Jump to content


Photo

Transcoding problem


  • Please log in to reply
693 replies to this topic

Re: Transcoding problem #601 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 30 May 2014 - 16:05

All the people that have problems, did you make changes to the /etc/enigma2/streamproxy.conf file? If so, can you post it?

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #602 Rob van der Does

  • Senior Member
  • 7,766 posts

+184
Excellent

Posted 30 May 2014 - 16:09

The only thing I did was changing the bitrate via the app (from 1mbs to 50kbs).
In all other images I tried this works flawless (I understand that doesn't help you, but just to underline that in itself the Solo2 should do a fine job).
The first tow times I changed the bitrate I was surprised to see no difference in PQ after the stream had restarted. When I use 50kbs in other images the PQ is really bad. So it looks like the new setting isn't actually applied.

Re: Transcoding problem #603 Rob van der Does

  • Senior Member
  • 7,766 posts

+184
Excellent

Posted 30 May 2014 - 16:12

All the people that have problems, did you make changes to the /etc/enigma2/streamproxy.conf file? If so, can you post it?

I did not. Just a fresh flashed PLi with basic settings to get the image running.

Re: Transcoding problem #604 SpaceRat

  • Senior Member
  • 1,030 posts

+65
Good

Posted 30 May 2014 - 16:19

The first tow times I changed the bitrate I was surprised to see no difference in PQ after the stream had restarted. When I use 50kbs in other images the PQ is really bad. So it looks like the new setting isn't actually applied.

That's normal.

Neither does Erik's transproxy use settings inside /etc/enigma2/settings (Let alone ones that would be compatible to the Vu+ transproxy) nor does his proxy allow reliable detection of itself (Which would allow OWIF or a plugin to configure it).

So the only way to configure it is the manual way inside /etc/enigma2/streamproxy.conf

Well, to be precise there is a second one through parameters in the URL, but without a reliable detection mechanism at hand, nobody will support it.
1st box: Vu+ Ultimo 4k 4xDVB-S2 FBC / 2xDVB-C / 1.8 TB HDD / OpenATV 6.2
2nd box: Gigablue Quad 4k 2xDVB-S2 FBC / 2xDVB-C / 1.8 TB HDD / OpenATV 6.2
testing boxes: Vu+ Duo² + AX Quadbox HD2400 + 2x Vu+ Solo² + Octagon SF4008
Sats & Pay-TV: Astra 19.2°E + Hotbird 13°E with Redlight / SCT HD / SES Astra HD- / Sky V14 / 4th empire propaganda TV
Card-Server: Raspberry Pi + IPv6-capable oscam
Router: Linksys WRT1900ACS w/ LEDE + Fritz!Box 7390

Re: Transcoding problem #605 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 30 May 2014 - 16:23

http://your_receiver...eb?request=info

http://your_receiver...uest=info&xml=1

 

The VU+ transtreamproxy and filestreamproxy don't use any setting from enigma at all. They're dependent on the plugin for setting the parameters, globally.


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #606 SpaceRat

  • Senior Member
  • 1,030 posts

+65
Good

Posted 30 May 2014 - 16:39

http://your_receiver...eb?request=info
http://your_receiver...uest=info&xml=1

This is not a proper way to detect the operating mode for transcoding.
Don't rely on my words for it, just accept the fact that also nobody else supports it (e.g. in their Android/Crapple apps).

 

The VU+ transtreamproxy and filestreamproxy don't use any setting from enigma at all. They're dependent on the plugin for setting the parameters, globally.

That's a purely academic discussion, just like that about Linux being only the kernel.
1st box: Vu+ Ultimo 4k 4xDVB-S2 FBC / 2xDVB-C / 1.8 TB HDD / OpenATV 6.2
2nd box: Gigablue Quad 4k 2xDVB-S2 FBC / 2xDVB-C / 1.8 TB HDD / OpenATV 6.2
testing boxes: Vu+ Duo² + AX Quadbox HD2400 + 2x Vu+ Solo² + Octagon SF4008
Sats & Pay-TV: Astra 19.2°E + Hotbird 13°E with Redlight / SCT HD / SES Astra HD- / Sky V14 / 4th empire propaganda TV
Card-Server: Raspberry Pi + IPv6-capable oscam
Router: Linksys WRT1900ACS w/ LEDE + Fritz!Box 7390

Re: Transcoding problem #607 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 30 May 2014 - 20:28

http://your_receiver...eb?request=info
http://your_receiver...uest=info&xml=1

This is not a proper way to detect the operating mode for transcoding.

 

Before you start yelling again, yes no single app uses the extra features of the streamproxy. That's a shame, but it was to be expected (at least in the short run). Nobody wants to keep apdapting it's code to every image/implementation, which is understandable. It has nothing to do with "detection". Maybe at some time some app builders will start to see the advantage to users of http byte range access and to be able to seek to time offsets within a file.

 

The VU+ transtreamproxy and filestreamproxy don't use any setting from enigma at all. They're dependent on the plugin for setting the parameters, globally.

That's a purely academic discussion, just like that about Linux being only the kernel.

 

Maybe, but in this context it is actually relevant. See the context.


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #608 tilleke

  • Senior Member
  • 50 posts

+5
Neutral

Posted 30 May 2014 - 20:50

Erik, you're wrong! Vu+ Players uses it and you know it.   :)



Re: Transcoding problem #609 колбаскин

  • Senior Member
  • 105 posts

+1
Neutral

Posted 31 May 2014 - 07:40

Erik maybe you return the plugin for normal work with VU+ Player (with settings for transcoding on mobile?) :rolleyes:



Re: Transcoding problem #610 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 31 May 2014 - 09:15

Erik, you're wrong! Vu+ Players uses it and you know it.   :)

Yes I know it ;) I was speaking in very (too) general terms.


Edited by Erik Slagter, 31 May 2014 - 09:18.

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #611 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 31 May 2014 - 09:17

Erik maybe you return the plugin for normal work with VU+ Player (with settings for transcoding on mobile?) :rolleyes:

What do you think? Do you really think that would solve the problems? Dream on.

 

Why don't I see (like requested "some" times earlier)

- a proper bug report including boxtype and app used

- output of the streamproxy when run in foreground

- dmesg output

 

Like I said, nothing has changed for about two weeks now.


Edited by Erik Slagter, 31 May 2014 - 09:34.

* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #612 delavega

  • Senior Member
  • 377 posts

+2
Neutral

Posted 31 May 2014 - 09:25

its still working for me since then. :D


<p><span style="font-size:18px;"><span style="font-family:'lucida sans unicode', 'lucida grande', sans-serif;"><strong>Vu+ DUO 2</strong></span></span></p>
<p><span style="font-size:18px;"><span style="font-family:'lucida sans unicode', 'lucida grande', sans-serif;"><strong>Vu+ SOLO</strong></span></span>

Re: Transcoding problem #613 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 31 May 2014 - 09:34

its still working for me since then. :D

Thanks for the report. Didn't test it on the solo2 lately.


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #614 Chelsea

  • Member
  • 47 posts

0
Neutral

Posted 3 June 2014 - 20:56

Are there soon any solution for the transcoding problem on Vu+ Duo2 ?

 

I still have big problem with streaming my channels, specially the HD channels.

 

The problem I had are:

 

Lagging/Micro freezes

Bad quality

Streaming ends



Re: Transcoding problem #615 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 4 June 2014 - 15:04

If you can start a session successfully, that is were our input to the process ends. The whole transcoding itself is done in hardware and controlled by drivers which are developed by VU+.

 

But this sounds like a bad network connection / bad wireless reception. You might want to try a lower bit rate.


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #616 Chelsea

  • Member
  • 47 posts

0
Neutral

Posted 4 June 2014 - 19:40

If you can start a session successfully, that is were our input to the process ends. The whole transcoding itself is done in hardware and controlled by drivers which are developed by VU+.

 

But this sounds like a bad network connection / bad wireless reception. You might want to try a lower bit rate.

Sorry byt I do not use wireless connection at all.

My network are working very well.

 

I do not have any problem at all with Black Hole, but I do not like Back Hole, so I hope this will be fixed in OpenPli. J



Re: Transcoding problem #617 Kers

  • Member
  • 43 posts

+2
Neutral

Posted 5 June 2014 - 13:01

I'm having problems with transcoding on Duo2, it worked for a while but stopped in the past week or two.

 

When I open the stream with VLC, I can see that its receiving some data, but the picture stays blank. I can see that its receiving data in the "input/read" section, but the decoded section stays at 0.

Codec part says that its a H264 + AAC stream, as it should.

 

Any idea what might be wrong?

 

Here is what /var/log/messages says:

Jun  5 13:53:13 vuduo2 user.warn streamproxy: streamproxy: accept new connection on port 8002, default action: transcode, fd 6
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: range requested from: 0
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: header[connection]: "close"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: header[host]: "vu2:8002"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: header[icy-metadata]: "1"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: header[range]: "bytes=0-"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: header[user-agent]: "VLC/2.1.4 LibVLC/2.1.4"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: url: /1:0:1:2756:7FC:2:11A0000:0:0:0:
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: parameter[] = "/1:0:1:2756:7FC:2:11A0000:0:0:0:"
Jun  5 13:53:13 vuduo2 user.warn streamproxy: Service: create service: 1:0:1:2756:7FC:2:11A0000:0:0:0
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: default live request
Jun  5 13:53:13 vuduo2 user.warn streamproxy: ClientSocket: transcoding service
Jun  5 13:53:13 vuduo2 user.warn streamproxy: LiveTranscoding: 1:0:1:2756:7FC:2:11A0000:0:0:0
Jun  5 13:53:13 vuduo2 user.warn streamproxy: WebifRequest: send request to webif: "GET /web/stream?StreamService=1:0:1:2756:7FC:2:11A0000:0:0:0 HTTP/1.0^M ^M "
Jun  5 13:53:13 vuduo2 user.warn kernel: FE tune
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[audio] = d05
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[audio-1] = d06
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[pat] = 0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[pcr] = d04
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[pmt] = 106
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[subtitle] = 938
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[subtitle-1] = 939
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[text] = 938
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: pid[video] = d04
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Encoder: encoder 0 in use: 0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Encoder: encoder 1 in use: 0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: setprop: display_format=480p
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Encoder: bitrate: 500/500000
Jun  5 13:53:14 vuduo2 user.warn streamproxy: setprop: bitrate=500000
Jun  5 13:53:14 vuduo2 user.warn streamproxy: setprop: profile=baseline
Jun  5 13:53:14 vuduo2 user.warn streamproxy: setprop: level=3.1
Jun  5 13:53:14 vuduo2 user.warn streamproxy: setprop: gop_frameb=0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Encoder: open encoder /dev/bcm_enc0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: pmt: 262
Jun  5 13:53:14 vuduo2 user.warn streamproxy: video: 3332
Jun  5 13:53:14 vuduo2 user.warn streamproxy: audio: 3333
Jun  5 13:53:14 vuduo2 user.warn streamproxy: start ioctl
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: encoder pid[audio] = d05
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: encoder pid[pat] = 0
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: encoder pid[pmt] = 106
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: encoder pid[video] = d04
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Demuxer: ioctl demuxer ADD PID: audio -> 0xd05
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Demuxer: ioctl demuxer ADD PID: pmt -> 0x106
Jun  5 13:53:14 vuduo2 user.warn streamproxy: Demuxer: ioctl demuxer ADD PID: video -> 0xd04
Jun  5 13:53:14 vuduo2 user.warn streamproxy: LiveTranscoding: state init -> starting
Jun  5 13:53:16 vuduo2 user.warn streamproxy: LiveTranscoding: state starting -> running
 

 



Re: Transcoding problem #618 Erik Slagter

  • PLi® Core member
  • 46,969 posts

+541
Excellent

Posted 5 June 2014 - 14:47

This says transcoding is taking place sucessfully.

 

At this moment the output of "dmesg" is more interesting. It may very well be that the transcoding engine has crashed. This is very typical when no stream is received.


* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.


Re: Transcoding problem #619 Kers

  • Member
  • 43 posts

+2
Neutral

Posted 5 June 2014 - 15:41

 
It seems that the stream actually does come, but is somehow not understood by linux VLC 2.1.4.
When I opened it with BS Player on my android mobile it worked, but VLC does now decode it even though its getting the data and recognizes the codec.
If I download the playlist file and open it from the commandline with vlc, I get the error "MPEG-4 descriptor not found". Maybe thats why its not displaying correctly.

 

$ vlc stream.m3u 
VLC media player 2.1.4 Rincewind (revision 2.1.4-0-g2a072be)
[0xff5058] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
[0x1009808] main playlist: stopping playback
[0x7fbd70c055d8] ts demux error: MPEG-4 descriptor not found

 

 

 

EDIT: Ok, the problem is with the playlist file, if I take the URL and give it directly to VLC, it works ok.

 

I seem to remember that there was a similar issue before, where the .m3u file was not liked by VLC. Is that correct?

 

$ vlc http://vu2:8002/1:0:1:189D:7FD:2:11A0000:0:0:0:
VLC media player 2.1.4 Rincewind (revision 2.1.4-0-g2a072be)
[0xdfd058] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
[0x7fb4bcc04c38] ts demux error: MPEG-4 descriptor not found
[0x7fb4bce25c88] packetizer_mpeg4audio packetizer: AAC channels: 2 samplerate: 48000
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
[0x7fb4a4001248] main vout display error: Failed to resize display
[h264 @ 0x7fb4bcca7940] illegal short term buffer state detected
[0x7fb4d40063c8] freetype spu text error: Breaking unbreakable line
[h264 @ 0x7fb4bcca7940] Missing reference picture
[h264 @ 0x7fb4bcca8600] Reinit context to 720x480, pix_fmt: 0
[0x7fb4d40063c8] freetype spu text error: Breaking unbreakable line
[0x7fb4a4001248] main vout display error: Failed to resize display
[0x7fb4d40063c8] freetype spu text error: Breaking unbreakable line

 

 


Edited by Kers, 5 June 2014 - 15:46.


Re: Transcoding problem #620 Kers

  • Member
  • 43 posts

+2
Neutral

Posted 5 June 2014 - 15:50

For completeness sake, here is the playlist file contents:

$ more stream.m3u 
#EXTM3U 
#EXTVLCOPT--http-reconnect=true 
#EXTVLCOPT:program=6301
http://vu2:8002/1:0:1:189D:7FD:2:11A0000:0:0:0:

 




2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users