Hi at all, yesterday i installed a freshly openpli 4.0 on my solo2. Then i installed the driver for my dvb-t usb tuner a867 (kernel-module-dvb-usb-a867)
Here some telnet output
cat /proc/bus/nim_sockets
NIM Socket 0:
Type: DVB-S2
Name: BCM7356 DVB-S2 NIM (internal)
Frontend_Device: 0
NIM Socket 1:
Type: DVB-S2
Name: BCM7356 DVB-S2 NIM (internal)
Frontend_Device: 1
NIM Socket 2:
Type: DVB-T
Name: A867
Frontend_Device: 2
lsmod Module Size Used by ipv6 283728 28 dvb_usb_a867 200864 2 dvb_usb 15856 1 dvb_usb_a867 fpga_directc 416 0 brcmfb 1040 2 dvb_bcm7356 11841040 16 brcmfb procmk 1280 1 dvb_bcm7356
dmesg
Linux version 3.3.8-2.0 (build@buildserver) (gcc version 4.8.2 (GCC) ) #1 SMP Mon Jun 2 04:40:32 CEST 2014
Fetching vars from bootloader... found 16 vars.
Options: moca=0 sata=1 pcie=0 usb=1
Using 1024 MB + 0 MB RAM (from CFE)
CPU revision is: 00025a11 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 30000000 @ 20000000 (usable)
bmem: adding 57 MB LINUX region at 6 MB (0x039b1000@0x0064f000)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
bmem: adding 256 MB RESERVED region at 512 MB (0x10000000@0x20000000)
bmem: adding 512 MB LINUX region at 768 MB (0x20000000@0x30000000)
Zone PFN ranges:
Normal 0x00000000 -> 0x00050000
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00050000
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat 805f3a00, node_mem_map 81000000
Normal zone: 2560 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 259584 pages, LIFO batch:31
PERCPU: Embedded 7 pages/cpu @81a09000 s5632 r8192 d14848 u32768
pcpu-alloc: s5632 r8192 d14848 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259584
Kernel command line: ubiroot rootflags=sync bmem=192M@64M bmem=256M@512M ubi.mtd=rootfs rootfstype=ubifs root=ubi0:rootfs
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
Memory: 572236k/1048576k available (5210k kernel code, 476340k reserved, 950k data, 172k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:160
Measuring MIPS counter frequency...
Detected MIPS clock frequency: 1305 MHz (163.130 MHz counter)
Calibrating delay loop... 869.37 BogoMIPS (lpj=434688)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
bcm40nm_pm_moca_disable 00
SMP: Booting CPU1...
CPU revision is: 00025a11 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
SMP: CPU1 is running
Brought up 2 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
USB0: power enable is active high; overcurrent is active low
USB1: power enable is active high; overcurrent is active low
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource wktmr
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.18)
msgmni has been set to 1117
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10406900 (irq = 65) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10406940 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406980 (irq = 67) is a 16550A
loop: module loaded
__clk_enable: sata [1]
bcm40nm_pm_sata_enable 00
ahci: SSS flag set, parallel bus scan disabled
ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci strict-ahci.0: flags: ncq sntf stag clo slum part
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 41
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 41
brcmstb_nand: NAND controller driver is loaded
__clk_enable: network [1]
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
Found PHY at Address 3
Config GPHY through MDIO
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
__clk_enable: network [1]
__clk_enable: moca_genet [1]
bcm40nm_pm_genet1_enable 00
__clk_enable: moca [1]
bcm40nm_pm_moca_enable 00
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
No PHY detected, not registering interface:1
__clk_disable: moca [0]
bcm40nm_pm_moca_disable 00
__clk_disable: moca_genet [0]
bcm40nm_pm_genet1_disable 00
__clk_disable: network [0]
bcmgenet: probe of bcmgenet.1 failed with error -5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 69, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 70, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 74, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 75, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 71, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 72, io mem 0x10480600
usb 1-1: new high-speed USB device number 2 using ehci-brcm
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 76, io mem 0x10490400
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 77, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
scsi2 : usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 254
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
usb 2-1: new high-speed USB device number 2 using ehci-brcm
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR SANYO protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
Registering the dns_resolver key type
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS0: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, Hamming ECC
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002ec0000
nand_read_bbt: bad block at 0x000004f60000
nand_read_bbt: bad block at 0x000007380000
nand_read_bbt: bad block at 0x000008500000
Creating 4 MTD partitions on "brcmnand.0":
0x000001f00000-0x000010000000 : "rootfs"
0x000001f00000-0x000010000000 : "rootfs(redundant)"
0x000000200000-0x000000900000 : "kernel"
0x000000900000-0x000000a00000 : "mac"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
scsi 2:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: Attached scsi generic sg0 type 0
UBI: max. sequence number: 1249
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 225 MiB
UBI: number of good PEBs: 1792
UBI: number of bad PEBs: 8
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1792
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 149/83
UBI: image sequence number: 1804855202
UBI: background thread "ubi_bgt0d" started, PID 47
sd 2:0:0:0: [sda] 7905024 512-byte logical blocks: (4.04 GB/3.76 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sda] No Caching mode page present
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] No Caching mode page present
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 2:0:0:0: [sda] No Caching mode page present
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk
UBIFS: parse sync
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 223477760 bytes (218240 KiB, 213 MiB, 1760 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:13.
devtmpfs: mounted
Freeing unused kernel memory: 172k freed
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
procmk_init
dvb_bcm7356: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (vusolo2)
bcm7356: hotplug_callback():
Hotplug - status.connected 1:0
bcm7356: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
[GP]:brcm_pwm_init
brcm_demux_init: $Id: bcm_demux.c,v 0.7 $
[MPVR]: >> misc_pvr_init
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7346 FE)...
DVB: registering adapter 0 frontend 0 (BCM7346 FE)...
input: dreambox advanced remote control (native) as /devices/virtual/input/input0
[LCD]: registered
0:0
[CI]: registered ci0
[DFP]: registered dbox fp
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
BKNI_P_GetTrackAllocEntry_resize: resizing from 4096->8192
BKNI_Malloc(linuxkernel) top users:
blocks, bytes, filename:line
960, 204528, ../BSEAV/lib/utils/balloc.c:35
550, 22000, ../magnum/basemodules/mem/bmem_system.c:286
380, 45600, magnum/commonutils/mrc/7346/bmrc_monitor.c:940
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc5
fpga update driver loaded
AVerMedia A867 driver module V1.0.27 loaded.
dvb-usb: found a 'AVerMedia A867 DVB-T Recevier' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (AVerMedia A867 DVB-T Recevier)
DVB: registering adapter 1 frontend 0 (A867 USB DVB-T)...
dvb-usb: AVerMedia A867 DVB-T Recevier successfully initialized and connected.
usbcore: registered new interface driver dvb-usb-a867
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
__clk_enable: network [1]
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
eth0: Link up, 100 Mbps Full Duplex
NET: Registered protocol family 10
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[LCD]: unknown cmd 0x1015
[CI]: CI interface initialised
DVB: registering adapter 0 frontend 0 (vtuner fe)...
eth0: no IPv6 routers present
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -818577936
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER -818577936
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
FE tune
[AUD]: AUDIO_SELECT_SOURCE 0
[AUD]: AUDIO_SET_BYPASS_MODE 1
[AUD]: downmix 0 state : 0
[AUD]: AUDIO_PAUSE 6458528
[AUD]: AUDIO_PLAY 6458528 decoder start : 0
[VID]: VIDEO_SELECT_SOURCE 0
[VID]: VIDEO_GET_SIZE src w: 1280 h:720 display w:1280 h:720
[VID]: VIDEO_GET_SIZE aspect: 1 6
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_FREEZE 6458528 0
[VID]: VIDEO_PLAY 6458528 2 2
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 6458528 1
[AUD]: AUDIO_CONTINUE 6458528 1 aph=0xcf119100
[AUD]: setting mute : 0
[AUD]: AUDIO_CHANNEL_SELECT 0
The tuner is recognized but doesn't work properly: 5 channel founds instead of more than 300.
Could someone help me?
If a developer need hardware for tests (the stick, not the decoder 
) please send me a pm.
