No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h
#1
Geplaatst op 21 september 2012 - 19:17
I was just wondering, that no one other had a problem with the daily Image from 14:29h?
I updated from 2012.09.20, and my et9200 couldn't tune anymore after the restart: No tuner available. Check your config.
Trying to do a new channel search ends immedienty with sero resuls. Also, the tuners can't find Astra & Eutelsat.
The only choice ist Inter...something & Thor.
Flashing the 2012.09.21 14:29h via a USB-Stick ends in exacly the same.
Flashing 2012.09.20 via a USB-Stick let my et9200 work normally again.
Autoupdating the 2012.09.20 to the daily image 2012.09.21 14:29h bricked the et9200 again.
Finally, I reflashed to yesterdays 2012.09.20 via a USB-Stick for having it working.
Best regards ;-)
Vu+ Uno 4K SE and Duo2 @ OpenPLi 6.2
formerly: Vu+ Duo1 -> xTrend et9200 -> VU+ Solo2
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #2
Geplaatst op 21 september 2012 - 19:32
so I went to tuner configuration menu and found out that my 19.2 /13.0 setup was replaced by 'automatic' entries on both ports...
I had to choose manually my sat positions and then everything started to work again
//probably side effect of this commit:
http://openpli.git.s...f23f0566c0f723f
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #3
Geplaatst op 21 september 2012 - 23:08
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #4
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #5
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #6
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #7
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #8
Geplaatst op 22 september 2012 - 02:12
A small note is that in the initial setup guide the 09-19 had "automatic" next to "advanced" in the tuner setup while that wasn't an option in the 09-21. Instead you could select "automatic" in the A or B section when you had selected "simple".
With 09-21 the initial guide didn't work, automatic scan didn't work, manual scan didn't work and satfinder didn't work. You crashed no matter how you set it up in the tuner config and you didn't even get to the next dialog (where you can clear before search and select which tuner you want to scan). I also tried to reset to factory defaults before reinstalling.
With 09-19 everything worked fine.
Re: No Astra 19,2 +Eutelsat 13,0 @ et9x00 @ OpenPLi3.0 2012.09.21 14:29h #9
Geplaatst op 22 september 2012 - 09:28
well, I also had problems with my tuner configuration after todays update - no signal,
so I went to tuner configuration menu and found out that my 19.2 /13.0 setup was replaced by 'automatic' entries on both ports...
I had to choose manually my sat positions and then everything started to work again
//probably side effect of this commit:
http://openpli.git.s...f23f0566c0f723f
indeed, because these settings were 'default' before, in your particular case the tuner config has not been stored to the settings file (default settings are not stored).
So when we changed the default to 'automatic', you lost your settings.
1 gebruiker(s) lezen dit onderwerp
0 leden, 1 bezoekers, 0 anonieme gebruikers