121 replies to this topic

[guirigui]

Please note, Gennar1, under Kernel 3.6.0, and earlier I had just to install the packet RTL2832u with 2 ipk only.

 

Both UT30 and UT40 were working flowless with the same driver

[Gennar1]

Please note, Gennar1, under Kernel 3.6.0, and earlier I had just to install the packet RTL2832u with 2 ipk only.

 

Both UT30 and UT40 were working flowless with the same driver

 

I know, but currently several USB tuner drivers don't work with the new kernel. It's a kernel bug, so we have to wait until a "magic patch" comes out.

 

Regarding your stick, can you run this commands:

 

modprobe dvb-usb-rtl28xxu
lsmod
dmesg

and post the results?

[guirigui]

result:
FATAL: Error inserting dvb-usb-rtl28xxu( (/lib/modules/3.8.7/kernel/drivers/media
/media/usb/dvb-usb-V2/dvb-usb-rtl28xxu.ko): Invalid argument

[Gennar1]

This errors usually happens when you mix kernel modules from different kernel versions.

Try:

opkg list-installed | grep kernel-module

and see if you can see mismatching kernel versions.

Then remove the bad modules with 'opkg remove kernel-module-whatever'.

 

Then you can check:

ls -l /lib/modules/

You should see only the 3.8.7 directory. If not, you can remove the other directories with 'rm -fr /lib/modules/3.6.0' or whatever you have but be careful!

Finally:

update-modules

should fix module dependencies.

Edited by Gennar1, 4 June 2013 - 17:42.

[guirigui]

I said, Gennar1, that I have installed the last image from sractch before testing the RTL38xxu packet..

I suppose there can't be different kernel version in the STB....unless there is a bug in the ET6x00 20130206  image... 

 I did so in order to get a clean image installation...

[Gennar1]

OK, then please post a dmesg AFTER the failed modprobe, to see the real error message from modprobe ("Invalid argument" is too generic to understand what's going on).

[guirigui]

In my today post, I did not updated the BOX....

So I did and, miracle...everything works flowless...

I could see many DVB-T modules updated

Congratulation to the Open PLi Team...indeed...

[Xtrend77]

oot@et9x00:~# [6n

lsmod

 

 

Module                  Size  Used by

dvb_usb_rtl28xxu       10812  0 

dvb_usb_v2             13604  1 dvb_usb_rtl28xxu

fc2580                  4662  1 dvb_usb_rtl28xxu

fc0012                  4692  1 dvb_usb_rtl28xxu

e4000                   4160  1 dvb_usb_rtl28xxu

rtl2832                 7786  1 dvb_usb_rtl28xxu

mt2060                  4022  1 dvb_usb_rtl28xxu

tua9001                 2502  1 dvb_usb_rtl28xxu

fc0013                  5879  1 dvb_usb_rtl28xxu

rtl2830                 6583  1 dvb_usb_rtl28xxu

r820t                  16661  1 dvb_usb_rtl28xxu

mxl5005s               31656  1 dvb_usb_rtl28xxu

qt1010                  4504  1 dvb_usb_rtl28xxu

ipv6                  338718  12 

dvb                  5292806  5 

modloader2             32590  1 dvb

modloader              22309  0 

tpm                     6745  3 dvb,modloader2,modloader

root@et9x00:~# [6n

[Xtrend77]

root@et9x00:~# [6n

dmesg

 

 

pci 0000:01:00.0: [14e4:8602] type 00 class 0x01010f

PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)

pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]

pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]

pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01

pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]

pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]

Bluetooth: Core ver 2.16

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO socket layer initialized

cfg80211: Calling CRDA to update world regulatory domain

Switching to clocksource upg

FS-Cache: Loaded

NET: Registered protocol family 2

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP: reno registered

UDP hash table entries: 256 (order: 1, 8192 bytes)

UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

PCI: CLS 0 bytes, default 64

NFS: Registering the id_resolver key type

Key type id_resolver registered

Key type i

d_legacy registered

fuse init (API version 7.20)

msgmni has been set to 567

io scheduler noop registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A

serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A

serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A

loop: module loaded

sata_brcmstb 0000:01:00.0: version 4.0

__clk_enable: sata [1]

PCI: Enabling device 0000:01:00.0 (0000 -> 0003)

sata_brcmstb 0000:01:00.0: setting latency timer to 64

scsi0 : sata_brcmstb

scsi1 : sata_brcmstb

ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42

ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42

Broadcom STB NAND controller (BrcmNand Controller)

bcmemac: Broadcom STB 10/100 EMAC driver v3.0

bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:6b:47)

bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)

usbcore: registered new interface driver zd1201

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

__clk_enable: usb [1]

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ehci-brcm ehci-brcm.1: Broadcom STB EHCI

ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2

ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500

ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3

ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

ohci-brcm ohci-brcm.1: Broadcom STB OHCI

ohci-brcm ohci-brcm.1: new USB bus regist

ered, assigned bus number 4

ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

usbcore: registered new interface driver btusb

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP: cubic registered

NET: Registered protocol family 17

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

Bluetooth: HIDP socket layer initialized

Key type dns_resolver registered

EBI CS1: setting up NAND flash (primary)

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecf10095

After: NandSelect=50000200, nandConfig=15142200

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff

timing1 not adjusted: 5363444f

timing2 not adjusted: 00000fc6

eccLevel=15, 1Ksector=0, oob=16

nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000

<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010

BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1

 

Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6

BrcmNAND version = 0x0302 128MB @00000000

B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecf10095

After: NandSelect=50000200, nandConfig=15142200

Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0

brcmnand_scan: B4 nand_select = 50000200

brcmnand_scan: After nand_select = 50000200

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000

ECC layout=brcmnand_oob_bch4_4k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsiz

e=512, writesize=2048

brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 not found for chip on CS1

Bad block table 1tbB not found for chip on CS1

Scanning device for bad blocks, options=00008000

ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

ata1.00: ATA-8: WDC WD10EADS-22M2B0, 01.00A01, max UDMA/133

ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)

ata1.00: configured for UDMA/133

scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EADS-22M 01.0 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sd 0:0:0:0: Attached scsi generic sg0 type 0

 sda: sda1

sd 0:0:0:0: [sda] Attached SCSI disk

Bad eraseblock 354 at 0x02c40000

ata2: SATA link down (SStatus 4 SControl 300)

Bad eraseblock 658 at 0x05240000

Bad eraseblock 951 at 0x076e0000

-->brcmnand_isbad_raw(offs=7fe0000

Bad block table written to 0x07fe0000, version 0x01

-->brcmnand_isbad_raw(offs=7fc0000

Bad block table written to 0x07fc0000, version 0x01

Adjust partition complete size from entire device to 7f00000 to avoid overlap with BBT reserved space

Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space

Creating 3 MTD partitions on "brcmnand.0":

0x000000000000-0x000007f00000 : "complete"

0x000000000000-0x000000600000 : "kernel"

0x000000600000-0x000007f00000 : "rootfs"

PM: CP0 COUNT/COMPARE frequency depends on divisor

UBI: attaching mtd2 to ubi0

usb 1-1: new high-speed USB device number 2 using ehci-brcm

usb 1-2: new high-speed USB device number 3 using ehci-brcm

usb 2-1: new high-speed USB device number 2 using ehci-brcm

hub 2-1:1.0: USB hub found

hub 2-1:1.0: 4 ports detected

UBI: scanning is finished

UBI: volume 0 ("rootfs") re-sized from 40

7 to 944 LEBs

UBI: attached mtd2 (name "rootfs", size 121 MiB) to ubi0

UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

UBI: good PEBs: 965, bad PEBs: 3, corrupted PEBs: 0

UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 220282331

UBI: available PEBs: 0, total reserved PEBs: 965, PEBs reserved for bad PEB handling: 17

UBI: background thread "ubi_bgt0d" started, PID 49

ALSA device list:

  No soundcards found.

Warning: unable to open an initial console.

UBIFS: background thread "ubifs_bgt0_0" started, PID 50

UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)

UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

UBIFS: FS size: 118468608 bytes (112 MiB, 933 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

UBIFS: reserved for root: 0 bytes (0 KiB)

UBIFS: media format: w4/r0 (latest is w4/r0), UUID C704414B-8CCC-475B-9891-6D6FBD08F216, small LPT model

VFS: Mounted root (ubifs filesystem) on device 0:10.

devtmpfs: mounted

Freeing unused kernel memory: 284k freed

usb 2-1.1: new high-speed USB device number 3 using ehci-brcm

scsi2 : usb-storage 2-1.1:1.0

usb 2-1.2: new full-speed USB device number 4 using ehci-brcm

scsi 2:0:0:0: Direct-Access     SanDisk  Cruzer           1.20 PQ: 0 ANSI: 5

sd 2:0:0:0: [sdb] 62530624 512-byte logical blocks: (32.0 GB/29.8 GiB)

sd 2:0:0:0: [sdb] Write Protect is off

sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00

sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA

sd 2:0:0:0: Attached scsi generic sg1 type 0

 sdb: sdb1

sd 2:0:0:0: [sdb] Attached SCSI removable disk

usb 2-1.1: USB disconnect, device number 3

EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended

EXT4-fs (sda1): recovery complete

EXT4-fs (sda1): mounted files

ystem with ordered data mode. Opts: (null)

usbcore: registered new interface driver tpm

dvb: module_layout: kernel tainted.

Disabling lock debugging due to kernel taint

Console: switching to colour frame buffer device 160x45

input: dreambox remote control (native) as /devices/virtual/input/input0

input: dreambox advanced remote control (native) as /devices/virtual/input/input1

DVB: registering new adapter (dvb0)

platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...

platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...

input: front panel as /devices/virtual/input/input2

NET: Registered protocol family 10

Console: switching to colour dummy device 80x25

Console: switching to colour frame buffer device 160x45

Console: switching to colour dummy device 80x25

usbcore: registered new interface driver dvb_usb_rtl28xxu

root@et9x00:~# [6n

[Xtrend77]

xtrend9000 not start up at that the drivers have been installed

[Xtrend77]

 

 

Module                  Size  Used by

em28xx                107028  1 

videobuf_vmalloc        4039  1 em28xx

videobuf_core          15665  2 em28xx,videobuf_vmalloc

tveeprom               11721  1 em28xx

ipv6                  338718  12 

dvb                  5292902  42 

modloader2             32590  1 dvb

modloader              22309  0 

tpm                     6745  3 dvb,modloader2,modloader

root@et9x00:~# [6n

dmesg

 

 

TCP: reno registered

UDP hash table entries: 256 (order: 1, 8192 bytes)

UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

PCI: CLS 0 bytes, default 64

NFS: Registering the id_resolver key type

Key type id_resolver registered

Key type id_legacy registered

fuse init (API version 7.20)

msgmni has been set to 567

io scheduler noop registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A

serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A

serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A

loop: module loaded

sata_brcmstb 0000:01:00.0: version 4.0

__clk_enable: sata [1]

PCI: Enabling device 0000:01:00.0 (0000 -> 0003)

sata_brcmstb 0000:01:00.0: setting latency timer to 64

scsi0 : sata_brcmstb

scsi1 : sata_brcmstb

ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42

ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42

Broadcom STB NAND controller (BrcmNand Controller)

bcmemac: Broadcom STB 10/100 EMAC driver v3.0

bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:6b:47)

bcmemac: not registering interface #1 at 0x1009

0000 (no PHY detected)

usbcore: registered new interface driver zd1201

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

__clk_enable: usb [1]

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ehci-brcm ehci-brcm.1: Broadcom STB EHCI

ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2

ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500

ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3

ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

ohci-brcm ohci-brcm.1: Broadcom STB OHCI

ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4

ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

usbcore: registered new interface driver btusb

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP: cubic registered

NET: Registered protocol family 17

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

Bluetooth: HIDP socket layer initialized

Key type dns_resolver registered

EBI CS1: setting up NAND flash (primary)

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecf10095

After: NandSelect=50000200, nandConfig=15142200

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128

 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff

timing1 not adjusted: 5363444f

timing2 not adjusted: 00000fc6

eccLevel=15, 1Ksector=0, oob=16

nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000

<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010

BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1

 

Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6

BrcmNAND version = 0x0302 128MB @00000000

B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1

brcmnand_read_id: CS1: dev_id=ecf10095

After: NandSelect=50000200, nandConfig=15142200

Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0

brcmnand_scan: B4 nand_select = 50000200

brcmnand_scan: After nand_select = 50000200

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000

ECC layout=brcmnand_oob_bch4_4k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsize=512, writesize=2048

brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS1

Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS1

nand_read_bbt: Bad block at 0x02c40000

nand_read_bbt: Bad block at 0x05240000

nand_read_bbt: Bad block at 0x076e0000

Adjust partition complete size from entire device to 7f00000 to avoid overlap with BBT reserved space

Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space

Creating 3 MTD partitions on "brcmnand.0":

0x000000000000-0x000007f00000 : "complete"

0x000000000000-0x000000600000 : "kernel"

0x000000600000-0x000007f00000 : "rootfs"

PM: CP0 COUNT/COMPARE frequency depends on divisor

UBI: attaching mtd2 to ubi0

usb 1-1: new high-speed USB device number 2 using ehci-brcm

usb 2-1: new high-speed 

USB device number 2 using ehci-brcm

hub 2-1:1.0: USB hub found

hub 2-1:1.0: 4 ports detected

usb 2-1.2: new full-speed USB device number 3 using ehci-brcm

UBI: scanning is finished

UBI: attached mtd2 (name "rootfs", size 121 MiB) to ubi0

UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

UBI: good PEBs: 965, bad PEBs: 3, corrupted PEBs: 0

UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1112285049

UBI: available PEBs: 0, total reserved PEBs: 965, PEBs reserved for bad PEB handling: 17

ALSA device list:

  No soundcards found.

Warning: unable to open an initial console.

UBI: background thread "ubi_bgt0d" started, PID 49

ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

ata1.00: ATA-8: WDC WD10EADS-22M2B0, 01.00A01, max UDMA/133

ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)

ata1.00: configured for UDMA/133

scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EADS-22M 01.0 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)

sd 0:0:0:0: Attached scsi generic sg0 type 0

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

 sda: sda1

sd 0:0:0:0: [sda] Attached SCSI disk

ata2: SATA link down (SStatus 4 SControl 300)

UBIFS: background thread "ubifs_bgt0_0" started, PID 51

UBIFS: recovery needed

UBIFS: recovery completed

UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)

UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

UBIFS: FS size: 118468608 bytes (112 MiB, 933 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

UBIFS: reserved for root: 0 bytes (0 KiB)

UBIFS: media format: w4/r0 (latest is w4/r0), UUID 9258FEF8-47C6-45DF-92AA-8B66C6208F85, small LPT

 model

VFS: Mounted root (ubifs filesystem) on device 0:10.

devtmpfs: mounted

Freeing unused kernel memory: 284k freed

EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended

EXT4-fs (sda1): recovery complete

EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)

usbcore: registered new interface driver tpm

dvb: module_layout: kernel tainted.

Disabling lock debugging due to kernel taint

Console: switching to colour frame buffer device 160x45

input: dreambox remote control (native) as /devices/virtual/input/input0

input: dreambox advanced remote control (native) as /devices/virtual/input/input1

DVB: registering new adapter (dvb0)

platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...

platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...

input: front panel as /devices/virtual/input/input2

NET: Registered protocol family 10

em28xx: New device TERRATEC TERRATCE H5 Rev.3 @ 480 Mbps (0ccd:10b6, interface 0, class 0)

em28xx: Audio Vendor Class interface 0 found

em28xx: Video interface 0 found

em28xx: DVB interface 0 found

em28xx #0: chip ID is em2884

CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == e15e5158, ra == e15e5388

Oops[#1]:

Cpu 0

$ 0   : 00000000 10008700 00000000 00000000

$ 4   : ce792800 00000000 00000004 cf7bfc30

$ 8   : 34383832 807b7940 00000000 20706968

$12   : 0000010c e0ffffff 00000000 00000000

$16   : ce792800 00000001 ce792800 8004be40

$20   : 00000004 00000000 e15e539c cf7bfc30

$24   : 00000000 e15e5360                  

$28   : cf7be000 cf7bfbc8 ce792ce0 e15e5388

Hi    : 00000003

Lo    : 7e3f9cc0

epc   : e15e5158 em28xx_read_reg_req_len+0x48/0x250 [em28xx]

    Tainted: GF          O

ra    : e15e5388 em28xx_read_reg_req+0x28/0x3c [em28xx]

Status: 10008703    KERNEL EXL IE 

Cause : 80800008

BadVA : 00000000

PrId  : 0002a044 (Brcm4380)

Modules linked in: em28xx(+) videobuf_vmalloc videobuf_core tveeprom ipv6 dvb(OF) modloader2(O) modloader(O) tpm(O)

Process m

odprobe (pid: 210, threadinfo=cf7be000, task=cf023278, tls=77118490)

Stack : 00000006 00000003 00000000 00000000 00000000 00000000 807b70b2 0000001c

        00000000 ffffffff cfed3000 cfed3000 00000000 ce792800 8004be40 80724680

        00000000 e15e539c 00000001 e15e5388 00000001 802e731c 00000000 00000000

        00000001 cf7bfc44 cf7bfc44 cfed3000 00000000 e15e481c cddbf700 ce792800

        00000000 805e6ec0 00000ccd 000010b6 00000000 00000000 cff50220 cff50200

        ...

Call Trace:

[<e15e5158>] em28xx_read_reg_req_len+0x48/0x250 [em28xx]

[<e15e5388>] em28xx_read_reg_req+0x28/0x3c [em28xx]

[<e15e481c>] em28xx_usb_probe+0x97c/0xcec [em28xx]

[<8040c3d8>] usb_probe_interface+0xf8/0x234

[<8034dbc0>] driver_probe_device+0xa0/0x2bc

[<8034de98>] __driver_attach+0xbc/0xc4

[<8034bf00>] bus_for_each_dev+0x5c/0xa8

[<8034d20c>] bus_add_driver+0x1b4/0x2b0

[<8034e234>] driver_register+0x90/0x1a0

[<8040b87c>] usb_register_driver+0x90/0x17c

[<80001588>] do_one_initcall+0x160/0x1e8

[<80073fcc>] load_module+0x1a1c/0x21b4

[<80074818>] sys_init_module+0xb4/0xec

[<8000e07c>] stack_done+0x20/0x40

 

 

Code: 8fb10060  30b500ff  30d4ffff <1440004f> 8c760000  2a220051  1040004e  3c12e15f  3c038000 

---[ end trace b57911fb232399d6 ]---

Console: switching to colour dummy device 80x25

root@et9x00:~# [6

[robertut]

 

 

 

Good morning,

 

also works with a usb dvb-t stick em28xx? If yes how do I upload the plugin for this stick?

 

Thanks a lot for your help.

 

No, sorry.

The em28xx driver is for USB devices produced by Empia.

The rtl28xxu driver is for USB devices produced by Realtek.

They are completely different beasts

 

Ok thanks lot Gennar1,

 

at this point, you think I can use it soon or is it better to buy another compatible?

 

Mauro

 

Use OpenPLi 2.1...

[wavelet]

Use OpenPLi 2.1...

 
You could also try building your own image with the 3.6.0 kernel by checking out from the git repository the commit just before the kernel was changed to 3.8.7.

mkdir openpli-3.0
cd openpli-3.0
git clone git://git.code.sf.net/p/openpli/openpli-oe-core
cd openpli-oe-core
git checkout 34158b82fec83859839421d642e32ef3a644a3da
make -f Makefile MACHINE=etxx00
make image

Ignore the warning messages about detached HEAD.

[pieterg]

It's a kernel bug, so we have to wait until a "magic patch" comes out.

Looks like I finally have the 'magic patch'.
I traced it down to http://git.kernel.or...3a9070827796cfc

So indeed, a MIPS-only issue.

Edited by pieterg, 28 July 2013 - 14:45.

[robertut]

Will it be included in OpenPLi?

[littlesat]

As far I can see it is already committed and a new build was started...

[robertut]

Use OpenPLi 2.1...

 
You could also try building your own image with the 3.6.0 kernel by checking out from the git repository the commit just before the kernel was changed to 3.8.7.

mkdir openpli-3.0
cd openpli-3.0
git clone git://git.code.sf.net/p/openpli/openpli-oe-core
cd openpli-oe-core
git checkout 34158b82fec83859839421d642e32ef3a644a3da
make -f Makefile MACHINE=etxx00
make image

Ignore the warning messages about detached HEAD.

 

 

 

Hi!

 

I'm trying to build my own image. Followed all the steps from the wiki, and your instructions above and I get this:

 

mi@dev-x64:~/dev/openpli-3.0/openpli-oe-core$ make image
Building image for et6x00
Traceback (most recent call last):
  File "/usr/bin/bitbake", line 234, in <module>
    ret = main()
  File "/usr/bin/bitbake", line 197, in main
    server = ProcessServer(server_channel, event_queue, configuration)
  File "/usr/lib/pymodules/python2.7/bb/server/process.py", line 78, in __init__
    self.cooker = BBCooker(configuration, self.register_idle_function)
  File "/usr/lib/pymodules/python2.7/bb/cooker.py", line 76, in __init__
    self.parseConfigurationFiles(self.configuration.file)
  File "/usr/lib/pymodules/python2.7/bb/cooker.py", line 510, in parseConfigurationFiles
    data = _parse(os.path.join("conf", "bitbake.conf"), data)
TypeError: getVar() takes exactly 3 arguments (2 given)
ERROR: Error evaluating '${TARGET_OS}:${TRANSLATED_TARGET_ARCH}:build-${BUILD_OS}:pn-${PN}:${MACHINEOVERRIDES}:${DISTROOVERRIDES}:forcevariable${LIBCOVERRIDE}'
Traceback (most recent call last):
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 116, in expandWithRefs
    s = __expand_var_regexp__.sub(varparse.var_sub, s)
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 60, in var_sub
    var = self.d.getVar(key, 1)
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 260, in getVar
    return self.expand(value, var)
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 132, in expand
    return self.expandWithRefs(s, varname).value
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 117, in expandWithRefs
    s = __expand_python_regexp__.sub(varparse.python_sub, s)
TypeError: getVar() takes exactly 3 arguments (2 given)

ERROR: Error evaluating '${@bb.parse.BBHandler.vars_from_file(d.getVar('FILE'),d)[0] or 'defaultpkgname'}'
Traceback (most recent call last):
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 117, in expandWithRefs
    s = __expand_python_regexp__.sub(varparse.python_sub, s)
  File "/usr/lib/pymodules/python2.7/bb/data_smart.py", line 76, in python_sub
    value = utils.better_eval(codeobj, DataContext(self.d))
  File "/usr/lib/pymodules/python2.7/bb/utils.py", line 387, in better_eval
    return eval(source, _context, locals)
  File "PN", line 1, in <module>
TypeError: getVar() takes exactly 3 arguments (2 given)

make: *** [image] Error 1
mi@dev-x64:~/dev/openpli-3.0/openpli-oe-core$

[robertut]

Nevermind, the problem was on my computer: the filesystem designed to store the files was mounted without the exec option.

[Gennar1]

It's a kernel bug, so we have to wait until a "magic patch" comes out.

Looks like I finally have the 'magic patch'.
I traced it down to http://git.kernel.or...3a9070827796cfc

So indeed, a MIPS-only issue.

 

Great news! Unfortunately I will not be able to test it for a while.

BTW, how do you tracked the issue down to that patch? I was planning to run a full git bisect between 3.6 and 3.8.7...

 

Anyway, great job as usual! TY!

[pieterg]

BTW, how do you tracked the issue down to that patch? I was planning to run a full git bisect between 3.6 and 3.8.7...

Indeed, I did a bisect, quite a painful one, having to rebase / cherry-pick the necessary broadcom support for each iteration, lots of merge conflicts that had to be resolved manually...
Took me a long time, glad it worked out in the end.
(not that I have seen many success stories yet, but I'm convinced this has to be the actual fix)