Loop na de update tegen de hierboven genoemde error aan FTP op poort 21 telnet en SSH poort 23 en 22 werken wel. Na backup terug zetten werkt alles weer na update van vandaag wederom niet.
Posted 7 October 2013 - 10:16
Loop na de update tegen de hierboven genoemde error aan FTP op poort 21 telnet en SSH poort 23 en 22 werken wel. Na backup terug zetten werkt alles weer na update van vandaag wederom niet.
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 7 October 2013 - 10:19
Zo te zien met telnet klopt t dat de folder vsftpd mist
Edited by 40H3X, 7 October 2013 - 10:19.
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 7 October 2013 - 10:19
Hier geen enkel probleem.
Waarschijnlijk een al wat oudere OpenPLi 4 installatie, waarin een defecte FTP deamon zat. Opnieuw flashen met de laatste lost dat op (een update niet, omdat het deel is van de image).
Als je avontuurlijk aangelegd bent zou je ook nog kunne doen:
opkg remove vsftpd opkg install vsftpd
en dan je oude config weer terugzetten.
edit: die folder hoort er ook niet te zijn...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 7 October 2013 - 10:24
ga hem zo flashen
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 7 October 2013 - 10:41
Klopt na flash keurig bereikbaar met ftp
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 7 October 2013 - 10:45
Klopt t dat er standaard in de flash geen CCcam 2.3.0 zit alleen de setup?
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
Posted 7 October 2013 - 11:03
Als je na de flash zonder autobackup/autoinstall de setup Wizard doorloopt moet je de vraag krijgen of CCcam geinstalleerd moet worden. Gebeurt dat niet?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 7 October 2013 - 11:35
Neen na een flash start PLi op en is alles (software en settings) excl. CCcam ik zie geen wizard
Hardware: Vu+ Uno 4K SE - Vu+ Duo 4K - Fuba 78 cm - Tripleblock LNB Quad 19.2/23.5/28.2 - DS918+
Software : OpenPLi - OSCam - Settings van Hans - Autotimer - EPGImport
---------------------------------------------------------------------------------------------------------------------------------------
Remember: Upvote with the button for any user/post you find to be helpful, informative, or deserving of recognition!
---------------------------------------------------------------------------------------------------------------------------------------
Many answers to your question can be found in our new and improved wiki
0 members, 5 guests, 0 anonymous users