693 replies to this topic

[tilleke]

vlc streaming port 8001 works, port 8002 doesnt work

 

Port 8002 with streaming-authentication works fine here using VLC 2.0.6 Twoflower (haven't tried the later versions). This was using OpenPLi-4.0-beta-vuduo2-20140512_usb.zip on my Duo2.

 

Hint: you would be better off perhaps using the new syntax mentioned earlier in this thread (the OWIF-m3u file still uses the original syntax)

Edited by tilleke, 12 May 2014 - 22:27.

[колбаскин]

Port 8002 with streaming-authentication works fine here using VLC 2.0.6 Twoflower (haven't tried the later versions).

 

On mobile phone ? Work fine on Android?

 

 

Hint: you would be better off perhaps using the new syntax mentioned earlier in this thread (the OWIF-m3u file still uses the original syntax)

 

Give me link please, how fix this?

 

In russian:

Господа программисты, почините пожалуйста работу транскодинга на порту 8002. Он не работает на любом плеере установленном на Android. На компьютере он открывается плеером VLC только со второго раза. Вы испортили стрим с транскодингом. Верните настройку при помощи плагина. Вы все только портите. Вы стали хуже BH.

[Erik Slagter]

Taboune, do the following:

 

killall streamproxy

streamproxy -f

 

now do again what you do and send the output (via pm if it contains passwords).

 

It looks like certain vlc versions have a bug in this area.

[delavega]

it was working before with my current vlc no need to use an old assed version of vlc

 

this is getting annyoing

[delavega]

Taboune, do the following:

 

killall streamproxy

streamproxy -f

 

now do again what you do and send the output (via pm if it contains passwords).

 

It looks like certain vlc versions have a bug in this area.

ok 

[delavega]

sent

Edited by taboune, 13 May 2014 - 14:02.

[Erik Slagter]

root@vusolo2:~# killall streamproxy
killall: streamproxy: no process killed

This is weird, it says streamproxy isn't running at all. It may be that your startup scripts have been damaged. Please restart (completely and not just enigma) and then type ps | fgrep streamproxy. It should be running then.

[delavega]

now its get killed yes but its still the same problem cant stream from port 8002 to vlc

 

ClientSocket: exception: Encoder: missing pmt, video or audio pid

streamproxy: pid 517 exited

Edited by taboune, 13 May 2014 - 14:52.

[Erik Slagter]

streamproxy: config_map: auth = false/0 

This says no authentication requirement is found. So apparently you have "use authentication for streaming = off" in the open webif settings. If that setting is off, no attempt is done using authentication towards the web interface (which it needs for tuning, allocating demux etc), which is fine, if the webif is also configured to not use authentication for streaming (which normally is no problem, because both programs use/check the same option).

 

There is one note though, if you CHANGE the setting in the open webif plugin, you need to restart enigma. Why is that: that's because enigma only writes out configuration options (/etc/enigma2/settings) when it's stopped. And only then, the streamproxy can pick up the new value (which it will do automatically).

[delavega]

authentication for streaming  is already off

[Erik Slagter]

WebifRequest: send request to webif: "GET /web/stream?StreamService=1:0:1:200A:430:1:C00000:0:0:0 HTTP/1.0

"
ClientSocket: exception: Encoder: missing pmt, video or audio pid

This means the request to the web interface didn't give an answer. This can happen (in my experience) if a service cannot be tuned to by enigma, or if the web interface expects authentication while streamproxy doesn't know it has to supply it.

 

Please do:

 

restart enigma

fgrep auth /etc/enigma2/settings

 

to see what authentication settings are actually active.

[Erik Slagter]

You can check if it's supposed to work bypassing the streamproxy using vlc on a pc:

 

vlc "http://<stb>:8001/1:0:1:200A:430:1:C00000:0:0:0" (I guess this should work, with mplayer this works)

[delavega]

root@vusolo2:~# fgrep auth /etc/enigma2/settings

config.OpenWebif.auth=true

[delavega]

well fuck port 8002 anyways im gonna stick with 8001 then

[Erik Slagter]

If you turn that off it will probably work (although this combination probably should work, I am not sure, that depends on whether the openwebif requires authentication on the /web/StreamService url using this setting, I guess it shouldn't).

[Erik Slagter]

well fuck port 8002 anyways im gonna stick with 8001 then

Yet another happy customer!

[delavega]

port 8001 always worked and auth for streaming was forever off

[delavega]

i have a backup from last week where port 8002 works

[Erik Slagter]

I have a current updated image where port 8002 works.

[delavega]