new it913x drivers not working in new kernel with et9000
Re: new it913x drivers not working in new kernel with et9000 #81
Re: new it913x drivers not working in new kernel with et9000 #82
Re: new it913x drivers not working in new kernel with et9000 #83
Posted 15 April 2013 - 17:51
Vu Solo2... USB DVB - Evolve Mars ( 048d:9006) , installed kernel module for it913x, firmware for it913x, but nothing added there in tuners.
Only on start E2 I can see:
Input device "ITE Technologies, Inc. USB Deivce" is a keyboard
Make sure you have installed also the kernel module kernel-module-it913x-fe in addition to the obvious kernel-module-dvb-usb-it913x.
Re: new it913x drivers not working in new kernel with et9000 #84
Re: new it913x drivers not working in new kernel with et9000 #85
Posted 16 April 2013 - 09:20
Still no success. When is pluged DVB-USB Evolve Mars dongle into vu solo2 (without installed drivers), then is visible with "lsusb" as
Bus 01 Device 003: ID: 048d:9006
After reboot box there is missing. There could be problem...
Edited by ims, 16 April 2013 - 09:24.
Re: new it913x drivers not working in new kernel with et9000 #86
Re: new it913x drivers not working in new kernel with et9000 #87
Re: new it913x drivers not working in new kernel with et9000 #88
Posted 16 April 2013 - 10:31
I think, there is some problem ( when I am trying modprobe dvb-usb-it913x ).
it913x: Chip Version=02 Chip Type=9135 it913x: Firmware Version 52887808 it913x: Remote HID mode NOT SUPPORTED it913x: Dual mode=0 Tuner Type=0 it913x: Unknown tuner ID applying default 0x60 usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in warm state usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer DVB: registering new adapter (ITE 9135(9006) Generic) it913x-fe: ADF table value :00 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 01 usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' error while loading driver (-19) usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' successfully deinitialized and disconnected [LCD]: unknown cmd 0x1015 FE tune usbcore: deregistering interface driver dvb_usb_it913x
Re: new it913x drivers not working in new kernel with et9000 #89
Posted 16 April 2013 - 18:48
I think, there is some problem ( when I am trying modprobe dvb-usb-it913x ).
it913x: Chip Version=02 Chip Type=9135 it913x: Firmware Version 52887808 it913x: Remote HID mode NOT SUPPORTED it913x: Dual mode=0 Tuner Type=0 it913x: Unknown tuner ID applying default 0x60 usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in warm state usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer DVB: registering new adapter (ITE 9135(9006) Generic) it913x-fe: ADF table value :00 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 usb 1-1: dvb_usb_v2: 2nd usb_bulk_msg() failed=-145 it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 01 usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' error while loading driver (-19) usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' successfully deinitialized and disconnected [LCD]: unknown cmd 0x1015 FE tune usbcore: deregistering interface driver dvb_usb_it913x
You can try to change the firmware parameter with modprobe:
modprobe dvb-usb-it913x firmware=1
and eventually firmware=2, firmware=3.
Re: new it913x drivers not working in new kernel with et9000 #90
Posted 16 April 2013 - 19:21
I think, I tried all this ( for 9006 it should be 2.fw). I think, it was same. I must load it always manualy, because after reboot is not more usb-stick in lsusb list.
When try with "loaded" module, enigma is finishing in "no idle".
I think, better will be try it under ultimo (or xp1000) personaly and know, if is stick ok.
Edited by ims, 16 April 2013 - 19:22.
Re: new it913x drivers not working in new kernel with et9000 #91
Posted 18 April 2013 - 10:33
Still problem, that after reboot is not USB-stick detected. When I put it to box and reload modules :
root@vusolo2:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Bus 002 Device 001: ID 1d6b:0002 Bus 003 Device 001: ID 1d6b:0002 Bus 004 Device 001: ID 1d6b:0002 Bus 005 Device 001: ID 1d6b:0001 Bus 006 Device 001: ID 1d6b:0001 Bus 007 Device 001: ID 1d6b:0001 Bus 008 Device 001: ID 1d6b:0001 Bus 001 Device 003: ID 048d:9006 root@vusolo2:~# lsmod Module Size Used by it913x_fe 30661 1 ipv6 311826 12 dvb_usb_it913x 9196 0 dvb_usb_v2 13716 1 dvb_usb_it913x fpga_directc 57649 0 brcmfb 1238 2 dvb_bcm7356 11704403 34 fpga_directc,brcmfb
Now i have not problem in dmesg. But when I am run enigma2 and saw on debug, it finishing on:
---- opening lame channel db reading services (version 4) loaded 8751 services linking adapter1/frontend0 to vtuner0 scanning for frontends.. opening frontend 0 close frontend 0 opening frontend 1 close frontend 1 opening frontend 2 main thread is non-idle! display spinner! no spinner DC! main thread is non-idle! display spinner! no spinner DC! main thread is non-idle! display spinner! no spinner DC! main thread is non-idle! display spinner! no spinner DC! ... ... ...
Re: new it913x drivers not working in new kernel with et9000 #92
Posted 18 April 2013 - 16:33
I tried this USB stick on Vu ultimo (I found, that there is not drivers) and after reboot it is still visible with lsusb.
On XP1000, where are drivers for this stick it works well. Only on Solo2 is problem. With/without drivers it does not exist in USB after reboot box more.
Re: new it913x drivers not working in new kernel with et9000 #93
Re: new it913x drivers not working in new kernel with et9000 #94
Re: new it913x drivers not working in new kernel with et9000 #95
Re: new it913x drivers not working in new kernel with et9000 #96
Posted 31 December 2013 - 19:07
Looks like a USB issue:
ehci-brcm ehci-brcm.0: force halt; handshake b0480314 00004000 00000000 -> -145 ehci-brcm ehci-brcm.0: HC died; cleaning up usb 1-2: USB disconnect, device number 3 dvb-usb: error while stopping stream.
I recently updated the IT913x patch with a few changes from the official driver mantainer.
If you had no problem with the previous version of the driver, we can revert the latest changes and wait for a fix from the mantainer.
I have that kind of error on my Vu+Duo2. Have you solved it on et box? If so can that patch be ported back to kernel 3.3.8 for Vu+Duo?
I have a 9006 ver 1 chipset and it is affected by the "Issues with 9006 Chip version 1 devices resetting USB controller" but that issue info is outdated maybe.
Regards.
Re: new it913x drivers not working in new kernel with et9000 #97
Posted 31 December 2013 - 19:48
OE-A has already integrate the following patches for linux-vuplus-3.3.8
it913x-backports-from-kernel-3.4.patch
it913x-backports-from-kernel-3.5.patch
it913x-fix-bulk-read-write-retry-loop.patch
it913x-switch-off-PID-filter-by-default.patch
So you can build kernel module by adding those patches and see if it fixes problems.
file://it913x-backports-from-kernel-3.4.patch \ file://it913x-backports-from-kernel-3.5.patch \ file://it913x-switch-off-PID-filter-by-default.patch \ file://it913x-fix-bulk-read-write-retry-loop.patch \Then you can send those to OpenPLi also, so other users will benefit.
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
Re: new it913x drivers not working in new kernel with et9000 #98
Posted 1 January 2014 - 18:15
I can see those files in:
meta-openpli/recipies-linux/linux/linux-vuplus-3.3.8
and they are listed in:
meta-openpli/recipies-linux/linux/linux-vuplus-3.3.8.inc
and that include file is required by:
linux-vuplus-3.3.8.bb
so I think those patches are integrated with openpli. If not, please name the file to modify.
Regards.
Re: new it913x drivers not working in new kernel with et9000 #99
Posted 1 January 2014 - 18:54
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
Re: new it913x drivers not working in new kernel with et9000 #100
Posted 1 January 2014 - 21:57
Thank you athoik for your guidance.
I've found first candidate and I am going to check it now.
Few questions about applying patch to kernel:
1. I got the code with: bitbake -c devshell linux-vuduo2 but there is no git for this linux of course, so I initialized one for easy patch creation. But the commit path in the patch file will be out of sync. Does it matter for bitbake?
2. Will it be enough to increase PR_INC in the linux-vuplus-3.3.8.inc file each time I update the patch? (linux-vuplus-3.3.8.inc is where I am going to add patch file to SRC_URI).
Regards.
3 user(s) are reading this topic
0 members, 3 guests, 0 anonymous users