Posted 24 May 2016 - 21:23
So i got a green screen saying there is a problem with the STB after I tried to play a recording file, then tried to delete it.
Now I am stuck at the splash screen - is there a way to recover the image from here? Its currently installed on the Wetek on a SD card
Took to long to get everything working really don't want to start from scratch again, everything was working fine except playback of recordings which is when the error occurred.
Posted 24 May 2016 - 21:29
If you have a green screen, you have an error message. If you can't get to it, mayby take a phone of it? And post it here so we can have a look.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 24 May 2016 - 21:44
Posted 25 May 2016 - 00:01
Ok finally back up and running. I had to readd both my tuners, rescan and then manually enter my DNS for some reason was not being picked up.
One final problem, I cannot playback recorded files at all.. I just get a black screen. If i remove the HDD and connect it to my laptop I can view the files, so it seems to the player itself
I have been unable to fix this over the last couple of month now.
Can anyone help with this?
Posted 25 May 2016 - 01:58
Just to add a bit more detail on above, I setup a network share and set up a recording, it recorded fine and can be played back on my laptop but still receive a black screen from the PVR playback screen.
Would really like to get this fixed have spent hours on troubleshooting already,
At first i thought my HDD and format of the drive might be causing the issue but this isnt the case as it happens on a network share too.
This seems to be a problem with movie player on the software
Posted 25 May 2016 - 12:25
Can a dev check if playback of recorded files is broken on the Wetek please? I believe it is.
A couple of months ago the media player would play the files but could not fast forward, not its gone completely
Posted 25 May 2016 - 13:33
What do you mean by "media player"? You normally would play your recordings directly from the file list, recordings are processed directly by the hardware. Afaik the media player uses gstreamer.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 25 May 2016 - 14:03
Yea thats what I mean, So when I click PVR, select my file that I have just recorded. The player 'bar' pops up at the top of the screen and then I get a black screen and nothing plays..
So basically I cannot playback ANY recorded files
Posted 25 May 2016 - 15:15
Hmm... Then we'll have to wait until someone with a Wetek shows up, I don't have one.
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 25 May 2016 - 15:26
best thiung is to get some logging. Loggin to your wetek and run 'init 2'. then start enigma2 manualy (and maybe set debug level to 4 first). Without logging there is nothing much to say...
Posted 25 May 2016 - 17:00
best thiung is to get some logging. Loggin to your wetek and run 'init 2'. then start enigma2 manualy (and maybe set debug level to 4 first). Without logging there is nothing much to say...
My experience is very limited Engima2 I am not sure how to do this.
I logged into the box via telnet logged in as root. Typed init 2 and it crashed it box
Posted 25 May 2016 - 17:16
what do you mean by 'crash'?
your tv screen will go black that is ok.
But do you get a prompt back?
If so type: export ENIGMA_DEBUG_LVL=4
and the type: enigma2
now your tv screen should show useful things again and your telnet session should scroll with lots of informational messages.
The try your recording again. After your 'crash' , capture the telnet log (assuming you have a big scrollbakc buffer to retrieve the data that is already off the screen...)
and post this log
Posted 26 May 2016 - 19:48
Hi,
I think that it is init 3 (and not 2) so in telnet:
init 3 export ENIGMA_DEBUG_LVL=4 enigma2
To stop it CTRL-C and then to return to normal mode: init 4
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Posted 27 May 2016 - 09:37
0 members, 2 guests, 0 anonymous users
