I have this problem posted earlier in the Dutch language section
Unfortunately there was no one who could help. Hopefully there is someone who can help here
On my dreambox I use an Tivii S660 USB DVB-S tuner for a while. To get this working, i only must install the Dw2102 driver.
Now i would like to use the usb tuner in the VU + Duo2. Here i have also installed the dw2102 driver. But the tuner is not working.
Does anyone know what I can do or what is going wrong?
=====
dmesg log
Duo2 LCD initialized 0
[LCD]: registered
[CI]: registered ci0 249
[CI]: registered ci1 248
[DFP]: registered dbox fp
[DFP]: Scart 9597 is found 0
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
FP Update Driver Loaded
VFDController Update Driver Loaded
fpga update driver loaded
dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-s660.fw'
dw2102: start downloading DW210X firmware
usb 2-1: USB disconnect, device number 2
dvb-usb: found a 'TeVii S660 USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TeVii S660 USB)
dvb-usb: MAC address: 01:01:01:01:01:01
DVB: Unable to find symbol ds3000_attach()
dvb-usb: no frontend was attached by 'TeVii S660 USB'
dvb-usb: TeVii S660 USB successfully initialized and connected.
usbcore: registered new interface driver dw2102
dvb-usb: TeVii S660 USB successfully deinitialized and disconnected.
usb 4-1: reset high-speed USB device number 2 using ehci-brcm
phy0 -> rt2800_init_eeprom: Error - Invalid RT chipset detected.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
usbcore: registered new interface driver rt2800usb
rtusb init rt2870 --->
=== pAd = f8203000, size = 511144 ===
usbcore: registered new interface driver rt2870
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
usb 2-1: new high-speed USB device number 3 using ehci-brcm
__clk_enable: network [1]
bcm7425_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
usb 2-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpac
ket 2
dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware
eth0: Link up, 1000 Mbps Full Duplex
dvb-usb: downloading firmware from file 'dvb-usb-s660.fw'
dw2102: start downloading DW210X firmware
dvb-usb: found a 'TeVii S660 USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (TeVii S660 USB)
NET: Registered protocol family 10
dvb-usb: MAC address: 00:18:bd:5b:c6:52
DVB: Unable to find symbol ds3000_attach()
dvb-usb: no frontend was attached by 'TeVii S660 USB'
dvb-usb: TeVii S660 USB successfully initialized and connected.
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[CI]: CI interface initialised
eth0: no IPv6 routers present
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -823788048
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER -823788048
[AUD]: AUDIO_SET_MIXER : amixl 35, amixr 35
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER : next left volume -2570, right volume -2570
FE tune
[AUD]: AUDIO_SELECT_SOURCE 0
[AUD]: AUDIO_SET_BYPASS_MODE 1
[AUD]: downmix 0 state : 0
[AUD]: AUDIO_PAUSE 6482032
[AUD]: AUDIO_PLAY 6482032 decoder start : 0
[VID]: VIDEO_SELECT_SOURCE 0
[VID]: VIDEO_GET_SIZE src w: 1280 h:720 display w:1280 h:720
[VID]: VIDEO_GET_SIZE aspect: 1 6
[VID]: VIDEO_SET_STREAMTYPE 1
[VID]: VIDEO_FREEZE 6482032 0
[VID]: VIDEO_PLAY 6482032 5 2
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 6482032 1
[AUD]: AUDIO_CONTINUE 6482032 1 aph=0xcec2b680
[AUD]: setting mute : 0
[AUD]: AUDIO_CHANNEL_SELECT 0
