55 replies to this topic

[pieterg]

But I guess there is no need to differentiate between different models.
All that really matters is the chipset:

root@et9x00:~# cat /proc/stb/info/chipset
bcm7405

[radxnl]

indeed, very good point

[nietgiftig]

on the etxxxx models please use /proc/stb/info/boxtype for correct box type detection

When I try this in putty I get a Permission denied

et9x00 login: root
root@et9x00:~# /proc/stb/info/boxtype
-sh: /proc/stb/info/boxtype: Permission denied

I see I forgot the cat

Edited by nietgiftig, 23 July 2012 - 20:38.

[Speedy1985]

HI all,

If have started with Carsten Presser, from karatelight.de.
We make a new grabber.

Faster, Better, and low cpu load. and it's open source .
This version wil come soon.

Kind regards Speedy1985

[pinkopallino69]

Hello Speedy

nothing changed

my setup:

- arduino uno with ledstream from adafruit
- led strip with 64 rgb leds driven by ws2801 ic
- your plugin beta2 ( i can install without issue)
- dm800 with last openpli 2.1


the setup is............................................

Hi,

Try this.
[device]
name ambilight
type momo
output /dev/ttyACM0 # or change this to /dev/ttyUSB0
channels 192 #Each led is 3 channels.
prefix 41 64 61 00 31 64 #prefix for 50 leds
#prefix 41 64 61 00 18 4D #prefix for 25 leds
interval 10000
rate 115200
debug off #turn this on to see what it's doing with the serial port
delayafteropen 1000000

Kind regards Speedy

i have tried but i have the same results:


Boblight-grab client 2.0b for DM500HD, DM800, DM8000, ET9000, VU+DUO.
© 2012 by Speedyisfast and Oktay Oeztueter)

Connecting to boblightd
Connected with boblightdeamon.

- Detected STB: Brcm7401



daemon:
d
root@dm800:/usr/sbin# boblightd -f
root@dm800:/usr/sbin# (InitLog) start of log /home/root/.boblight/boblightd.log
(PrintFlags) starting boblightd -f
(CConfig::LoadConfigFromFile) opening /etc/boblight.conf
(CConfig::CheckConfig) checking config lines
(CConfig::CheckConfig) config lines valid
(CConfig::BuildConfig) building config
(CConfig::BuildConfig) built config successfully
(main) starting devices
(CClientsHandler::Process) opening listening socket on *:19333
(CDevice::Process) ambilight: starting with output "/dev/ttyACM0"
(CDevice::Process) ambilight: setting up
(CClientsHandler::Process) 127.0.0.1:1246 connected
(CClientsHandler::ParseMessage) 127.0.0.1:1246 said hello
(CClientsHandler::ParseSet) 127.0.0.1:1246 priority set to 128

on the arduino only the tx led is blinking.

the log for lsmod:
root@dm800:/usr/sbin# lsmod
Module Size Used by
cdc_acm 13680 2
dvb_a867 201376 1
dvb_usb 18512 1 dvb_a867
8712u 358688 0
usbserial 32640 0
udf 100880 0
rt73 300112 0
rt3070sta 746256 0
8192cu 573904 0
ntfs 118048 0
nls_utf8 1600 0
nls_iso8859_15 4256 0
nls_cp850 4512 0
ext2 50960 0
exportfs 4832 0
lcd 13248 1
dreambox_keyboard 4208 0
dreambox_rc2 6432 1 dreambox_keyboard
bcm7401 3155536 31
cxd1981 15776 1 bcm7401
tu1216 42032 1 bcm7401
cu1216mk3 8512 1 bcm7401
bcm4506 94368 1 bcm7401
alps_bsbe2 44192 1 bcm7401
alps_bsbe1_c01a 19552 1 bcm7401
alps_bsbe1 6208 1 bcm7401
lnb_ctrl 6016 4 bcm4506,alps_bsbe2,alps_bsbe1_c01a,alps_bsbe1
stb_core 18912 10 lcd,dreambox_keyboard,dreambox_rc2,bcm7401,cxd1981,cu1216mk3,bcm4506,alps_bsbe2,alps_bsbe1_c01a,lnb_ctrl
stv0299 11824 1 alps_bsbe1
dvb_core 101616 5 dvb_usb,bcm7401,cxd1981,tu1216,stv0299
cifs 263648 0
cdfs 29728 0
nls_iso8859_1 3712 1
nls_cp437 5344 1

my box:

root@dm800:/proc/stb/info# cat /proc/stb/info/model
dm800

root@dm800:/proc/stb/info# cat /proc/cpuinfo
system type : BCM97xxx Settop Platform
build target : dm800
processor : 0
cpu model : Brcm3300 V0.0
cpu MHz : 294.91
BogoMIPS : 294.91 ( udelay_val : 147456 HZ = 1000 )
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : no
ASEs implemented : mips16
VCED exceptions : not available
VCEI exceptions : not available
RAC setting : I/D-RAC enabled
unaligned access : 879192
rdhwr/brdhwr traps : 0 / 0

[Speedy1985]

Hello Speedy

nothing changed

my setup:

- arduino uno with ledstream from adafruit
- led strip with 64 rgb leds driven by ws......

Hi, What is your prefix from boblight.conf ?

[pinkopallino69]

i used this:

### >> Adalight 64 lights << ###

[device]
name ambilight
output /dev/ttyACM0
channels 192
prefix 41 64 61 00 3f 6a
rate 115200
debug off
type momo
interval 10000
delayafteropen 1000000


i got info how calculate prefix from adafruit forum.
i also tried your prefix fro 50 led but the lights are always off (prefix 41 64 61 00 31 64 #prefix for 50 leds)
adalight works fine with selftest and atmowin.
i think something is wrong with daemon and grabber...maybe is dm800 that doesn't be compatible...
with which box do you test boblight?
i cant get arduino recognized on ttyUSB*, only ttyACM0 after loading kernel-module-cdc_acm
(dmesg>
cdc_acm 1-2.1:1.0: ttyACM0: USB ACM device
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters)

any hints?

[Speedy1985]

i used this:

### >> Adalight 64 lights << ###

[device]
name ambilight
output /dev/ttyACM0
channels 192
prefix 41 64 61 00 3f 6a
rate 115200
debug off
type momo
interval 10000
delayafteropen 1000000


i got info how calculate prefix from adafruit forum.
i also tried your prefix fro 50 led but the lights are always off (prefix 41 64 61 00 31 64 #prefix for 50 leds)
adalight works fine with selftest and atmowin.
i think something is wrong with daemon and grabber...maybe is dm800 that doesn't be compatible...
with which box do you test boblight?
i cant get arduino recognized on ttyUSB*, only ttyACM0 after loading kernel-module-cdc_acm
(dmesg>
cdc_acm 1-2.1:1.0: ttyACM0: USB ACM device
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters)

any hints?

What image you use ? And is the image oe1.6 or 2.0 ?
And do you have more usb devices connected ?

[pinkopallino69]

Openpli 2.1 (oe 1.6). I have attached a USB dvbt + Arduino forma adalight

[Speedy1985]

New release Boblight Enigma2 0.5r2

I,have started a new boblight project with Cartstenpresser from karatelight.de, and now we can bring or new version. [list]
[*] Better cpu load 5-10%
[*] buildin buffer
[*] better fps +/- 50fps
[*] better stb detection
[*]And some other bugs
[/list]
In few weeks we will bring a update...

For info, how to setup you controller in boblight.conf: go to http://code.google.c...ki/boblightconf

Kind regards CPresser and Martijn Vos(speedy1985)

Attached Files

•  enigma2-plugin-extensions-boblight-enigma2_0.5r2_mipsel.ipk   731.98KB   27 downloads

[pinkopallino69]

Good.
I Will try it soon ...hope i can Get it working with my dm800 this time.

Thanks

[pinkopallino69]

Hello

i'm still trying the new boblight pack (0.5r2) files with bad result.

i have installed last openpli 2.1 image with all update since now on my dm800hd.
installed cdc-acm module

i'm using arduino uno with ws2801 leds (adalight)

arduino recognized on /dev/ttyACM0
(dmesg> cdc_acm 1-2.1:1.0: ttyACM0: USB ACM device
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters)

using ledstrem.pde from adafruit/adalight git

64 led's strip ws2801

autotest on arduino works good...i have blue,green.red light on led at startup or when i launch boblightd:
root@dm800:/usr/sbin# boblightd -f
root@dm800:/usr/sbin# (InitLog) start of log /home/root/.boblight/boblightd.log
(PrintFlags) starting boblightd -f
(CConfig::LoadConfigFromFile) opening /etc/boblight.conf
(CConfig::CheckConfig) checking config lines
(CConfig::CheckConfig) config lines valid
(CConfig::BuildConfig) building config
(CConfig::BuildConfig) built config successfully
(main) starting devices
(CClientsHandler::Process) opening listening socket on *:19333
(CDevice::Process) ambilight: starting with output "/dev/ttyACM0"
(CDevice::Process) ambilight: setting up
(CClientsHandler::Process) 127.0.0.1:1246 connected
(CClientsHandler::ParseMessage) 127.0.0.1:1246 said hello
(CClientsHandler::ParseSet) 127.0.0.1:1246 priority set to 128

lights go in test mode (blue,green,red light), and then only tx light on arduino blinks

starting grabber:
root@dm800:/usr/bin# boblight-enigma2 -d
boblight-enigma2 © 2012 Martijn Vos and c@rstenpresser.de - see source for more information
Connecting to boblightd
(CClientsHandler::Process) 127.0.0.1:2115 connected
(CClientsHandler::ParseMessage) 127.0.0.1:2115 said hello
(CClientsHandler::ParseSet) 127.0.0.1:2115 priority set to 128
Connection to boblightd opened
[grabber] found STB-Type 1
[grabber] Maximum intermediate-picture-size is 128px
[grabber] Sync mode is on
[grabber] Setting Resolution to 88x72 (Source 704x576)
[grabber] Saving image to /tmp/boblight_enigma2_0000.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0001.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0002.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0003.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0004.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0005.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0006.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0007.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0008.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0009.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0010.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0011.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0012.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0013.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0014.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0015.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0016.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0017.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0018.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0019.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0020.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0021.bmp (88,72)
[grabber] Saving image to /tmp/boblight_enigma2_0022.bmp (88,72)

(it seems working), but lights always off. on arduino only tx led blinks

the log for lsmod:
root@dm800:/usr/sbin# lsmod
Module Size Used by
cdc_acm 13680 2
dvb_a867 201376 1
dvb_usb 18512 1 dvb_a867
8712u 358688 0
usbserial 32640 0
udf 100880 0
rt73 300112 0
rt3070sta 746256 0
8192cu 573904 0
ntfs 118048 0
nls_utf8 1600 0
nls_iso8859_15 4256 0
nls_cp850 4512 0
ext2 50960 0
exportfs 4832 0
lcd 13248 1
dreambox_keyboard 4208 0
dreambox_rc2 6432 1 dreambox_keyboard
bcm7401 3155536 31
cxd1981 15776 1 bcm7401
tu1216 42032 1 bcm7401
cu1216mk3 8512 1 bcm7401
bcm4506 94368 1 bcm7401
alps_bsbe2 44192 1 bcm7401
alps_bsbe1_c01a 19552 1 bcm7401
alps_bsbe1 6208 1 bcm7401
lnb_ctrl 6016 4 bcm4506,alps_bsbe2,alps_bsbe1_c01a,alps_bsbe1
stb_core 18912 10 lcd,dreambox_keyboard,dreambox_rc2,bcm7401,cxd1981,cu1216mk3,bcm4506,alps_bsbe2,alps_bsbe1_c01a,lnb_ctrl
stv0299 11824 1 alps_bsbe1
dvb_core 101616 5 dvb_usb,bcm7401,cxd1981,tu1216,stv0299
cifs 263648 0
cdfs 29728 0
nls_iso8859_1 3712 1
nls_cp437 5344 1

boblightconf:
### >> Adalight 64 lights << ###

[device]
name ambilight
output /dev/ttyACM0
channels 192
prefix 41 64 61 00 3f 6a
rate 115200
debug off
type momo
interval 10000
delayafteropen 1000000
and so on...

same result starting boblight-constant FFFF00 instead of grabber (leds always off).


programming arduino with atmolight compatible firmware and using mamba atmolight plugin i got leds working (but only a few leds, atmolight doesn't drive 64 leds).
in this case on arduino blinks tx and rx leds.

i thinks there are some troubles with daemon...but how can i debug more infos??

thanks

[Speedy1985]

Hi,

I think your device config is not good. Try this:

#For 50 leds 50x3 is 150 channels
[device]
name ambilight
type momo
output /dev/ttyACM0
channels 150
prefix 41 64 61 00 31 64
interval 10000
rate 115200
debug off #turn this on to see what it's doing with the serial port
delayafteropen 1000000

Use this pde
https://github.com/a...m/LEDstream.pde

And connect the wires like photo.

Kind regards Martijn

Attached Files

•  1zw1z4i.jpg   69.47KB   29 downloads

[pinkopallino69]

Hi,

I think your device config is not good. Try this:

#For 50 leds 50x3 is 150 channels
[device]
name ambilight
type momo
output /dev/ttyACM0
channels 150
prefix 41 64 61 00 31 64
interval 10000
rate 115200
debug off #turn this on to see what it's doing with the serial port
delayafteropen 1000000

Use this pde
https://github.com/a...m/LEDstream.pde

And connect the wires like photo.

Kind regards Martijn

hello

i have used either config for 25, 50 and 64 leds
i got infos how calculate prefix from adafruit developer...i'm sure prefix is good


i have used the same ledstream.pde


wires are conncted right )sefltest works ok)



any hints??

[Speedy1985]

Can you make a picture for me from the arduino ?
Send it via PM.

Have you tryed /dev/ttyUSB0 ??
And is atmolightd.ng closed ?? this can use the /dev/ttyUSB0

It must be work, i have the same, also arduino with 150 channels.

My device

[device]
name ambilight
type momo
output /dev/ttyUSB0
channels 150
prefix 41 64 61 00 31 64
interval 10000
rate 115200
debug off #turn this on to see what it's doing with the serial port
delayafteropen 1000000

[pinkopallino69]

Hello,

are you using dm800hd or othe dmm stb?
in my dm800 i can use only /dev/ttyACM0 i can't get /dev/ttyUSB0 ...either with mamba plugin i use /dev/ttyACM0 but i see data traffic...only with boblight it seems there is no traffic from daemon to arduino.

my arduino is like yours, only connected GND, data11, data13 (leds self test works ok).

maybe is something wrong with dm800hd? have you heard somebody with working boblight with dm800hd?

Later i will send you by pm some pics...

thanks