Jump to content


Photo

2016/1/8 STB blijft hangen na huidige update


  • Please log in to reply
26 replies to this topic

#1 Jan Gruuthuse

  • Senior Member
  • 984 posts

+20
Neutral

Posted 8 January 2016 - 08:27

Duits subforum en Engels subforum  melden ook andere stb's die blijven hangen.

Ik kan telnetten, hij blijft precies in een lus hangen (blauw rondraaiend bolletje stopt en start tekens opnieuw)

dmesg
Linux version 3.12.1 (build@buildserver) (gcc version 4.9.1 (GCC) ) #1 Sun Feb 15 15:15:39 CET 2015
Fetching vars from bootloader... found 7 vars.
Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=0 moca=0
         sata=0 docsis=0 pci=0 pcie=0 smp=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
MEMC0 split: 256 MB -> Linux; 256 MB -> extra bmem
CPU revision is: 00029032 (Broadcom BMIPS3300)
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
bmem: adding 232 MB LINUX region at 7 MB (0x0e843000@0x007bd000)
bmem: adding 16 MB RESERVED region at 240 MB (0x01000000@0x0f000000)
Zone ranges:
  Normal   [mem 0x00000000-0x0fffffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x0fffffff]
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat 807701e0, node_mem_map 81000000
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 65536 pages, LIFO batch:15
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line:  ubi.mtd=rootfs rootfstype=ubifs root=ubi0:rootfs bmem=256M@512M bmem=16M console=null consoleblank=0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 235544K/262144K available (6108K kernel code, 289K rwdata, 1208K rodata, 188K init, 113K bss, 26600K reserved)
NR_IRQS:160
Measuring MIPS counter frequency...
Detected MIPS clock frequency: 501 MHz (250.508 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 497.66 BogoMIPS (lpj=248832)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
devtmpfs: initialized
bmem: adding extra 256 MB RESERVED region at 512 MB (0x10000000@0x20000000)
NET: Registered protocol family 16
USB0: power enable is active low; overcurrent is active low
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switched to clocksource wktmr
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
fuse init (API version 7.22)
msgmni has been set to 460
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62, base_baud = 5062500) is a 16550A
serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63, base_baud = 5062500) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64, base_baud = 5062500) is a 16550A
loop: module loaded
brcmstb_nand: NAND controller driver is loaded
__clk_enable: network [1]
__clk_enable: enet [1]
bcm7552_pm_genet_enable 00
Config internal EPHY through MDIO
__clk_disable: enet [0]
bcm7552_pm_genet_disable 00
__clk_disable: network [0]
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm7552_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver btusb
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Key type dns_resolver registered
EBI CS2: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-15

Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000008000000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000008000000 : "rootfs"
PM: CP0 COUNT/COMPARE frequency depends on divisor
UBI: attaching mtd2 to ubi0
usb 1-1: new high-speed USB device number 2 using ehci-brcm
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi0 : usb-storage 1-1:1.0
usb 1-2: new high-speed USB device number 3 using ehci-brcm
UBI: scanning is finished
UBI: attached mtd2 (name "rootfs", size 122 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 972, bad PEBs: 4, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 26/11, WL threshold: 4096, image sequence number: 473550298
UBI: available PEBs: 0, total reserved PEBs: 972, PEBs reserved for bad PEB handling: 16
ALSA device list:
  No soundcards found.
Warning: unable to open an initial console.
UBI: background thread "ubi_bgt0d" started, PID 43
scsi 0:0:0:0: Direct-Access     Imation  Nano Pro         PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 15859712 512-byte logical blocks: (8.12 GB/7.56 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
UBIFS: background thread "ubifs_bgt0_0" started, PID 46
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 119484416 bytes (113 MiB, 941 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2B181A08-CE08-42B8-A0F2-D3D7F2A69224, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:10.
devtmpfs: mounted
Freeing unused kernel memory: 188K (80771000 - 807a0000)
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
usbcore: registered new interface driver tpm
dvb: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
i2c-core: driver [ch455] using legacy suspend method
i2c-core: driver [ch455] using legacy resume method
Console: switching to colour frame buffer device 160x45
input: dreambox remote control (native) as /devices/virtual/input/input0
input: dreambox advanced remote control (native) as /devices/virtual/input/input1
DVB: registering new adapter (dvb0)
platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
input: front panel as /devices/virtual/input/input2
Console: switching to colour dummy device 80x25
__clk_enable: network [1]
__clk_enable: enet [1]
bcm7552_pm_genet_enable 00
eth0 Link DOWN.
NET: Registered protocol family 10
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0 Link UP.
Auto config phy
eth0: Link is up, 100 Mbps Full Duplex
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

nog iets anders nodig?


Edited by Jan Gruuthuse, 8 January 2016 - 08:30.

3 * xp1000 OpenPli 4.0 + usb 3.0 stick 64 GB, fixed lnb 28.2E, 23.5E ,19.2E ,16E, 13E, 9E, 4.8E, n4100pro 12 TB


Re: 2016/1/8 STB blijft hangen na huidige update #2 sneuper

  • Member
  • 6 posts

0
Neutral

Posted 8 January 2016 - 08:34

xtrend et10000 idem. blijft hangen na update vannacht.



Re: 2016/1/8 STB blijft hangen na huidige update #3 S_Hopper

  • Senior Member
  • 286 posts

+5
Neutral

Posted 8 January 2016 - 08:37

VU Ultimo idem

Re: 2016/1/8 STB blijft hangen na huidige update #4 Geuze

  • Senior Member
  • 692 posts

+7
Neutral

Posted 8 January 2016 - 08:38

Xtrend 10000 vanmorgen geupdate en deze blijft hangen.

Toen de update van 7 jan. er opgezet, de box werkt weer maar de afstandsbediening werkt niet meer.

Toen de update van 6 jan. er opgezet, de box werkt als vanouds.


Visiosat Big Satellite schotel met 4 quad, 7 twin LNB's voor Astra 1, 2, 3, Hotbird, 9 oost, 4.8 oost, 5 west, 31 oost, 42 oost, 0,8 west, 33 oost en een Triax schotel, 78 cm met single LNB voor Astra 3 beide aangesloten op VU+ Ultimo 4k met 2 sattuners en SSD en een Mutant HD 51 met 2 tuners waaronder 1 voor de Franse streams en SSD. De  1.40 Triax prime focus verwijderd wegens slijtage.


Re: 2016/1/8 STB blijft hangen na huidige update #5 Jan Gruuthuse

  • Senior Member
  • 984 posts

+20
Neutral

Posted 8 January 2016 - 08:44

/var/volatile/log/messages:

Jan  1 01:04:33 xp1000 authpriv.warn dropbear[1276]: lastlog_perform_login: Couldn't stat /var/log/lastlog: No such file or directory
Jan  1 01:04:33 xp1000 authpriv.warn dropbear[1276]: lastlog_openseek: /var/log/lastlog is not a file or directory!
Jan  1 01:04:46 xp1000 authpriv.info dropbear[1263]: Exit (root): Disconnect received

3 * xp1000 OpenPli 4.0 + usb 3.0 stick 64 GB, fixed lnb 28.2E, 23.5E ,19.2E ,16E, 13E, 9E, 4.8E, n4100pro 12 TB


Re: 2016/1/8 STB blijft hangen na huidige update #6 sneuper

  • Member
  • 6 posts

0
Neutral

Posted 8 January 2016 - 08:57

et10000 terugflashen naar oude versie....na reboot steeds blijven hangen in booten.... eerst nadat ook de bootloader geflasht werd en pli opnieuw geflasht werkt alles weer normaal.



Re: 2016/1/8 STB blijft hangen na huidige update #7 Tech

  • Forum Moderator
    PLi® Core member
  • 32,726 posts

+354
Excellent

Posted 8 January 2016 - 10:35

Is inmiddels bekend, de oplossing is er ook en de fix wordt snel ge-commit (hoop ik) ;)

 

 

Even niet updaten dus en het heeft niets met een bootloader te maken, die zit nooit in een (online)update, je hoeft dus geen onnodige zaken te doen ;)


Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....

Re: 2016/1/8 STB blijft hangen na huidige update #8 Tech

  • Forum Moderator
    PLi® Core member
  • 32,726 posts

+354
Excellent

Posted 8 January 2016 - 10:38

Xtrend 10000 vanmorgen geupdate en deze blijft hangen.

Toen de update van 7 jan. er opgezet, de box werkt weer maar de afstandsbediening werkt niet meer.

Toen de update van 6 jan. er opgezet, de box werkt als vanouds.

Klopt, in de image van de 7e zit een fout welke betrekking heeft tot de afstandsbediening, die van vandaag heeft een probleem met een display-aansturing, het veiligste is dus even twee dagen terug.


Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....

Re: 2016/1/8 STB blijft hangen na huidige update #9 littlesat

  • PLi® Core member
  • 53,190 posts

+614
Excellent

Posted 8 January 2016 - 11:25

Sorry want het is mijn foutje..... en dan ook nog op mijn verjaardag!

Alle boxen crashen, behalve de ET8500 en de Vu+Solo4K... Want alleen deze boxen hebben liveTVop het LCD...


WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: 2016/1/8 STB blijft hangen na huidige update #10 Pedro_Newbie

  • Senior Member
  • 4,631 posts

+225
Excellent

Posted 8 January 2016 - 11:45

Nou jij bent nog niet jarig... :(

 

O ja, jawel, van harte!



Re: 2016/1/8 STB blijft hangen na huidige update #11 Jan Gruuthuse

  • Senior Member
  • 984 posts

+20
Neutral

Posted 8 January 2016 - 11:45

Hihi, gelukkige verjaardag in elk geval. Kan iedereen overkomen: beide ;) Persoonlijk kijk ik liever op een ietwat groter scherm naar TV.


3 * xp1000 OpenPli 4.0 + usb 3.0 stick 64 GB, fixed lnb 28.2E, 23.5E ,19.2E ,16E, 13E, 9E, 4.8E, n4100pro 12 TB


Re: 2016/1/8 STB blijft hangen na huidige update #12 WanWizard

  • PLi® Core member
  • 58,455 posts

+1,276
Excellent

Posted 8 January 2016 - 12:40

Eerst fixen, dan taart eten!!! :P


Currently in use: VU+Duo 4K (2xFBC S2), Amiko Viper T2C (T2+fallback), Octagon SF8008 (S2+T2), Zgemma H9.2H (T2+fallback)

Many answers to your question can be found in our new and improved wiki.

Because to health reasons, I will not be active online very often anymore.


Re: 2016/1/8 STB blijft hangen na huidige update #13 Tech

  • Forum Moderator
    PLi® Core member
  • 32,726 posts

+354
Excellent

Posted 8 January 2016 - 12:41

Is intussen gefixed...hij mag aan de taart. :)
Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....

Re: 2016/1/8 STB blijft hangen na huidige update #14 littlesat

  • PLi® Core member
  • 53,190 posts

+614
Excellent

Posted 8 January 2016 - 13:35

Is de bouwserver dan ook al herstart....???


WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: 2016/1/8 STB blijft hangen na huidige update #15 Kosh

  • Senior Member
  • 429 posts

+5
Neutral

Posted 8 January 2016 - 14:09

Proficiat en een fijne dag. ;)


ET10K user i.c.w. Samsung UE40B6000 LED HDTV. ET9K alas not functioning anymore.


Re: 2016/1/8 STB blijft hangen na huidige update #16 Lutz

  • Senior Member
  • 712 posts

+1
Neutral

Posted 8 January 2016 - 18:52

Ook de ET9x00 heeft dit probleem. TErugflashen helpt.
<p>VU+Duo2, VU Solo SE, DM800HD se R.I.P, Visiosat Big Bisat schotel met QuadLnbs voor Astra 1 - 3, Hotbird

Re: 2016/1/8 STB blijft hangen na huidige update #17 Jan Gruuthuse

  • Senior Member
  • 984 posts

+20
Neutral

Posted 9 January 2016 - 09:08

bij XP1000 is dit terug in orde.


3 * xp1000 OpenPli 4.0 + usb 3.0 stick 64 GB, fixed lnb 28.2E, 23.5E ,19.2E ,16E, 13E, 9E, 4.8E, n4100pro 12 TB


Re: 2016/1/8 STB blijft hangen na huidige update #18 DeBeek

  • Senior Member
  • 1,469 posts

+46
Good

Posted 9 January 2016 - 09:11

DM8000  is weer Ok.


Vu+DUO4K, (DVB-C FBC & DVB-S2X FBC twin tuner), OpenPLi 8.0 Nightly Build, My-FullNightHD skin, Bluetooth remote,

2x Synology DS-116, 16 Gb USB3, Autotimer, Ziggo Kabel-tv, Astra 28.2.


Re: 2016/1/8 STB blijft hangen na huidige update #19 littlesat

  • PLi® Core member
  • 53,190 posts

+614
Excellent

Posted 9 January 2016 - 09:13

Bedankt voor de terugkoppeling.... Toch w88 we nog op het uitzetten van het stoplicht

WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: 2016/1/8 STB blijft hangen na huidige update #20 dolphs

  • Senior Member
  • 863 posts

+8
Neutral

Posted 9 January 2016 - 09:16

ET10000 ook zojuist bediend van een update en voorts met een " shutdown -r now ", all systems nominal !




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users