Hi, i want to use clone+ on my reciver "vu+ solo2" but the voltage in the CA module is to low (the clone+ card wont lit)
I there any way to alter this voltage on CA module?
VOLTAGE ON CA MODULE VU+ SOLO2
Started by inhu, 04 Nov 2013 15:56
14 replies to this topic
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #3
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 7 November 2013 - 17:26
What do you mean by 'CA module'?
The CI interface, or the smartcard interface?
(I fear that in both cases though, there is no way to change the voltage)
And which is the voltage, and what voltage would you like to have?
The CI interface, or the smartcard interface?
(I fear that in both cases though, there is no way to change the voltage)
And which is the voltage, and what voltage would you like to have?
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #4
-
- PLi® Contributor
- 6,100 posts
+260
Excellent
Posted 8 November 2013 - 09:52
Moreover checking how Clone+ device works show that it doesn't use the PCMCIA slot but it uses Wifi smartcard.
So voltage of the PCMCIA slot is not a relevant question in the context of Clone+
You will still a softcam to enable the interncal card reader and insert the "fake" smartcard in the card reader, not in the PCMCIA.
So i guess that by CA you mean card reader?
Pr2
Edited by Pr2, 8 November 2013 - 09:53.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #5
-
- Member
- 8 posts
0
Neutral
Posted 8 November 2013 - 11:27
Sorry!. I ment the smartcard interface (the smartcard reader in vu+ solo2 reciver).
The problem is that the clone card, which i put in the solo2 smartcard reader needs a few volts to work. Im not sure how much voltage, but my plan was to increse the voltage in small amounts.
BTW. The clonecards works with my sagem pvr101 reciver. And the card is turned correctly.
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #6
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 8 November 2013 - 12:50
With that kind of reasoning, you might as well try to increase the frequency, temperature, or airpressure 
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #7
-
- Member
- 8 posts
0
Neutral
Posted 8 November 2013 - 13:09
I just want my clone+ card to work. I read that a smart card needs 5v on the Vcc circuit.
http://www.tldp.org/...sification.html
Edited by inhu, 8 November 2013 - 13:12.
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #8
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 8 November 2013 - 13:10
and 5V just happens to be the default for smartcard readers
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #9
-
- Member
- 8 posts
0
Neutral
Posted 8 November 2013 - 15:05
Then I dont understand why the card works on my older reciver.
The leds on the clone+ card wont lit, even if I try it in different positions (and pressing) on solo2 reciver.
Maby the voltage in solo2 is 4.8V ?!
What is controlling the voltage for the smartcard reader? Hardware or software openPLI?
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #10
-
- PLi® Core member
- 7,185 posts
+323
Excellent
Posted 8 November 2013 - 15:28
Did you try to turn around the card? In some boxes the chip must be down and in some up (sorry haven't found better words for it, I hope you understand what I mean).
Edited by betacentauri, 8 November 2013 - 15:29.
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #11
-
- Member
- 8 posts
0
Neutral
Posted 8 November 2013 - 15:36
Yes, i tried everything 
, turning and pressing on the card in different directions. But no luck.
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #12
-
- PLi® Contributor
- 6,100 posts
+260
Excellent
Posted 8 November 2013 - 15:47
Do you enable a softcam on your box to activate the card reader?
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #13
-
- Member
- 8 posts
0
Neutral
Posted 8 November 2013 - 16:01
Yes, the solo 2 reciver works fine with the original card. And CCcam is enabled.
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #14
-
- Member
- 8 posts
0
Neutral
Posted 11 November 2013 - 10:45
What is controlling the voltage for the smartcard reader in my solo2 reciver? Hardware or software openPLI?
Re: VOLTAGE ON CA MODULE VU+ SOLO2 #15
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 11 November 2013 - 10:58
Hardware
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
