S2
      Name: TurboSight TBS 5520SEDVB-T/T2/C/C2/ISDB-T
      Has_Outputs: no
      Frontend_Device: 0

In the previous post it was obvious that you have DVB-S2 as frontend1. Then when using a standard driver it would look like this:

NIM Socket 0:
      Type: DVB-S2
      Name: TurboSight TBS 5520SEDVB-T/T2/C/C2/ISDB-T
      Has_Outputs: no
      Frontend_Device: 0

NIM Socket 1:
      Type: DVB-S2
      Name: TurboSight TBS 5520SEDVB-S/S2/S2X
      Has_Outputs: no
      Frontend_Device: 1

In this case, when setting up DVB-S2 converter, select the second item.

In the latest version of the script I made automatic creation nim_sockets for one or multi frontends dvb card and modified create_nim_sockets.c.
Also in the file README.EN described the case of multi frontend dvb cards. I have a multi card HVR-4000 and it works on a standard driver as the only one card in the system. The method described in  README.EN makes it possible to resolve the problem of plugins access to frontend1 when frontend0 is DVB-S2. But if frontend0 is DVB-T2 then don't do anything at all.

 

.ipk files are  specific for receivers only, and most will not work after unpacking on PC. Here, the version of enigma2 is considered to create new plug-ins on a computer and other tests, since compilation takes place an order of magnitude faster. Viewing channels here is not a competitor to programs such as VDR, for example. Therefore, there are still a lot of shortcomings and the problems.

Edited by 1455, 16 August 2018 - 10:25.

[1455]

How to install skins and plugins ?

 

This and similar questions are better to ask in other sections of the forum.

And in general, unpacking and looking content. There you can see where the archive files are placed.

ar -x *.ipk

[1455]

Another tip is not to forget that every time after installing a new kernel, need to rebuild, install and activate (depmod -a) of the dvbsoftwareca.ko module.

[1455]

<- rebuild, install and activate dvbsoftwareca.ko only by script because two kernel headers will be rewritten.

Edited by 1455, 16 August 2018 - 11:23.

[1455]

<-  Edited:

NIM Socket 0:
      Type: DVB-S2
      Name: TurboSight TBS 5520SEDVB-S/S2/S2X
      Has_Outputs: no
      Frontend_Device: 0

and

NIM Socket 0:
      Type: DVB-T2
      Name: TurboSight TBS 5520SEDVB-T/T2/C/C2/ISDB-T
      Has_Outputs: no
      Frontend_Device: 0

NIM Socket 1:
      Type: DVB-S2
      Name: TurboSight TBS 5520SEDVB-S/S2/S2X
      Has_Outputs: no
      Frontend_Device: 1

[pablocool]

Hi all

 

Is this script expected to work on Ubuntu 16.04?

In file included from osd.c:30:0:
osd.c: In function ‘gzread_i16’:
osd.c:855:9: error: request for member ‘have’ in something not a structure or union
   ret = gzgetc(fp);
         ^
osd.c:855:9: error: request for member ‘have’ in something not a structure or union
   ret = gzgetc(fp);
         ^
osd.c:855:9: error: request for member ‘pos’ in something not a structure or union
   ret = gzgetc(fp);
         ^
osd.c:855:9: error: request for member ‘next’ in something not a structure or union
   ret = gzgetc(fp);
         ^
osd.c:855:16: warning: passing argument 1 of ‘gzgetc’ from incompatible pointer type [-Wincompatible-pointer-types]
   ret = gzgetc(fp);
                ^
/usr/local/include/zlib.h:1510:21: note: expected ‘gzFile {aka struct gzFile_s *}’ but argument is of type ‘struct gzFile_s **’
 ZEXTERN int ZEXPORT gzgetc OF((gzFile file));
                     ^
osd.c:856:11: error: request for member ‘have’ in something not a structure or union
   ret |= (gzgetc(fp)<<8);
           ^
osd.c:856:11: error: request for member ‘have’ in something not a structure or union
   ret |= (gzgetc(fp)<<8);
           ^
osd.c:856:11: error: request for member ‘pos’ in something not a structure or union
   ret |= (gzgetc(fp)<<8);
           ^
osd.c:856:11: error: request for member ‘next’ in something not a structure or union
   ret |= (gzgetc(fp)<<8);

I have compilation errors probably due to wrong gcc version.

 

I base on this git repo

https://github.com/nobody9/openpliPC

Edited by pablocool, 24 August 2018 - 09:47.

[pablocool]

OK I discovered enigma2pc-6.2

 

But I fail on ./3_build_libxine.sh

libtool: install: (cd /home/ubuntu/enigma2pc-6.2/xine-lib-1.2-1.2.9+hg-e2pc/src/input; /bin/sh "/home/ubuntu/enigma2pc-6.2/xine-lib-1.2-1.2.9+hg-e2pc/libtool"  --silent --tag CC --mode=relink x86_64-linux-gnu-gcc -O3 -fexpensive-optimizations -ffast-math -fvisibility=hidden -pipe -Wall -Wformat=2 -Wno-format-zero-length -Wmissing-format-attribute -Werror-implicit-function-declaration -Wstrict-aliasing=2 -Wchar-subscripts -Wmissing-declarations -Wmissing-prototypes -Wwrite-strings -Wpointer-arith -g -Wall -Wchar-subscripts -Wnested-externs -Wcast-align -Wmissing-declarations -Wmissing-prototypes -Wmissing-format-attribute -Wno-pointer-sign -Wformat=2 -Wno-format-zero-length -Wformat-security -Wstrict-aliasing=2 -Werror=implicit-function-declaration -Wl,-z,defs -Wl,--gc-sections -avoid-version -module -Wl,-Bsymbolic -g -o xineplug_inp_bluray.la -rpath /usr/lib/xine/plugins/2.7 xineplug_inp_bluray_la-input_bluray.lo ../../src/xine-engine/libxine.la -lbluray -pthread media_helper.la input_helper.la -inst-prefix-dir /home/ubuntu/enigma2pc-6.2/xine-lib-1.2-1.2.9+hg-e2pc/debian/tmp)
.libs/xineplug_inp_bluray_la-input_bluray.o: In function `bluray_plugin_open':
/home/ubuntu/enigma2pc-6.2/xine-lib-1.2-1.2.9+hg-e2pc/src/input/input_bluray.c:1718: undefined reference to `bd_register_argb_overlay_proc'
.libs/xineplug_inp_bluray_la-input_bluray.o: In function `bluray_plugin_dispose':
/home/ubuntu/enigma2pc-6.2/xine-lib-1.2-1.2.9+hg-e2pc/src/input/input_bluray.c:1419: undefined reference to `bd_register_argb_overlay_proc'
collect2: error: ld returned 1 exit status
libtool:   error: error: relink 'xineplug_inp_bluray.la' with the above command before installing it

[1455]

You need to check manually and delete all files belonging to libxine2.