Hallo, hopelijk kan iemand mij helpen met onderstaand probleem.
Op mijn dreambox gebruik ik al een tijdje een Tivii S660 USB tuner voor dvb-s. Hiervoor heb ik alleen de dw2102 driver hoeven installeren.
Nu wil ik de usb tuner graag in de VU+ Duo2 gebruiken. Hier heb ik ook de dw2102 driver geinstalleerd maar wat ik ook probeer de tuner de tuner raakt niet zichtbaar in PLI.
Is er iemand die weet wat ik hieraan kan doen of wat er mis gaat ?
=====
dmesg log
Duo2 LCD initialized 0
[LCD]: registered
[CI]: registered ci0 249
[CI]: registered ci1 248
[DFP]: registered dbox fp
[DFP]: Scart 9597 is found 0
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
FP Update Driver Loaded
VFDController Update Driver Loaded
fpga update driver loaded
dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-s660.fw'
dw2102: start downloading DW210X firmware
usb 2-1: USB disconnect, device number 2
dvb-usb: found a 'TeVii S660 USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TeVii S660 USB)
dvb-usb: MAC address: 01:01:01:01:01:01
DVB: Unable to find symbol ds3000_attach()
dvb-usb: no frontend was attached by 'TeVii S660 USB'
dvb-usb: TeVii S660 USB successfully initialized and connected.
usbcore: registered new interface driver dw2102
dvb-usb: TeVii S660 USB successfully deinitialized and disconnected.
usb 4-1: reset high-speed USB device number 2 using ehci-brcm
phy0 -> rt2800_init_eeprom: Error - Invalid RT chipset detected.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
usbcore: registered new interface driver rt2800usb
rtusb init rt2870 --->
=== pAd = f8203000, size = 511144 ===
usbcore: registered new interface driver rt2870
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
usb 2-1: new high-speed USB device number 3 using ehci-brcm
__clk_enable: network [1]
bcm7425_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
usb 2-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpac
ket 2
dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware
eth0: Link up, 1000 Mbps Full Duplex
dvb-usb: downloading firmware from file 'dvb-usb-s660.fw'
dw2102: start downloading DW210X firmware
dvb-usb: found a 'TeVii S660 USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TeVii S660 USB)
NET: Registered protocol family 10
dvb-usb: MAC address: 00:18:bd:5b:c6:52
DVB: Unable to find symbol ds3000_attach()
dvb-usb: no frontend was attached by 'TeVii S660 USB'
dvb-usb: TeVii S660 USB successfully initialized and connected.
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[CI]: CI interface initialised
eth0: no IPv6 routers present
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -823788048
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER -823788048
[AUD]: AUDIO_SET_MIXER : amixl 35, amixr 35
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER : next left volume -2570, right volume -2570
FE tune
[AUD]: AUDIO_SELECT_SOURCE 0
[AUD]: AUDIO_SET_BYPASS_MODE 1
[AUD]: downmix 0 state : 0
[AUD]: AUDIO_PAUSE 6482032
[AUD]: AUDIO_PLAY 6482032 decoder start : 0
[VID]: VIDEO_SELECT_SOURCE 0
[VID]: VIDEO_GET_SIZE src w: 1280 h:720 display w:1280 h:720
[VID]: VIDEO_GET_SIZE aspect: 1 6
[VID]: VIDEO_SET_STREAMTYPE 1
[VID]: VIDEO_FREEZE 6482032 0
[VID]: VIDEO_PLAY 6482032 5 2
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 6482032 1
[AUD]: AUDIO_CONTINUE 6482032 1 aph=0xcec2b680
[AUD]: setting mute : 0
[AUD]: AUDIO_CHANNEL_SELECT 0
