Hi!
Recently I've changed skin in one of my boxes, now I have dm800 with openpli2.1 in endless reboot loop (f*cked up skin).
This box has many files I need. Is there any way to change skin ? Maybe dump flash in flash upgrade mode and edit it?
Maybe it's possible to break startup sequence using remote? It's really important to me..., please help
Regards
Dumb
dm800 openpli2.1 endless reboot loop
Started by dumb, 01 Jan 2013 20:26
8 replies to this topic
Re: dm800 openpli2.1 endless reboot loop #2
-
- Forum Moderator
PLi® Core member - 33,471 posts
+118
Excellent
Posted 1 January 2013 - 20:31
connect by FTP and remove the skin directory
on the Glassfibre 1GB DVB-C...
Re: dm800 openpli2.1 endless reboot loop #3
-
- Senior Member
- 62 posts
0
Neutral
Posted 1 January 2013 - 20:44
it's impossible right now, box was connected to net via wifi
Re: dm800 openpli2.1 endless reboot loop #4
-
- Senior Member
- 62 posts
0
Neutral
Posted 1 January 2013 - 21:46
i've tried both wifi and lan connections, it looks like reboot loop is before network connectivity is started... any other suggestions please?
Re: dm800 openpli2.1 endless reboot loop #5
-
- PLi® Core member
- 14,045 posts
+298
Excellent
Posted 2 January 2013 - 14:06
Re-flash it, and don't install that skin again. That's by far the easiest method.
Real musicians never die - they just decompose
Re: dm800 openpli2.1 endless reboot loop #6
-
- Senior Member
- 1,596 posts
+49
Good
Posted 2 January 2013 - 21:11
I' not an expert, but I think it would be quite unusual for a skin to be causing a complete reboot. Usually it's just Enigma2 respawning continually. When trying to connect over the wired LAN, make sure that dhcp is running on the router, and hopefully DHCP was activated on the box. Scan your network or look into the router webif to see what address the DB picked up. If you didn't have dhcp activated or the ethernet port configured statically, sorry...
--
hemi
Ps. Putting the box into stop mode like you were going to flash should show you the IP the DB is pulling, if it is pulling...
PPs. If the files on the DB are desperately needed (besides learning to make backups), it might be worthwhile to learn how to boot the DB from either USB or the network. That would allow you to start up the DB, mount the flash and remove the problem skin and/or retrieve your files...
--
hemi
Ps. Putting the box into stop mode like you were going to flash should show you the IP the DB is pulling, if it is pulling...
PPs. If the files on the DB are desperately needed (besides learning to make backups), it might be worthwhile to learn how to boot the DB from either USB or the network. That would allow you to start up the DB, mount the flash and remove the problem skin and/or retrieve your files...
Edited by hemispherical1, 2 January 2013 - 22:21.
Re: dm800 openpli2.1 endless reboot loop #7
-
- Senior Member
- 1,449 posts
+69
Good
Posted 3 January 2013 - 01:56
Reboot before udhcpd means either flash filesystem corrupt or kernel/driver problem or hardware problem. Bad skin can't have those effects.
Re: dm800 openpli2.1 endless reboot loop #8
-
- Member
- 1 posts
0
Neutral
Posted 9 January 2013 - 01:31
What drives must be installed in the image of OpenPli to use the usb wifi adapter with RT5370 chipset in this picture .... Well tried downloading drives and still can not need a rescue.
And my dream is a clone ssl82 SIM2.01.
And my dream is a clone ssl82 SIM2.01.
Re: dm800 openpli2.1 endless reboot loop #9
-
- PLi® Core member
- 56,267 posts
+691
Excellent
Posted 9 January 2013 - 08:33
Now it seems to be a clone box.... so here stops our support....
As likely the newer DMM drivers do detect you're using a clone - causing what you do experience....
As likely the newer DMM drivers do detect you're using a clone - causing what you do experience....
Edited by littlesat, 9 January 2013 - 08:34.
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
