Hi guys, sorry for the delay in replying and for my bad english.
I know that OpenPli does not support Zgemma STB, as well as many others, but is normally used (built) in any way.
In Zgemma H2H there is a MicroSD slot card reader (I meant this) that can be used in place a normal USB.
Well, after last update my 8GB microSD ext4 formatted it is no longer automatically mounted after boot even manually because there is no device.
root@ZG:/# mount
ubi0:rootfs on / type ubifs (rw,relatime)
devtmpfs on /dev type devtmpfs (rw,relatime,size=156504k,nr_inodes=39126,mode=755)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
tmpfs on /media type tmpfs (rw,relatime,size=64k)
tmpfs on /var/volatile type tmpfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
root@ZG:/# blkid
root@ZG:/#
nothing...
root@ZG:/# cat /etc/fstab
rootfs / auto defaults 1 1
proc /proc proc defaults 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
usbdevfs /proc/bus/usb usbdevfs auto 0 0
tmpfs /var/volatile tmpfs defaults 0 0
root@ZG:/# ls /dev
audio loop7 tty15 tty48
autofs mdev.seq tty16 tty49
bcm_au mem tty17 tty5
bus memory_bandwidth tty18 tty50
console misc tty19 tty51
cpu_dma_latency mixer tty2 tty52
dbox mtab tty20 tty53
dsp mtd tty21 tty54
dvb mtd0 tty22 tty55
fb mtd0ro tty23 tty56
fb0 mtd1 tty24 tty57
full mtd1ro tty25 tty58
fuse mtd2 tty26 tty59
hdmi_cec mtd2ro tty27 tty6
hwrng mtdblock tty28 tty60
i2c mtdblock0 tty29 tty61
i2c-0 mtdblock1 tty3 tty62
i2c-1 mtdblock2 tty30 tty63
i2c-2 network_latency tty31 tty7
i2c-3 network_throughput tty32 tty8
i2c-4 null tty33 tty9
i2c-5 ptmx tty34 ttyS0
i2c-6 pts tty35 ttyS1
initctl random tty36 ttyS2
input rfkill tty37 ttyS3
kmem sci0 tty38 ubi0
kmsg snapshot tty39 ubi0_0
log snd tty4 ubi_ctrl
loop-control tty tty40 urandom
loop0 tty0 tty41 vcs
loop1 tty1 tty42 vcs1
loop2 tty10 tty43 vcsa
loop3 tty11 tty44 vcsa1
loop4 tty12 tty45 videosnapshot0
loop5 tty13 tty46 zero
loop6 tty14 tty47
root@ZG:/# dmesg | grep -i usb
Options: moca=0 sata=1 pcie=0 usb=1
USB0: power enable is active low; overcurrent is active low
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm7552_pm_usb_enable 00
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 1-2: new high-speed USB device number 2 using ehci-brcm
hub 1-2:1.0: USB hub found
usb 1-2.4: new full-speed USB device number 3 using ehci-brcm
usbcore: registered new interface driver tpm
I'm sorry if I had not explained properly
Thank you anyway.
Edited by Blacksimon, 9 February 2016 - 22:21.