Also habe Sundteck Media TV Digital Home und MSI Digivox Mini II v3.0. Beide funktionieren auseinander perfekt, aber zusammen wollen ja überhaupt nicht 
lsusb:
Bus 001 Device 001: ID 1d6b:0002 Bus 002 Device 001: ID 1d6b:0002 Bus 003 Device 001: ID 1d6b:0001 Bus 004 Device 001: ID 1d6b:0001 Bus 001 Device 002: ID 1a40:0101 Bus 001 Device 003: ID 8564:1000 Bus 001 Device 004: ID 15a4:9016 <<< MSI Digivox Bus 001 Device 005: ID eb1a:51b2 <<< Sundteck
lsmod:
Module Size Used by ipv6 341756 20 tda18271 52291 1 af9013 18629 1 dvb_usb_af9015 19633 1 dvb_usb 16074 1 dvb_usb_af9015 brcmfb 1127 2 dvb_bcm7335 4955186 31 brcmfb procmk 1397 1 dvb_bcm7335
dmesg:
fs usbcore: registered new interface driver hub usbcore: registered new device driver usb Advanced Linux Sound Architecture Driver Version 1.0.24. pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101 PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42) pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff]) pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref] Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Switching to clocksource upg cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 32 JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. fuse init (API version 7.17) msgmni has been set to 269 io scheduler noop registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A console [ttyS0] enabled, bootconsole disabled serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A loop: module loaded sata_brcmstb 0000:01:00.0: version 4.0 brcm-pm: enabling sata clocks PCI: Enabling device 0000:01:00.0 (0000 -> 0003) PCI: Setting latency timer of device 0000:01:00.0 to 64 scsi0 : sata_brcmstb scsi1 : sata_brcmstb ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42 ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42 Broadcom STB NAND controller (BrcmNand Controller) bcmemac: Broadcom STB 10/100 EMAC driver v3.0 bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:02:62:47) bcmemac: not registering interface #1 at 0x10090000 (no PHY detected) usbcore: registered new interface driver zd1201 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver brcm-pm: enabling usb clocks ehci-brcm ehci-brcm.0: Broadcom STB EHCI ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300 ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ehci-brcm ehci-brcm.1: Broadcom STB EHCI ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500 ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-brcm ohci-brcm.0: Broadcom STB OHCI ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3 ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci-brcm ohci-brcm.1: Broadcom STB OHCI ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4 ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage ata1: SATA link down (SStatus 4 SControl 300) USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice i2c /dev entries driver lirc_dev: IR Remote Control driver registered, major 254 IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR RC5 (streamzap) protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR LIRC bridge handler initialized Linux video capture interface: v2.00 Bluetooth: Generic Bluetooth USB driver ver 0.6 usbcore: registered new interface driver btusb usb 1-2: new high speed USB device number 2 using ehci-brcm usbcore: registered new interface driver usbhid usbhid: USB HID core driver ALSA device list: No soundcards found. TCP cubic registered NET: Registered protocol family 17 Bluetooth: HIDP (Human Interface Emulation) ver 1.2 lib80211: common routines for IEEE802.11 drivers lib80211_crypt: registered algorithm 'NULL' EBI CS0: setting up NAND flash (primary) mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000001 B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0 brcmnand_read_id: CS0: dev_id=ecf10095 After: NandSelect=40000101, nandConfig=55042200 Block size=00020000, erase shift=17 NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0 Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d, tim2=00000d94 BrcmNAND version = 0x0201 128MB @00000000 B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0 brcmnand_read_id: CS0: dev_id=ecf10095 After: NandSelect=40000101, nandConfig=55042200 Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0 brcmnand_scan: B4 nand_select = 40000101 brcmnand_scan: After nand_select = 40000101 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000 hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0xFF for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0xFF for chip on CS0 nand_read_bbt: Bad block at 0x04be0000 Creating 7 MTD partitions on "brcmnand.0": 0x000000000000-0x000007600000 : "rootfs" 0x000007600000-0x000007a00000 : "kernel" 0x000007a00000-0x000007c00000 : "boot" 0x000007c00000-0x000007d00000 : "cfe" 0x000007d00000-0x000007d80000 : "mac" 0x000007d80000-0x000007e00000 : "env" 0x000007e00000-0x000007f00000 : "nvm" UBI: attaching mtd0 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 usb 1-1: new high speed USB device number 3 using ehci-brcm scsi2 : usb-storage 1-1:1.0 usb 1-2.1: new high speed USB device number 4 using ehci-brcm Afatech DVB-T 2: Fixing fullspeed to highspeed interval: 16 -> 8 input: Afatech DVB-T 2 as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.1/1-2.1:1.1/input/input0 generic-usb 0003:15A4:9016.0001: input,hidraw0: USB HID v1.01 Keyboard [Afatech DVB-T 2] on usb-ehci_hcd-2.1/input1 usb 1-2.4: new high speed USB device number 5 using ehci-brcm UBI: max. sequence number: 499 UBI: attached mtd0 to ubi0 UBI: MTD device name: "rootfs" UBI: MTD device size: 118 MiB UBI: number of good PEBs: 943 UBI: number of bad PEBs: 1 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 943 UBI: number of PEBs reserved for bad PEB handling: 9 UBI: max/mean erase counter: 3/0 UBI: image sequence number: 1506496397 UBI: background thread "ubi_bgt0d" started, PID 48 scsi 2:0:0:0: Direct-Access JetFlash Transcend 4GB 1100 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB) scsi: killing requests for dead queue sd 2:0:0:0: [sda] Write Protect is off scsi: killing requests for dead queue scsi: killing requests for dead queue scsi: killing requests for dead queue scsi: killing requests for dead queue scsi: killing requests for dead queue scsi: killing requests for dead queue sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 sd 2:0:0:0: [sda] No Caching mode page present sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page present sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page present sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATA-8: SAMSUNG HD105SI, 1AJ10001, max UDMA/133 ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD105SI 1AJ1 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 1:0:0:0: [sdb] Attached SCSI disk UBIFS: parse sync UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 116690944 bytes (113956 KiB, 111 MiB, 919 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) on device 0:13. devtmpfs: mounted Freeing unused kernel memory: 240k freed EXT4-fs (sda1): recovery complete EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sdb1): warning: mounting fs with errors, running e2fsck is recommended EXT4-fs (sdb1): recovery complete EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) procmk_init dvb_bcm7335: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint DVB: registering new adapter (bm750) bcm7335: hotplug_callback(): Hotplug - status.connected 1 bcm7335: hotplug_callback(): Hotplug - connecting HDMI to display 0xe brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $ [VID]: <6>bcm7335_video_init [AUD]: <6>bcm7335_audio_init DVB: registering adapter 0 frontend 0 (BCM7335 FE)... DVB: registering adapter 0 frontend 0 (BCM7335 FE)... [MPVR]: >> misc_pvr_init input: dreambox advanced remote control (native) as /devices/virtual/input/input1 [LCD]: registered [0;35m[CI]:[0;0m-BM750_PCB_2_1 [CI]: registered ci0 [CI]: registered ci1 [DFP]: registered dbox fp [DFP]: bcm7335_i2c_write: Error 1114113 [DFP]: bcm7335_max_i2c_write: Error 1114113 [DFP]: Scart 4707 is found 4 [SC]: registered sci0 [SC]: registered sci1 system_time_set wakeup mode get system_time_set wakeup mode get 0xc4 dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in cold state, will try to load a firmware dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Afatech AF9015 DVB-T USB2.0 stick) af9013: firmware version:4.95.0.0 DVB: registering adapter 1 frontend 0 (Afatech AF9013 DVB-T)... tda18271 0-00c0: creating new instance TDA18271HD/C2 detected @ 0-00c0 Registered IR keymap rc-msi-digivox-ii input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.1/rc/rc0/input2 rc0: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.1/rc/rc0 dvb-usb: schedule remote query interval to 500 msecs. dvb-usb: Afatech AF9015 DVB-T USB2.0 stick successfully initialized and connected. usbcore: registered new interface driver dvb_usb_af9015 Adding 131068k swap on /media/usb/swapfile. Priority:-1 extents:3 across:143356k [VID]: VIDEO_SET_STREAMTYPE 0 [VID]: VIDEO_SELECT_SOURCE 1 [VID]: VIDEO_PLAY 1 2 0 [VID]: VIDEO_CONTINUE 1 1 [VID]: VIDEO_CLEAR_BUFFER 1 1 0 [VID]: VIDEO_STOP 0 1 [VID]: VIDEO_SELECT_SOURCE 0 NET: Registered protocol family 10 DVB: registering adapter 0 frontend 0 (Sundtek DVB-C (0/0))... eth0: no IPv6 routers present [VID]: VIDEO_SET_STREAMTYPE 0 [VID]: VIDEO_SELECT_SOURCE 1 [VID]: VIDEO_PLAY 1 2 0 [VID]: VIDEO_CONTINUE 1 1 [VID]: VIDEO_CLEAR_BUFFER 1 1 0 [VID]: VIDEO_STOP 0 1 [VID]: VIDEO_SELECT_SOURCE 0 [CI]:ci_dev_open [CI]:Opening A GPIO's for 7335 platform [CI]:Opening A GPIO's for 7335 platform....done [CI]:entering.. A NEXUS_DvbCi_Open [CI]:NEXUS_DvbCi_Open done.. [CI]:Installing callbacks [CI]:Forcing card check [CI]:Card insertion status changed [CI]:Opening B GPIO's for 7335 platform [CI]:Opening B GPIO's for 7335 platform....done [CI]:entering.. B NEXUS_DvbCi_Open [CI]:NEXUS_DvbCi_Open done.. [CI]:Installing callbacks [CI]:Forcing card check [CI]:Card B insertion status changed [CI]: CI interface initialised [CI]:ci1_dev_open [CI]:NEXUS_Remux_Start CI0 0 0 [CI]:>>close_mpod tuner:0 [CI]:remux stop [CI]:get_remux_startcnt() count : 1 [CI]:get_remux_startcnt() count : 1 [CI]:>>close_mpod tuner:1 [CI]:remux stop [CI]:get_remux_startcnt() count : 0 [CI]:get_remux_startcnt() count : 0 tda18271: performing RF tracking filter calibration tda18271: RF tracking filter calibration complete CIFS VFS: default security mechanism requested. The default security mechanism will be upgraded from ntlm to ntlmv2 in kernel release 3.2 [AUD]: AUDIO_SET_MUTE 0 [AUD]: AUDIO_SET_MIXER -2026471952 [AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0 [AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0 [AUD]: AUDIO_SET_MIXER : next left volume -200, right volume -200 [AUD]: AUDIO_SET_MIXER -2026471952 [AUD]: AUDIO_SET_MIXER : amixl 41, amixr 41 [AUD]: AUDIO_SET_MIXER : next left volume -200, right volume -200 [AUD]: AUDIO_SET_MIXER : next left volume -3128, right volume -3128 [AUD]: AUDIO_SET_BYPASS_MODE 1 [AUD]: downmix 0 state : 0 [AUD]: AUDIO_PAUSE 6887504 [AUD]: AUDIO_PLAY 6887504 decoder start : 0 [VID]: VIDEO_GET_SIZE src w: 1280 h:720 display w:1280 h:720 [VID]: VIDEO_GET_SIZE aspect: 1 6 [VID]: VIDEO_SET_STREAMTYPE 1 [VID]: VIDEO_FREEZE 6887504 0 [VID]: VIDEO_PLAY 6887504 5 2 [VID]: VIDEO_SLOWMOTION 0 1 [VID]: VIDEO_FAST_FORWARD 0 1 [VID]: VIDEO_CONTINUE 6887504 1 [AUD]: AUDIO_CONTINUE 6887504 1 audio pid_hndl : 0xc0b5b0dc [AUD]: setting mute : 0 [AUD]: AUDIO_CHANNEL_SELECT 0 EXT4-fs (sdb1): error count: 1185 EXT4-fs (sdb1): initial error at 1343820535: ext4_mb_generate_buddy:738 EXT4-fs (sdb1): last error at 1378406784: ext4_lookup:1044: inode 540419
Wie bringe ich die beide zusammen zum laufen? Kann jemand bitte helfen.
