- Format your USB stick with a FAT32 file system
- Download the USB image of your choice (this is an image specific for USB flashing, you can not use the standard .nfi file)
- Extract the USB image (Zip-file) with full path to the root of the USB stick
- Switch your receiver off (power-off, not stand-by)
- Insert the prepared USB stick into the front of the receiver and switch the power on
- During powerup push the ring around the power button to the right or up ( green and yellow led should light up)
- Wait untill the receiver reboots by itself.
- Follow the installation instructions on the screen
ET4000 crash after update
Started by Antonyo, 10 Nov 2013 16:19
28 replies to this topic
Re: ET4000 crash after update #21
-
- Senior Member
- 5,782 posts
+29
Good
Posted 20 February 2014 - 19:25
How to flash from an USB stick
Re: ET4000 crash after update #22
-
- Forum Moderator
PLi® Core member - 14,925 posts
+486
Excellent
Posted 20 February 2014 - 19:55
aha, my mistake, so that setting is only available for vu.
grtz Philip
No, it is only available for the new ET10000, now it it is possible to reduce the fan-noise by decreasing the fanspeed.
Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....
On the edge of the abyss, a step forward is not always progress....
Hardware: 2x Daily used Vu+ Ultimo 4K - Vu+ Duo 4K SE and a lot more.... - VisioSat BiBigsat - Jultec Unicable Multiswitch 4 positions: 19.2/23.5/28.2 East - Diseqc motorized flatdish antenna
Software : HomeBuild OpenPLi Develop and Scarthgap builds, local cards driven by OsCam
Press the 
button on the buttom right of this message 
Have you tried our wiki yet? Many answers can be found in our OpenPLi wiki
Re: ET4000 crash after update #23
-
- Member
- 18 posts
0
Neutral
Posted 21 February 2014 - 01:41
thank you guys,
but...
i did the steps from (1 to 5)
- by (6) i donn't have a ring around the power button.
- i have two push button on the left side of the USB input above each other (C+& C-)
- i pushed C+ button and wait, the yellow light waint out and nothing happend the device steys into the re-starting loop
- i pushed the C- button thating happened.
do any one have any idea whay?
thanks
grt
Ziyad
How to flash from an USB stick
- Format your USB stick with a FAT32 file system
- Download the USB image of your choice (this is an image specific for USB flashing, you can not use the standard .nfi file)
- Extract the USB image (Zip-file) with full path to the root of the USB stick
- Switch your receiver off (power-off, not stand-by)
- Insert the prepared USB stick into the front of the receiver and switch the power on
- During powerup push the ring around the power button to the right or up ( green and yellow led should light up)
- Wait untill the receiver reboots by itself.
- Follow the installation instructions on the screen
Re: ET4000 crash after update #24
-
- Senior Member
- 1,667 posts
+59
Good
Posted 21 February 2014 - 09:48
aha, my mistake, so that setting is only available for vu.
grtz Philip
No, it is only available for the new ET10000, now it it is possible to reduce the fan-noise by decreasing the fanspeed.
on duo2 
Fan speed.jpg 68.9KB
13 downloads
grtz Philip
vuduo2 openpli6.1 1TB HDD 2xdualS2tuner
av receiver denon - samsung 4k hdr+ 65inch UE65MU7000 - bose accoustimas 7.1 
tvv kaart & schotel(64cm), duo lnb, OSCAM
logitech harmony ultimate
Re: ET4000 crash after update #25
-
- Forum Moderator
PLi® Core member - 27,494 posts
+397
Excellent
Posted 21 February 2014 - 11:05
@Zyiad
As we are talking about a 4000, the procedure is almost thesame, but one thing different. After power up with the stick placed in the box, you should push the small button in the left upper corner behind the cover. Then flashing will succeed.
As we are talking about a 4000, the procedure is almost thesame, but one thing different. After power up with the stick placed in the box, you should push the small button in the left upper corner behind the cover. Then flashing will succeed.
Mijn schotel is een T90 met 10 LNB's. Daarnaast voor de fun nog een draaibaar systeem met een Triax TD 78.
Dreamboxen heb ik niet meer echt actief. Verder heb ik ook nog een een VU+ duo2 met 500Gb harddisk + een VU+ Uno, Zero, Solo 4K, Ultimo 4K, Zero 4K, Uno 4Kse. + ook nog een Xtrend ET7x00. Daarnaast heb ik ook nog diverse andere modellen w.o. een Formuler F4, ET8500, ET7500, Mut@nt 2400HD, Xsarius Fusion HD se en verder nog wel het e.e.a. waarmee op verzoek vanalles wordt getest. Iemand moet het tenslotte doen. 
Los van de eerder genoemde modellen heb ik nog wel een rits aan testsamples als Mut@nt 2400HD, HD60, GB UE4K, GB Trio4K, Maxitec Multibox combo en Twin, Octagon sf8008, sf8008 mini en last but nog least enkele modellen van het Grieks Duitse Edision.
Voor centrale opslag van media gebruik ik een Qnap 219P met tweemaal 2 Tb harddisks + een Synology DS414 met 12 Tb Totale opslag.
-------------------------------------------------------------------------------------------
Many answers to your question can be found in our wiki: Just one click away from this "solutioncentre".
Als ik alles al wist hoefde ik ook niets te vragen. If I had all the knowledge I had no questions at all.
Re: ET4000 crash after update #26
-
- Member
- 18 posts
0
Neutral
Posted 21 February 2014 - 12:50
Hallo All,
I did do all the steps:
- formated flash FAT32
- Ihave 4 documents in the flaf( not in (et4000) file)
- imageversion/ 1KB
- noforce/ 1KB
- kernel{{VLC Media file(.bin) 4,035 KB}}
- rootfs{{ VLC media file(.bin) 57,216}}
- I did all the steps, but again without any luck
dus any body live in Netherland near Rotterdam can help me with that.
thanks
Re: ET4000 crash after update #27
-
- Senior Member
- 4,774 posts
+69
Good
Posted 21 February 2014 - 13:26
Je moet een map et4000 hebben waarin deze bestanden staan op je usb stick
Groetjes Cobus R
VU+ UNO 4K SE FBC DVB-C (8x)
MUTANT HD66SE FBC DVB-C (3x)
MAXYTEC MULTIBOX COMBO
MUTANT HD60 DVB-S
Ziggo (digitaal) Kabel TV (FTV) op alle decoders met oa fallback tuner
Re: ET4000 crash after update #28
-
- Senior Member
- 1,667 posts
+59
Good
Posted 21 February 2014 - 13:57
Je moet een map et4000 hebben waarin deze bestanden staan op je usb stick
indeed, you have to put the complete folder et4x00 on the usb, not just the 4 documents.
if you check de usb there hase to be a folder(et4x00) on it with in that folder the 4 documents.
grtz Philip
vuduo2 openpli6.1 1TB HDD 2xdualS2tuner
av receiver denon - samsung 4k hdr+ 65inch UE65MU7000 - bose accoustimas 7.1
tvv kaart & schotel(64cm), duo lnb, OSCAM
logitech harmony ultimate
Re: ET4000 crash after update #29
-
- Member
- 18 posts
0
Neutral
Posted 21 February 2014 - 18:59
Guys,,,, 
,,
now i Know why i can not flash it before, i did flash it and now he works again, thank you guys for everything,
now i have the first problem,
my et4000 crased every time i tried to open something on youtube? where can i find the loggon file so i can attached it to you guys?
New challenge>>> can we uplaod a complete setting & configration for ET4000? if yes can i get this file from one of you guys?
if the file so big you can send it to my DROPBOX
thank you guys
.
Je moet een map et4000 hebben waarin deze bestanden staan op je usb stick
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
