7 replies to this topic

[satmus]

kernel-module-dvb-usb-rtl2832 - 3.3.8-r0

 

dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
RTL2832U usb_init_bulk_setting : USB2.0 HIGH SPEED (480Mb/s)
RTL2832U check_tuner_type : ERROR Unknown tuner on board...
dvb-usb: no frontend was attached by 'RTL2832U DVB-T USB DEVICE'
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_rtl2832u

 

Volgens dit topic: http://openpli.org/f...b-rtl2832r820t/

 

The dvb_usb_rtl2832 driver on ET9000 has been updated recently, after I found a new version of the Realtek original driver with support for the r820t tuner.

The solution is to update the rtl2832 patch also for the VU+ kernels.

 

Zou iemand misschien ook de VU+ kernels kunnen updaten? Of is er meer aan de hand?

 

Bedankt,

 

satmus

[cyb]

Hello,

 

I've just done an "opkg install kernel-module-dvb-usb-rtl2832" command via Telnet and my two RTL2832 tuners are installed and seems to be ready to use on my VU+DUO2.

hey both appear on the Tuner List and I can setup them.

 

I do not know yet if there is any signal incomming as my antenna is not plugged yet. I will do better tests this afternoon and post the results.

 

cyb

[jbnl]

Can this stick also handle DVB_C ?

[satmus]

Can this stick also handle DVB_C ?

 

It can handle DVB-T and also DAB and FM, but I'm not sure it is all supported in Enigma2.

 

satmus

Edited by satmus, 30 August 2013 - 18:12.

[satmus]

Hello,

 

I've just done an "opkg install kernel-module-dvb-usb-rtl2832" command via Telnet and my two RTL2832 tuners are installed and seems to be ready to use on my VU+DUO2.

hey both appear on the Tuner List and I can setup them.

 

I do not know yet if there is any signal incomming as my antenna is not plugged yet. I will do better tests this afternoon and post the results.

 

cyb

 

 

Does your stick have the r820t tuner?

 

This is the one I bought:  http://www.ebay.com/...=item2579f144b7

 

satmus

[cyb]

Sorry, I did not see this was a thread about an hybrid stick...

 

Mine are just DVB-T and they are both working perfectly with the RTL2832U package. So I think the problem is related to the other abilities of this tuner... Hope this could help...

Edited by cyb, 30 August 2013 - 18:13.

[satmus]

Linux driver sources and datasheet from the R820T can be found in this thread:

 

https://groups.googl...LI[51-75-false]

 

Could someone educate me a bit who maintains the Vu+ kernel and howto get the new driver code included? Can the exact same driver sources be used from the ET9000?

 

thanks

 

satmus

[macnuts]

satmus, on 30 Aug 2013 - 19:11, said:

 

cyb, on 30 Aug 2013 - 13:51, said:

Hello,

 

I've just done an "opkg install kernel-module-dvb-usb-rtl2832" command via Telnet and my two RTL2832 tuners are installed and seems to be ready to use on my VU+DUO2.

hey both appear on the Tuner List and I can setup them.

 

I do not know yet if there is any signal incomming as my antenna is not plugged yet. I will do better tests this afternoon and post the results.

 

cyb

 

 

Does your stick have the r820t tuner?

 

This is the one I bought:  http://www.ebay.com/...=item2579f144b7

 

satmus

 

satmus: is your stick working by now (openpli4 on vu+duo²)?

I am looking for a DVB-T USB replacement for my physically broken one.

Regards.