Ok, i'm ready for tests! Fresh image from today installed, then
opkg install enigma2-plugin-drivers-dvb-usb-af9035
Installing enigma2-plugin-drivers-dvb-usb-af9035 (1.0-r0.0) on root.
Downloading http://downloads.pli-images.org/feeds/openpli-4/mips32el/enigma2-plugin-drivers-dvb-usb-af9035_1.0-r0.0_mips32el.ipk.
Installing firmware-dvb-usb-af9035-02 (1.0-r0.15) on root.
Downloading http://downloads.pli-images.org/feeds/openpli-4/all/firmware-dvb-usb-af9035-02_1.0-r0.15_all.ipk.
Installing kernel-module-dvb-usb-af9035 (3.13.5-r2.4.4.5) on root.
Downloading http://downloads.pli-images.org/feeds/openpli-4/vusolo2/kernel-module-dvb-usb-af9035_3.13.5-r2.4.4.5_vusolo2.ipk.
Installing kernel-module-dvb-usb-v2 (3.13.5-r2.4.4.5) on root.
Downloading http://downloads.pli-images.org/feeds/openpli-4/vusolo2/kernel-module-dvb-usb-v2_3.13.5-r2.4.4.5_vusolo2.ipk.
Installing firmware-dvb-usb-it913x (1.0-r0.15) on root.
Downloading http://downloads.pli-images.org/feeds/openpli-4/all/firmware-dvb-usb-it913x_1.0-r0.15_all.ipk.
Configuring firmware-dvb-usb-af9035-02.
Configuring firmware-dvb-usb-it913x.
Configuring kernel-module-dvb-usb-v2.
Configuring kernel-module-dvb-usb-af9035.
lsusb
Bus 001 Device 002: ID 07ca:a867
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
uname -a
Linux vusolo2 3.13.5 #1 SMP Sat Dec 12 05:10:41 CET 2015 mips GNU/Linux
But after a restart tuner is not present
cat /proc/bus/nim_sockets
NIM Socket 0:
Type: DVB-S2
Name: BCM7356 DVB-S2 NIM (internal)
Frontend_Device: 0
NIM Socket 1:
Type: DVB-S2
Name: BCM7356 DVB-S2 NIM (internal)
Frontend_Device: 1
dmesg
fuse init (API version 7.22)
msgmni has been set to 1119
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10406900 (irq = 65, base_baud = 5062500) is a 16550A
console [ttyS0] enabled
bootconsole [early0] disabled
serial8250.0: ttyS1 at MMIO 0x10406940 (irq = 66, base_baud = 5062500) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406980 (irq = 67, base_baud = 5062500) is a 16550A
loop: module loaded
ahci strict-ahci.0: can't get clock
__clk_enable: sata [1]
bcm40nm_pm_sata_enable 00
ahci strict-ahci.0: SSS flag set, parallel bus scan disabled
ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci strict-ahci.0: flags: ncq sntf stag clo slum part
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 41
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 41
brcmstb_nand: NAND controller driver is loaded
__clk_enable: network [1]
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
Found PHY at Address 3
bcmgenet: configuring instance #0 for external RGMII
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ata1: SATA link down (SStatus 0 SControl 300)
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 69, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 70, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 74, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 75, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 71, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 72, io mem 0x10480600
ata2: SATA link down (SStatus 0 SControl 300)
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 76, io mem 0x10490400
usb 1-1: new high-speed USB device number 2 using ehci-brcm
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 77, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR SANYO protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS0: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
NAND device: 256MiB, SLC, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, Hamming ECC
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002ec0000
nand_read_bbt: bad block at 0x000004f60000
nand_read_bbt: bad block at 0x000007380000
nand_read_bbt: bad block at 0x000008500000
Creating 4 MTD partitions on "brcmnand.0":
0x000001f00000-0x000010000000 : "rootfs"
0x000001f00000-0x000010000000 : "rootfs(redundant)"
0x000000200000-0x000000900000 : "kernel"
0x000000900000-0x000000a00000 : "mac"
UBI: attaching mtd0 to ubi0
random: nonblocking pool is initialized
UBI: scanning is finished
UBI: attached mtd0 (name "rootfs", size 225 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 1792, bad PEBs: 8, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 208/126, WL threshold: 4096, image sequence number: 976308290
UBI: available PEBs: 0, total reserved PEBs: 1792, PEBs reserved for bad PEB handling: 32
UBI: background thread "ubi_bgt0d" started, PID 52
ALSA device list:
No soundcards found.
UBIFS: parse sync
UBIFS: background thread "ubifs_bgt0_0" started, PID 55
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 221573120 bytes (211 MiB, 1745 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID F2DD37FA-1909-4643-87F2-EE17C171DC80, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 208K (8073c000 - 80770000)
procmk_init
brcmnand brcmnand.0: corrected error at 0x25c9600
brcmnand brcmnand.0: corrected error at 0x25c9600
dvb_bcm7356: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (_vuplus_solo2_)
bcm7356: hotplug_callback():
Hotplug - status.connected 1:0:0
bcm7356: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
[GP]:brcm_pwm_init
brcm_demux_init: $Id: bcm_demux.c,v 0.7 $
[MPVR]: >> misc_pvr_init
[VID]: 6bcm7335_video_init
[AUD]: 6bcm7335_audio_init
BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (BCM7346 FE)...
BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (BCM7346 FE)...
BKNI_P_GetTrackAllocEntry_resize: resizing from 5376->8704
BKNI_Malloc(linuxkernel) top users:
blocks, bytes, filename:line
1024, 176128, portinginterface/hsm/src/common/bhsm.c:500
696, 158952, BSEAV/lib/utils/balloc.c:31
385, 24640, magnum/commonutils/mrc/src/bmrc_monitor.c:666
input: dreambox advanced remote control (native) as /devices/virtual/input/input0
[LCD]: registered
0:0
[CI]: registered ci0
[CI]: CI interface initialised
[DFP]: registered dbox fp
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
fpga update driver loaded
usb 1-1: dvb_usb_af9035: prechip_version=00 chip_version=03 chip_type=3802
usb 1-1: dvb_usb_v2: found a 'AVerMedia HD Volar (A867)' in cold state
usb 1-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-af9035-02.fw'
usb 1-1: dvb_usb_af9035: firmware version=12.13.15.0
usb 1-1: dvb_usb_v2: found a 'AVerMedia HD Volar (A867)' in warm state
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (AVerMedia HD Volar (A867))
DVB: Unable to find symbol af9033_attach()
usbcore: registered new interface driver dvb_usb_af9035
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1 0
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0 0
__clk_enable: network [1]
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0 eth0: link up, 1000 Mbps, full duplex
NET: Registered protocol family 10
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1 0
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0 0
[LCD]: unknown cmd 0x1015
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -840319504
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER -840319504
[AUD]: AUDIO_SET_MIXER : amixl 32, amixr 32
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER : next left volume -2355, right volume -2355
bcm7356: hotplug_callback():
Hotplug - status.connected 0:1:0
bcm7356: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7356: hotplug_callback():
Hotplug - status.connected 1:0:2
bcm7356: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
bcm7356: hotplug_callback():
Hotplug - status.connected 1:1:2
Probably i miss some packages...