Jump to content


Photo

How to Access to a LAN Drive (with user and psw) to play movies

Started by toxstoxs, 05 Feb 2014 18:29

  • Please log in to reply
4 replies to this topic

#1 toxstoxs

  • Member
  • 33 posts

0
Neutral

Posted 5 February 2014 - 18:29

Hi everyone

 

I'm trying to find the way to map on my DM800 se my nework drive where i host all my movies.

 

Both DM and Network Drive are of course on same IP mark (192.168.x.x)

 

The network drive is password protected (user and psw that i can set according to my wish).

 

I been trying to install the SMB extention from feed.. but it cause a green screen with boot loop... ( i had to flash the latest 05/02 image to make it work again).

 

Can anybody gave me some tips?

 

Is there a easy plug in to access my drive?

 

About the drive is a 4TB EXT4 formatted.

 

I hope you can help me.

 

Regards


Edited by toxstoxs, 5 February 2014 - 18:30.

Re: How to Access to a LAN Drive (with user and psw) to play movies #2 WanWizard

  • PLi® Core member
  • 70,562 posts

+1,813
Excellent

Posted 5 February 2014 - 20:41

What is a "network drive"? A NAS system? A remote PC or server?

 

All software required to make a mount (a mapping) from the box to a server is already present, there is no need to install anything.

 

You can use the mount manager and/or the network browser (you'll find them under menu - setup - network) to make a connection to a drive in a remote server or NAS.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.

Re: How to Access to a LAN Drive (with user and psw) to play movies #3 toxstoxs

  • Member
  • 33 posts

0
Neutral

Posted 5 February 2014 - 20:48

Yes.. i wasn't enought clear.. sorry...

 

it's a NAS

 

i followed the mount process but had a lot of trouble to access the resource even after mounted the network folder..

 

I gave IP username and psw

 

but once mapped and mounted the relative path beside it's green Flagged as Active it carry a RED cross...

 

and i can't see the files inside the mounted location.

 

Any idea?


Re: How to Access to a LAN Drive (with user and psw) to play movies #4 WanWizard

  • PLi® Core member
  • 70,562 posts

+1,813
Excellent

Posted 5 February 2014 - 21:11

No, sorry, I never used them to make a mount. Perhaps someone else?


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.

Re: How to Access to a LAN Drive (with user and psw) to play movies #5 Pr2

  • PLi® Contributor
  • 6,182 posts

+261
Excellent

Posted 6 February 2014 - 13:56

The easiest way is to go into network parameters and select: network browser it will show you the list of discovered device and then you can easily mount the shares from there.


NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.

Wanna help with OpenPLi Translation? Please read our Wiki Information for translators

Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)

AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
 

Back to [EN] Enduser support

1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users

  1. Forums
  2. → PLi® Support
  3. → [EN] Enduser support