I cannot communicate with the box (192.168.0.17)
if I do "ping 192.168.0.17" in a MS Dos box, I get no answer.
The receiver does not show up as connected at the router UI (192.168.0.1)
Solo2 "loop out"
Started by Dimitrij, 30 Jun 2013 16:25
115 replies to this topic
Re: Solo2 "loop out" #102
-
- Senior Member
- 141 posts
0
Neutral
Posted 23 November 2016 - 15:33
Hi Dimitrij,
I am making a last attempt to install the plugin as I am happy with most of the parameters of the OpenPLI but I still conclude that the plugin does not work.
I made the following in DCC / Telnet:
opkg update
cd /tmp
[put plugin version 1.2 in /var/tmp]
opkg install enigma2....ipk
[got 2 lines about installation and configuration]
init 4
enigma2
I started recording of TF1 on Eutelsat 5WA
I can only select the programs from the same transponder, the other ones are grey.
What do you suggest?
Re: Solo2 "loop out" #104
-
- Senior Member
- 141 posts
0
Neutral
Posted 23 November 2016 - 23:17
No changes, unfortunately.
In DCC, I did opkg update and then ...
I tune to Das Erste (11493H on 19.2°east)
If I press "Channel +", it switched to Arte which is on the same frequency and not to ZDF which is on 11361H ands remains grey.
Re: Solo2 "loop out" #105
-
- PLi® Core member
- 10,328 posts
+350
Excellent
Posted 24 November 2016 - 09:13
Maybe need tuner B loop through to tuner A.
Cable connected is tuner A.
GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K
Re: Solo2 "loop out" #106
-
- Senior Member
- 141 posts
0
Neutral
Posted 24 November 2016 - 10:07
User manual says (page 15) : In case you only have one satellite cable, connect it to LNB2 input (I have this here)
Tuner B is the main tuner with disecq A/B/C/D. Tuner A is a loopthrough of B.
When connected to LNB2 and I set tuner A as main tuner and tuner B as loopthrough there is no signal.
http://vuplus.com/ma...ual_English.pdf
Re: Solo2 "loop out" #107
-
- PLi® Core member
- 10,328 posts
+350
Excellent
Posted 24 November 2016 - 11:05
GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K
Re: Solo2 "loop out" #108
-
- Senior Member
- 141 posts
0
Neutral
Posted 24 November 2016 - 11:28
After another reboot, it's now working fine without inverting tuner A and B. As a test I am recording France 3 (11555V) and watching TF1. It works great.
Thanks Dimitrij.
Re: Solo2 "loop out" #109
-
- PLi® Core member
- 10,328 posts
+350
Excellent
Posted 24 November 2016 - 11:48
Bingo 
GigaBlue UHD Quad 4K /Lunix3-4K/Duo 4K
Re: Solo2 "loop out" #110
-
- PLi® Contributor
- 6,181 posts
+261
Excellent
Posted 24 November 2016 - 17:54
Hi,
Just for my information, will this plugin be installed automatically in OpenPLi for all the the VU+ Solo2 or will end-users still need to install it manually (or better from the OpenPLi feed)?
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Solo2 "loop out" #111
-
- Forum Moderator
PLi® Core member - 14,925 posts
+486
Excellent
Posted 26 November 2016 - 14:32
I've added the plugin to the vusolo2 feed.
Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....
On the edge of the abyss, a step forward is not always progress....
Hardware: 2x Daily used Vu+ Ultimo 4K - Vu+ Duo 4K SE and a lot more.... - VisioSat BiBigsat - Jultec Unicable Multiswitch 4 positions: 19.2/23.5/28.2 East - Diseqc motorized flatdish antenna
Software : HomeBuild OpenPLi Develop and Scarthgap builds, local cards driven by OsCam
Press the 
button on the buttom right of this message 
Have you tried our wiki yet? Many answers can be found in our OpenPLi wiki
Re: Solo2 "loop out" #112
-
- PLi® Contributor
- 6,181 posts
+261
Excellent
Posted 26 November 2016 - 16:49
But it won't be installed by default in the image for the Solo2?
If not this will again raise questions about this issue on the forum. So I think that for the Solo2 this should be pre-installed in the image, just my 2 cents.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Solo2 "loop out" #113
-
- PLi® Core member
- 2,345 posts
+121
Excellent
Posted 26 November 2016 - 19:08
Why it should be pre-installed on solo2?
Maybe I miss something, but if I have a receiver with two tuners, why by default I should connected to sat only one of them?
I have connected both tuners and I have not seen some kind of problem to use them both without this hack on my solo2.
Edited by Taapat, 26 November 2016 - 19:08.
Re: Solo2 "loop out" #114
-
- Senior Member
- 7,766 posts
+184
Excellent
Posted 26 November 2016 - 19:12
Because it enables a normal option of the box.
Re: Solo2 "loop out" #115
-
- PLi® Contributor
- 6,181 posts
+261
Excellent
Posted 26 November 2016 - 23:40
Why it should be pre-installed on solo2?Maybe I miss something, but if I have a receiver with two tuners, why by default I should connected to sat only one of them?I have connected both tuners and I have not seen some kind of problem to use them both without this hack on my solo2.
Because for exemple French Canal(sat) arranges its channel to be in the same quadrant on Astra 19.2E, so with one single cable and internal loop through between the tuner, you can record and watch another channel but this is not working on Solo2.
So not everybody connect a cable per tuner, many people use loop through option and this one is not working in standard OpenPLi image.
So end-use will need to install this module specifically on VU+ Solo2 otherwise it simply doesn't work, the end-user is stuck on the same TP while normally it should be allowed to watch any channels in the same quadrant.
So yes, this sounds like another VU+ driver bug and should be fixed by VU+ but since an external plugin solved it, why not install it by default on Solo2. If you have 2 cables this won't change anything for you, but this will ease OpenPLi VU+ Solo2 end-users... or they will turn to another image where it is working by default.
Or do I miss that this plugin prevent 2 independant tuners from working, so yes in this case this should remains as an optional package.
I don't own a Solo2 myself so I cannot test it.
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: Solo2 "loop out" #116
-
- PLi® Core member
- 46,969 posts
+542
Excellent
Posted 27 November 2016 - 09:07
I am not in favour of installing it by default. It's better to only workaround defeciencies, not hide them.
* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.
9 user(s) are reading this topic
0 members, 9 guests, 0 anonymous users
