7 replies to this topic

[Tom77]

Hi,

 

I would like to use my USB DVB-S2 tuner Prof7500 with Vu+ Uno. 

 

http://www.linuxtv.o...DVB-S2_7500_USB

I downloaded firmware and put it into lib/firmware.

 

I also found topic http://forums.openpl...b-s2-prof-7500/

I copied procedure mentioned there, so I think the drivers are installed.

 

Tuner is connected to the usb on the back of Vu Uno, but I still can not see it in software. What else can I do?

[athoik]

Follow the instructions from the link you found above in openpli and post the output of dmesg and lsusb commands.

Also you might need to install the following as well.


kernel-module-dvb-usb-dw2102 - 4.3-r5 - dvb-usb-dw2102 kernel module dvb-usb-dw2102 kernel module; Driver for
DVBWorld DVB-S 2101, 2102, DVB-S2 2104, DVB-C 3101 USB2.0, TeVii S600,
S630, S650, S660, S480, S421, S632 Prof 1100, 7500 USB2.0, Geniatech

PS. Dont forget to place firmware in /lib

PPS. With prof 7500 you can do mis/pls

[Tom77]

Commands:

 

dmesg

Spoiler

pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]

pci 0000:01:00.0: [14e4:8602] type 00 class 0x01010f

PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)

pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]

pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]

pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01

pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]

pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]

cfg80211: Calling CRDA to update world regulatory domain

Switching to clocksource upg

FS-Cache: Loaded

NET: Registered protocol family 2

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP: reno registered

UDP hash table entries: 256 (order: 1, 8192 bytes)

UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

PCI: CLS 0 bytes, default 64

NFS: Registering the id_resolver key type

Key type id_resolver registered

Key type id_legacy registered

fuse init (API version 7.21)

msgmni has been set to 536

io scheduler noop registered

io scheduler cfq registered (default)

Serial: 8250/16550 dr

iver, 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A

console [ttyS0] enabled, bootconsole disabled

serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A

serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A

loop: module loaded

sata_brcmstb 0000:01:00.0: version 4.0

__clk_enable: sata [1]

PCI: Enabling device 0000:01:00.0 (0000 -> 0003)

sata_brcmstb 0000:01:00.0: setting latency timer to 64

scsi0 : sata_brcmstb

scsi1 : sata_brcmstb

ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42

ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42

Broadcom STB NAND controller (BrcmNand Controller)

bcmemac: Broadcom STB 10/100 EMAC driver v3.0

bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:03:17:9f)

bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)

usbcore: registered new interface driver zd1201

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

__clk_enable: usb [1]

ehci-brcm ehci-brcm.0: Broadcom STB EHCI

ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1

ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300

ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ehci-brcm ehci-brcm.1: Broadcom STB EHCI

ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2

ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500

ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-brcm ohci-brcm.0: Broadcom STB OHCI

ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3

ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

ohci-brcm ohci-brcm.1: Broadcom STB OHCI

ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4

ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 2 

ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

hidraw: raw HID events driver © Jiri Kosina

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP: cubic registered

NET: Registered protocol family 17

Key type dns_resolver registered

EBI CS0: setting up NAND flash (primary)

ata1: SATA link down (SStatus 4 SControl 300)

hub 1-0:1.0: unable to enumerate USB device on port 1

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000001

B4: NandSelect=40000101, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=ecf10095

After: NandSelect=40000101, nandConfig=15142200

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff

BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0

 

Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=ecf10095, tim1=4232222d, tim2=00000d94

BrcmNAND version = 0x0302 128MB @00000000

B4: NandSelect=40000101, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=ecf10095

After: NandSelect=40000101, nandConfig=15142200

Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0

brcmnand_scan: B4 nand_select = 40000101

brcmnand_scan: After nand_select = 40000101

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000

ECC layout=brcmnand_oob_bch4_4k

usb 1-2: new high-speed USB device number 3 using ehci-brcm

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsize=512, writesize=2048

brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0

Bad block table 1tb

B found at page 0000ff80, version 0x01 for chip on CS0

Creating 8 MTD partitions on "brcmnand.0":

0x000000000000-0x000007200000 : "rootfs"

0x000007200000-0x000007600000 : "kernel"

0x000007600000-0x000007a00000 : "boot"

0x000007a00000-0x000007c00000 : "splash"

0x000007c00000-0x000007d00000 : "cfe"

0x000007d00000-0x000007d80000 : "mac"

0x000007d80000-0x000007e00000 : "env"

0x000007e00000-0x000007f00000 : "nvm"

PM: CP0 COUNT/COMPARE frequency depends on divisor

UBI: attaching mtd0 to ubi0

usb 1-2: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2

ata2: SATA link down (SStatus 4 SControl 300)

UBI: scanning is finished

UBI: attached mtd0 (name "rootfs", size 114 MiB) to ubi0

UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

UBI: good PEBs: 912, bad PEBs: 0, corrupted PEBs: 0

UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

UBI: max/mean erase counter: 13/2, WL threshold: 4096, image sequence number: 831456370

UBI: available PEBs: 0, total reserved PEBs: 912, PEBs reserved for bad PEB handling: 20

ALSA device list:

UBI: background thread "ubi_bgt0d" started, PID 48

  No soundcards found.

UBIFS: parse sync

UBIFS: background thread "ubifs_bgt0_0" started, PID 49

UBIFS: recovery needed

UBIFS: recovery completed

UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)

UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

UBIFS: FS size: 111357952 bytes (106 MiB, 877 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

UBIFS: reserved for root: 0 bytes (0 KiB)

UBIFS: media format: w4/r0 (latest is w4/r0), UUID 06016B55-BE14-48AB-B45E-63C1712C43BF, small LPT model

VFS: Mounted root (ubifs filesystem) on device 0:10.

devtmpfs: mounted

Freeing unused kernel memory: 260k freed

procmk_init

dvb_bcm7413: module license 'Proprietary' taints kernel.

Disabling lock debugging due to k

ernel taint

DVB: registering new adapter (vuuno)

enable MII = 0

Booted !

NEXUS_Frontend_GetUserParameters 0 0 

bcm7413: hotplug_callback(): 

Hotplug - status.connected 1

bcm7413: hotplug_callback(): 

Hotplug - connecting HDMI to display 0xe

[GPIO]Default

[GPIO]RST Default

[GPIO]fpga secu

[GP]:brcm_pwm_init

 

brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $

[VID]: 6bcm7335_video_init

[AUD]: 6bcm7335_audio_init

BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (Vuplus FE)...

bcm7413: bcm7335_frontend_init(): vtuner1 : 2

[MPVR]: >> misc_pvr_init

input: dreambox advanced remote control (native) as /devices/virtual/input/input0

[LCD]: registered

[0;35m[CI]:[0;0m0 1

 

[CI]: registered ci0 0

[CI]: registered ci1 0

[DFP]: registered dbox fp

[DFP]: Scart 9597 is found 4

 

[SC]: registered sci0

[SC]: registered sci1

system_time_set wakeup mode get 

system_time_set wakeup mode get 0xc4

fpga update driver loaded

[VID]: VIDEO_SET_STREAMTYPE 0 

[VID]: VIDEO_SELECT_SOURCE 1  

[VID]: VIDEO_PLAY 1  2 0

[VID]: VIDEO_CONTINUE 1  1 

[VID]: VIDEO_CLEAR_BUFFER 1  1 0

[VID]: VIDEO_STOP 0  1

[VID]: VIDEO_SELECT_SOURCE 0  

NET: Registered protocol family 10

[VID]: VIDEO_SET_STREAMTYPE 0 

[VID]: VIDEO_SELECT_SOURCE 1  

[VID]: VIDEO_PLAY 1  2 0

[VID]: VIDEO_CONTINUE 1  1 

[VID]: VIDEO_CLEAR_BUFFER 1  1 0

[VID]: VIDEO_STOP 0  1

[VID]: VIDEO_SELECT_SOURCE 0  

[LCD]: unknown cmd 0x1015

[CI]:ci_dev_open

 

[CI]:entering.. A NEXUS_DvbCi_Open 

 

[CI]:NEXUS_DvbCi_Open done..

 

[CI]:Installing callbacks

 

[CI]:Forcing card check

 

[CI]:Card insertion status changed

 

[CI]:entering.. B NEXUS_DvbCi_Open 

 

[CI]:NEXUS_DvbCi_Open done..

 

[CI]:Installing callbacks

 

[CI]:Forcing card check

 

[CI]:Card B insertion status changed

 

[CI]: CI interface initialised

 

[CI]:ci1_dev_open

 

[SC]: !!!unknown cmd 0x5407

[AUD]: AUDIO_SET_MUTE 0 

[AUD]: AUDIO_SET_MIXER -817775120 

[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0

[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0

[AUD]: AUDIO_SE

T_MIXER : next left volume -70, right volume -70

[AUD]: AUDIO_SET_MIXER -817775120 

[AUD]: AUDIO_SET_MIXER : amixl 26, amixr 26

[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70

[AUD]: AUDIO_SET_MIXER : next left volume -1927, right volume -1927

FE tune

[AUD]: AUDIO_SELECT_SOURCE 0 

[AUD]: AUDIO_SET_BYPASS_MODE 0 

[AUD]: AC3 downmix 0  state : 0

[AUD]: AUDIO_PAUSE 4056 

[AUD]: AUDIO_PLAY 4056 decoder start : 0

[VID]: VIDEO_SELECT_SOURCE 0  

[VID]: VIDEO_GET_SIZE src w: 1280 h:720 display w:1280 h:720

[VID]: VIDEO_GET_SIZE aspect: 1 6

[VID]: VIDEO_SET_STREAMTYPE 1 

[VID]: VIDEO_FREEZE 4056  0

[VID]: VIDEO_PLAY 4056  5 2

[VID]: VIDEO_SLOWMOTION 0    1

[VID]: VIDEO_FAST_FORWARD 0    1

[VID]: VIDEO_CONTINUE 4056  1 

[AUD]: AUDIO_CONTINUE 4056 1 aph=0xe0c86a74

[AUD]: Mute : 0

[AUD]: AUDIO_CHANNEL_SELECT 0 

[VID]: VIDEO_SLOWMOTION 0    1

[VID]: VIDEO_FAST_FORWARD 0    1

[VID]: VIDEO_CONTINUE 4056  1 

[AUD]: AUDIO_CONTINUE 4056 1 aph=0xe0c86a74

[AUD]: Mute : 0

root@vuuno:~# [6n

 

lsusb

Spoiler

Bus 001 Device 003: ID 3034:7500

Bus 001 Device 001: ID 1d6b:0002

Bus 002 Device 001: ID 1d6b:0002

Bus 003 Device 001: ID 1d6b:0001

Bus 004 Device 001: ID 1d6b:0001

root@vuuno:~# [6n

Edited by Tom77, 8 March 2016 - 14:19.

[Tom77]

I run commands before installing last module. Installing kernel-module-dvb-usb-dw2102 helped. Now I can see second tuner.

 

Thank you athoik!

[MCelliotG]

So if you can receive mediaset on 5W give us a report!

[athoik]

So if you can receive mediaset on 5W give us a report!

 

He has to use experimental SatDreamGr image that includes patches for PLS/MIS on Enigma2 and on kernel for vuuno.

Edited by athoik, 8 March 2016 - 15:37.

[athoik]

I run commands before installing last module. Installing kernel-module-dvb-usb-dw2102 helped. Now I can see second tuner.

 

Thank you athoik!

 

Thanks for confirming that it works. I will add the depends in enigma2 dvb drivers, so users will just download the driver from Enigma2 drivers menu

Edited by athoik, 8 March 2016 - 15:36.

[athoik]

@Tom77,

Could you please tell us how this tuner is reported into Enigma2?


Please provide the following output if possible.

cat /proc/bus/nim_sockets