Posted 8 May 2013 - 12:32
Changelog:
-update to kernel 3.8.7
-improved EOF detection
-improved fastforward/rewind
-improved dts playback
-tuning speed optimizations
-HDMI CEC: use device type 'recorder' instead of 'tuner'
-increased default RC repeat rate
-et4000: fixed SCART RGB mode
-et4000: fixed simultaneous HDMI 1080p and SCART
-et6500: fixed VFD turn off
But we have to wait for update....
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 12:52
We are aware of that. But currently the buildserver is down due to a hardware failure, so you have to be patient and have us solve that first...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 8 May 2013 - 12:56
We are aware of that. But currently the buildserver is down due to a hardware failure, so you have to be patient and have us solve that first...
Can I find it somewhere and put it manually?
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 13:05
It needs a kernel update, so changes to the image source, the build scripts, etc. So if you want to do that, and then compile your own image, not a problem.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 8 May 2013 - 13:11
It needs a kernel update, so changes to the image source, the build scripts, etc. So if you want to do that, and then compile your own image, not a problem.
OK.I see,will wait for update...Thanks for info 
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 14:18
Hi,
Would be nice when you post such info to mention the hardware in the subject field:
Xtrend new kernel 3.8.7
would have been a better description. 
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 8 May 2013 - 14:23
At least for the ET9K currently an image is online....
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 8 May 2013 - 14:26
At least for the ET9K currently an image is online....
What about other boxes?Soon?
Edited by veskop, 8 May 2013 - 14:27.
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 14:30
See for yourself... also ready...
screenshot.jpg 95.52KB
299 downloads
Edited by littlesat, 8 May 2013 - 14:35.
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 8 May 2013 - 14:38
See for yourself... also ready...
Yes,upgrade ATM
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 15:09
Manual compile and placed on website or is the buildserver up and running again?
@Camping: ZGemma H.2S, Technisat Multytenne 4-in-1 @Home: Edision Mini 4K, Wave Frontier T55, EMP Centauri EMP DiSEqC 8/1 switch, 4x Inverto Ultra Black single LNB
Posted 8 May 2013 - 15:15
Manual compile and placed on website or is the buildserver up and running again?
buildserver is online I updated via receiver
Gigablue Quad +250GB HDD ~ Xtrend ET5000 ~ Triax110 Black Multifeed 36E/28E/23E ~ Total TV88 Multifeed 19E/16E/13E/9-7E ~ EMP Centauri 9/1 DiSEqC ~ Panasonic L42G20
Posted 8 May 2013 - 16:50
wow, i am surprised about the fact that channels with SR 30000 are working fine atm on tuner B with et9000 (eg. Planeta HD 23E or Mooz Dance HD on 0,8E)
But i have problems with PCTV 290e DVB-T2 USB/em28xx kernel modules (no prob. with 3.6.0):
DVB: registering new adapter (dvb0)
platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...
input: front panel as /devices/virtual/input/input2
NET: Registered protocol family 10
em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps (2013:024f, interface 0, class 0)
em28xx: DVB interface 0 found
em28xx #0: chip ID is em28174
Unhandled kernel unaligned access[#1]:
Cpu 1
$ 0 : 00000000 10008b00 00000000 0006a005
$ 4 : cde53000 00000000 00000004 cf795c30
$ 8 : 34000000 807b7941 00000000 20706968
$12 : 00000118 e0ffffff 00000000 00000000
$16 : cde53000 00000001 cde53000 8004be40
$20 : 00000004 00000000 e15e539c cf795c30
$24 : 00000008 e15e5360
$28 : cf794000 cf795bc8 cde534e0 e15e5388
Hi : 00000003
Lo : 26ed7c80
epc : e15e5158 em28xx_read_reg_req_len+0x48/0x250 [em28xx]
Tainted: GF O
ra : e15e5388 em28xx_read_reg_req+0x28/0x3c [em28xx]
Status: 10008b03 KERNEL EXL IE
Cause : 80800010
BadVA : 0006a005
PrId : 0002a044 (Brcm4380)
Modules linked in: em28xx(+) videobuf_vmalloc videobuf_core tveeprom ipv6 dvb(OF) modloader2(O) modloader(O) tpm(O)
Process modprobe (pid: 241, threadinfo=cf794000, task=cf113a18, tls=7780c490)
Stack : 00000006 ce016808 00000000 00000000 00000000 00000000 807b70b2 0000001d
00000000 ffffffff cff89800 cff89800 00000000 cde53000 8004be40 80724680
00000000 e15e539c 00000001 e15e5388 00000000 802e731c 00000000 00000000
00000001 cf795c44 cf795c44 cff89800 00000000 e15e481c ce00ee00 cde53000
00000000 805e6ec0 00002013 0000024f 00000000 00000000 cff82620 cff82600
...
Call Trace:
[<e15e5158>] em28xx_read_reg_req_len+0x48/0x250 [em28xx]
[<e15e5388>] em28xx_read_reg_req+0x28/0x3c [em28xx]
[<e15e481c>] em28xx_usb_probe+0x97c/0xcec [em28xx]
[<8040c3d8>] usb_probe_interface+0xf8/0x234
[<8034dbc0>] driver_probe_device+0xa0/0x2bc
[<8034de98>] __driver_attach+0xbc/0xc4
[<8034bf00>] bus_for_each_dev+0x5c/0xa8
[<8034d20c>] bus_add_driver+0x1b4/0x2b0
[<8034e234>] driver_register+0x90/0x1a0
[<8040b87c>] usb_register_driver+0x90/0x17c
[<80001588>] do_one_initcall+0x160/0x1e8
[<80073fcc>] load_module+0x1a1c/0x21b4
[<80074818>] sys_init_module+0xb4/0xec
[<8000e07c>] stack_done+0x20/0x40
Code: 8fb10060 30b500ff 30d4ffff <1440004f> 8c760000 2a220051 1040004e 3c12e15f 3c038000
---[ end trace a2e6780f574133d9 ]---
Posted 8 May 2013 - 17:05
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 8 May 2013 - 22:12
I have updated my ET4000 today, now I am experiencing a problem with HDMI CEC.
The attached Panasonic TV does not switch to the HDMI input any more when I switch on the ET4000.
Could this be related to the latest change: -HDMI CEC: use device type 'recorder' instead of 'tuner' ?
Posted 9 May 2013 - 10:25
wow, i am surprised about the fact that channels with SR 30000 are working fine atm on tuner B with et9000 (eg. Planeta HD 23E or Mooz Dance HD on 0,8E)
But i have problems with PCTV 290e DVB-T2 USB/em28xx kernel modules (no prob. with 3.6.0):
Same problem here. I will try to fix it ASAP.
em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps (2013:024f, interface 0, class 0)
em28xx: DVB interface 0 found
em28xx #0: chip ID is em28174
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == e15e5158, ra == e15e5388
Oops[#1]:
Cpu 0
$ 0 : 00000000 10008700 00000000 00000000
$ 4 : cf53c800 00000000 00000004 cde31c30
$ 8 : 34000000 807b7941 00000000 20706968
$12 : 0000010f e0ffffff 00000000 00000000
$16 : cf53c800 00000001 cf53c800 8004be40
$20 : 00000004 00000000 e15e539c cde31c30
$24 : 00000008 e15e5360
$28 : cde30000 cde31bc8 cf53cce0 e15e5388
Hi : 00000002
Lo : e9f3bec0
epc : e15e5158 em28xx_read_reg_req_len+0x48/0x250 [em28xx]
Tainted: GF O
ra : e15e5388 em28xx_read_reg_req+0x28/0x3c [em28xx]
Status: 10008703 KERNEL EXL IE
Cause : 80800008
BadVA : 00000000
PrId : 0002a044 (Brcm4380)
Modules linked in: em28xx(+) videobuf_vmalloc videobuf_core tveeprom ipv6 dvb(OF) modloader2(O) modloader(O) tpm(O)
Process modprobe (pid: 213, threadinfo=cde30000, task=cf750d28, tls=77ff4490)
Stack : 00000006 cde368c8 00000000 00000000 00000000 00000000 807b70b2 0000001d
00000000 ffffffff cfed3400 cfed3400 00000000 cf53c800 8004be40 80724680
00000000 e15e539c 00000001 e15e5388 00000000 802e731c 00000000 00000000
00000001 cde31c44 cde31c44 cfed3400 00000000 e15e481c cf459780 cf53c800
00000000 805e6ec0 00002013 0000024f 00000000 00000000 cfeb3020 cfeb3000
...
Call Trace:
[<e15e5158>] em28xx_read_reg_req_len+0x48/0x250 [em28xx]
[<e15e5388>] em28xx_read_reg_req+0x28/0x3c [em28xx]
[<e15e481c>] em28xx_usb_probe+0x97c/0xcec [em28xx]
[<8040c3d8>] usb_probe_interface+0xf8/0x234
[<8034dbc0>] driver_probe_device+0xa0/0x2bc
[<8034de98>] __driver_attach+0xbc/0xc4
[<8034bf00>] bus_for_each_dev+0x5c/0xa8
[<8034d20c>] bus_add_driver+0x1b4/0x2b0
[<8034e234>] driver_register+0x90/0x1a0
[<8040b87c>] usb_register_driver+0x90/0x17c
[<80001588>] do_one_initcall+0x160/0x1e8
[<80073fcc>] load_module+0x1a1c/0x21b4
[<80074818>] sys_init_module+0xb4/0xec
[<8000e07c>] stack_done+0x20/0x40
Code: 8fb10060 30b500ff 30d4ffff <1440004f> 8c760000 2a220051 1040004e 3c12e15f 3c038000
---[ end trace f073cec22dea399b ]---
Posted 9 May 2013 - 14:42
Hello!
Please don't get me wrong, but when do you expect a new OpenPli Image with integrated new kernel 3.8.7 will be relased for Xtrend Et-9200?
greeting
teleradio
Posted 9 May 2013 - 16:02
WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W
Posted 9 May 2013 - 16:06
wow, i am surprised about the fact that channels with SR 30000 are working fine atm on tuner B with et9000 (eg. Planeta HD 23E or Mooz Dance HD on 0,8E)
But i have problems with PCTV 290e DVB-T2 USB/em28xx kernel modules (no prob. with 3.6.0):
Same problem here. I will try to fix it ASAP.
I'm getting similar problems with many USB tuners.
This is an rtl2832 stick:
usb 1-2: new high-speed USB device number 3 using ehci-brcm
dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
do_cpu invoked from kernel context![#1]:
Cpu 1
$ 0 : 00000000 10008b00 00000000 00000001
$ 4 : 00000000 00000000 00000001 ffff00fe
$ 8 : cb2dffe0 00008b00 00000002 cdd79500
$12 : 000562eb 0000000e 00acf617 8061e738
$16 : 0000000e 00000020 00000000 cb14294c
$20 : 80460000 e18f647c e18f64fc e18f87c0
$24 : 000035f0 8000de40
$28 : cb2de000 cb2dfad8 00000000 8061e748
Hi : 00000011
Lo : 4836e080
epc : 8061e740 0x8061e740
Tainted: GF O
ra : 8061e748 0x8061e748
Status: 10008b03 KERNEL EXL IE
Cause : 9080002c
PrId : 0002a044 (Brcm4380)
Modules linked in: dvb_usb_rtl2832(+) dvb_usb nfsd exportfs ftdi_sio usbserial ipv6 dvb(OF) modloader2(O) modloader(O) tpm(O)
Process modprobe (pid: 478, threadinfo=cb2de000, task=cf1bd2b8, tls=774e8490)
Stack : c80a0000 cb142000 cb14294c cb14294c 80460000 e18f647c e18f64fc e18f87c0
00003550 8034e7e4 00808000 802e993c cb2de000 cb2dfb30 00000001 e19873ec
c80a0000 cb142000 cb14294c cb14294c 80460000 e1987414 cb142a10 80750000
806dd128 cb2dfb64 cb2dfb64 0000001d 00000000 8045bedc 806dd128 00000001
806dd1d8 00000000 806dd128 00000001 80687e38 00000000 8072bb20 e1b19298
...
Call Trace:
[<80460000>] dvb_dmx_swfilter_packet+0x24/0x5e0
[<e18f647c>] dvb_usb_fe_sleep+0x0/0x80 [dvb_usb]
[<e18f64fc>] dvb_usb_fe_wakeup+0x0/0x8c [dvb_usb]
[<8034e7e4>] klist_class_dev_get+0x0/0x8
[<802e993c>] __bzero+0x40/0x164
[<e19873ec>] rtl2832u_fe_attach+0x64/0xab4 [dvb_usb_rtl2832]
[<80460000>] dvb_dmx_swfilter_packet+0x24/0x5e0
[<e1987414>] rtl2832u_fe_attach+0x8c/0xab4 [dvb_usb_rtl2832]
[<8045bedc>] dvb_register_device+0x210/0x328
[<80460000>] dvb_dmx_swfilter_packet+0x24/0x5e0
[<e18f647c>] dvb_usb_fe_sleep+0x0/0x80 [dvb_usb]
[<e18f64fc>] dvb_usb_fe_wakeup+0x0/0x8c [dvb_usb]
[<e1982260>] rtl2832u_frontend_attach+0x20/0x38 [dvb_usb_rtl2832]
[<e18f6c08>] dvb_usb_adapter_frontend_init+0xe0/0x1cc [dvb_usb]
[<805e6ef8>] printk+0x38/0x44
[<805e6ec0>] printk+0x0/0x44
[<800c0000>] dma_pool_create+0xc0/0x1e4
[<e18f5bc8>] dvb_usb_device_init+0x554/0x75c [dvb_usb]
[<e18f5674>] dvb_usb_device_init+0x0/0x75c [dvb_usb]
[<e1982364>] rtl2832u_usb_probe+0x54/0x1a4 [dvb_usb_rtl2832]
[<8040c210>] usb_match_id+0x6c/0x98
[<8004f2b4>] blocking_notifier_call_chain+0x14/0x20
[<8040c3d8>] usb_probe_interface+0xf8/0x234
[<8034d8a0>] driver_sysfs_add+0x78/0xac
[<8034dbc0>] driver_probe_device+0xa0/0x2bc
[<8040c2a0>] usb_device_match+0x64/0xa4
[<8034de98>] __driver_attach+0xbc/0xc4
[<8034bbc4>] next_device+0x10/0x30
[<8034dddc>] __driver_attach+0x0/0xc4
[<8034bf00>] bus_for_each_dev+0x5c/0xa8
[<8034bb44>] bus_get+0x28/0x3c
[<8034d20c>] bus_add_driver+0x1b4/0x2b0
[<8034e178>] driver_find+0x18/0x44
[<8005731c>] default_wake_function+0x0/0x8
[<8034e234>] driver_register+0x90/0x1a0
[<8040b87c>] usb_register_driver+0x90/0x17c
[<e19de000>] rtl2832u_usb_module_init+0x0/0x64 [dvb_usb_rtl2832]
[<e19de030>] rtl2832u_usb_module_init+0x30/0x64 [dvb_usb_rtl2832]
[<8008d9f4>] free_hot_cold_page+0x30/0x220
[<800b8f48>] remove_vm_area+0x64/0xf0
[<80001588>] do_one_initcall+0x160/0x1e8
[<800b917c>] __vunmap+0xe4/0x128
[<8004f2b4>] blocking_notifier_call_chain+0x14/0x20
[<80073fcc>] load_module+0x1a1c/0x21b4
[<80070220>] ddebug_dyndbg_module_param_cb+0x0/0x3c
[<800711f8>] module_sect_show+0x0/0x18
[<80074818>] sys_init_module+0xb4/0xec
[<8000e07c>] stack_done+0x20/0x40
[<800c28a8>] sys_close+0x0/0x50
Code: 00000000 00000000 3b6e20c8 <76dc4190> 4db26158 edb88320 d6d6a3e8 9b64c2b0 a00ae278
---[ end trace 83fc56d5c0c2b902 ]---
I tested another em28xx tuner with the same results as the PCTV290e.
The A835 (af9035) driver loads fine, but Enigma2 hangs during boot.
The only stick working fine so far is the as102.
Is anyone else having similar problems? I just updated the image, maybe I should try to flash it....
Posted 9 May 2013 - 16:11
GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K
0 members, 15 guests, 0 anonymous users
