13 replies to this topic

[mymon]

Has anyone successfully installed the it913x driver on the Zgemma H.2S

here is what I get:

 

 

usb 1-2.2: new high-speed USB device number 6 using ehci-brcm

input: ITE Technologies, Inc. USB Deivce as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.2/1-2.2:1.1/0003:048D:9006.0003/input/input5

hid-generic 0003:048D:9006.0003: input,hidraw0: USB HID v1.01 Keyboard [ITE Technologies, Inc. USB Deivce] on usb-ehci_hcd-2.2/input1

 

 

root@h3:~# opkg install enigma2-plugin-drivers-dvb-usb-it913x

Installing enigma2-plugin-drivers-dvb-usb-it913x (1.0-r0) on root.

Downloading enigma2-plugin-drivers-dvb-usb-it913x_1.0-r0_mips32el.ipk

Collected errors:

 * satisfy_dependencies_for: Cannot satisfy the following dependencies for enigma2-plugin-drivers-dvb-usb-it913x:

 *      kernel-module-dvb-usb-it913x * 

 * opkg_install_cmd: Cannot install package enigma2-plugin-drivers-dvb-usb-it913x.

 

Edited by mymon, 9 August 2016 - 15:46.

[athoik]

Try enigma2-plugin-drivers-dvb-usb-af9035

[mymon]

installation went fine

 

looks like the tuner is ready to go 

 

usb 1-2.2: new high-speed USB device number 4 using ehci-brcm

input: ITE Technologies, Inc. USB Deivce as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.2/1-2.2:1.1/0003:048D:9006.0001/input/input3

hid-generic 0003:048D:9006.0001: input,hidraw0: USB HID v1.01 Keyboard [ITE Technologies, Inc. USB Deivce] on usb-ehci_hcd-2.2/input1

usb 1-2.2: dvb_usb_af9035: prechip_version=83 chip_version=02 chip_type=9135

usb 1-2.2: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in cold state

usb 1-2.2: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9135-02.fw'

usb 1-2.2: dvb_usb_af9035: firmware version=3.39.1.0

usb 1-2.2: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in warm state

usb 1-2.2: dvb_usb_af9035: [0] overriding tuner from 00 to 60

usb 1-2.2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer

DVB: registering new adapter (ITE 9135(9006) Generic)

af9033 7-0038: firmware version: LINK 3.39.1.0 - OFDM 3.9.1.0

af9033 7-0038: Afatech AF9033 successfully attached

usb 1-2.2: DVB: registering adapter 1 frontend 0 (Afatech AF9033 (DVB-T))...

it913x 7-001c: ITE IT913X BX successfully attached

Registered IR keymap rc-it913x-v1

input: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.2/rc/rc0/input4

rc0: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-2/1-2.2/rc/rc0

usb 1-2.2: dvb_usb_v2: 'ITE 9135(9006) Generic' successfully initialized and connected

usbcore: registered new interface driver dvb_usb_af9035

 

but its not displayed under tuner configuration (just A and

[WanWizard]

You might need to restart Enigma (or even the box), I'm pretty sure Enigma itself isn't plug-and-play.

[mymon]

Ive rebooted it many times already.. I wouldn't waste your time otherwise.. Ive tried the OpenATV as well.. just don't know what's wrong with it.. its the Evolveo Mars USB donge

 

usb 1-1: new high-speed USB device number 5 using ehci-brcm

usb 1-1: dvb_usb_af9035: prechip_version=83 chip_version=02 chip_type=9135

usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in cold state

usb 1-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9135-02.fw'

usb 1-1: dvb_usb_af9035: firmware version=3.39.1.0

usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in warm state

usb 1-1: dvb_usb_af9035: [0] overriding tuner from 00 to 60

usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer

DVB: registering new adapter (ITE 9135(9006) Generic)

af9033 7-0038: firmware version: LINK 3.39.1.0 - OFDM 3.9.1.0

af9033 7-0038: Afatech AF9033 successfully attached

usb 1-1: DVB: registering adapter 1 frontend 0 (Afatech AF9033 (DVB-T))...

it913x 7-001c: ITE IT913X BX successfully attached

Registered IR keymap rc-it913x-v1

input: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input4

rc0: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0

usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' successfully initialized and connected

input: ITE Technologies, Inc. USB Deivce as /devices/platform/ehci-brcm.0/usb1/1-1/1-1:1.1/0003:048D:9006.0002/input/input5

hid-generic 0003:048D:9006.0002: input,hidraw0: USB HID v1.01 Keyboard [ITE Technologies, Inc. USB Deivce] on usb-ehci_hcd-1/input1

 

 

I'll give it a try on the Solo2 later on

Edited by mymon, 9 August 2016 - 17:15.

[mymon]

damnit.. sorry guys.. It turned out that it was recognised as a remote/keyboard.. as soon as I removed the battery from the remote (that came with it) and rebooted the box it showed up as tuner C

I hope I saved someone a lot of time (it took me few hours already.. trying different firmwares and images..)

[WanWizard]

lol, these things happen.

[ColinB]

damnit.. sorry guys.. It turned out that it was recognised as a remote/keyboard.. as soon as I removed the battery from the remote (that came with it) and rebooted the box it showed up as tuner C

I hope I saved someone a lot of time (it took me few hours already.. trying different firmwares and images..)

 

This is One for the Books.

 

Thank You

[mymon]

ehh.. not an easy one.. It works fine on the front USB but once its plugged on the back its no longer visible as tuner (I can see it in the log just fine)

I thought that maybe the Zgemma doesn't have enough power on the back (Amp) so I used active USB Hub.. still no joy

it makes absolutely no sense.. beside the voltage/Amp is there any other difference between the front and back USB port? - any advices?

[mymon]

Im still batteling with it.. what I managed to get is

 

1) Zgemma powers ON with tunner attached on the back.. its not visible

2) unplug the tunner.. plug it back in (into the back USB).. than in the log it shows

 

 

usb 1-1: USB disconnect, device number 2

usb 1-1: new high-speed USB device number 5 using ehci-brcm

usb 1-1: dvb_usb_af9035: prechip_version=83 chip_version=02 chip_type=9135

usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in cold state

usb 1-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9135-02.fw'

usb 1-1: dvb_usb_af9035: firmware version=3.39.1.0

usb 1-1: dvb_usb_v2: found a 'ITE 9135(9006) Generic' in warm state

usb 1-1: dvb_usb_af9035: [0] overriding tuner from 00 to 60

usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer

DVB: registering new adapter (ITE 9135(9006) Generic)

af9033 7-0038: firmware version: LINK 3.39.1.0 - OFDM 3.9.1.0

af9033 7-0038: Afatech AF9033 successfully attached

usb 1-1: DVB: registering adapter 1 frontend 0 (Afatech AF9033 (DVB-T))...

it913x 7-001c: ITE IT913X BX successfully attached

Registered IR keymap rc-it913x-v1

input: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0/input4

rc0: ITE 9135(9006) Generic as /devices/platform/ehci-brcm.0/usb1/1-1/rc/rc0

usb 1-1: dvb_usb_v2: 'ITE 9135(9006) Generic' successfully initialized and connected

input: ITE Technologies, Inc. USB Deivce as /devices/platform/ehci-brcm.0/usb1/1-1/1-1:1.1/0003:048D:9006.0002/input/input5

hid-generic 0003:048D:9006.0002: input,hidraw0: USB HID v1.01 Keyboard [ITE Technologies, Inc. USB Deivce] on usb-ehci_hcd-1/input1

 

3) restart enigma and tuner C is back

4) reboot the box and tuner C is gone again (I have to start the whole unplug/plug back in again)

 

 

If I attach the tuner into the front USB its visible all the time (no need for messing with unplug/plug and rebooting enigma)

[micktol]

You can try this,

 

 

edit root/usr/bin/ enigma2.sh add the lines like this at the start

 

#!/bin/sh

modprobe -r dvb-usb-af9035 &
sleep 5
modprobe  dvb-usb-af9035 &

prefix=/usr
exec_prefix=/usr
datarootdir=${prefix}/share

 

it restarts the driver, but you need to add it every time you do a system update as the file gets updated

Edited by micktol, 16 August 2016 - 19:05.

[mymon]

thats a good workaround.. If that works i could add into oscam starting script - I left the box at work.. will give it a try tomorrow

thanks!

[mymon]

update

its working! 

I wonder if there is any way to solve it for good?

[Adav642]

Hi all this is new to me but I have a Zygemma got kodidirect but keep getting Chinese subtitles yet when I go into subtitles it says non so how do I stop this happening.
Please keep it simple as I am a novice lol .