16 replies to this topic

[dundeept]

This weekend I had a problem with the energy supply (the energy power supplier cut the energy due to bad weather conditions) and my receiver (ET6000) was not powered for a while.

When the energy came the receiver was not booting, only appears the boot screen (and the leds red and green are always on). I can a access the receiver with telnet and the errors are (Crash Log in attachment) :

 

[fb] /dev/fb0 No such file or directory
<    343.831256> [fb] framebuffer not available
<    343.831317> FATAL: [gFBDC] no framebuffer available


I try install the bootloader and a new firmware again and again and the receiver accepts them but is always having the enigma2 crash.

What can I do?

Thanks in advance!
 

Attached Files

•  enigma2_crash_OpenPli.log   6.55KB   4 downloads

[WanWizard]

framebuffer not available means the drivers don't load.

 

If this keeps popping up, type the command "lsusb", and check the output for "dead:beef". If it is not present, the security board of your box has bought it. Only your supplier can replace it, not even sure if they are still available.

[dundeept]

framebuffer not available means the drivers don't load.

 

If this keeps popping up, type the command "lsusb", and check the output for "dead:beef". If it is not present, the security board of your box has bought it. Only your supplier can replace it, not even sure if they are still available.

 

First of all thanks!

 

To a "lsub" comand my ET6000 responds like this:

Bus 002 Device 002: ID 1a40:0101

Bus 001 Device 001: ID 1d6b:0002

Bus 002 Device 001: ID 1d6b:0002

Bus 003 Device 001: ID 1d6b:0001

Bus 004 Device 001: ID 1d6b:0001

 

I have also a ET5000 that responds with the "dead:beef":

Bus 001 Device 002: ID 1307:0165

Bus 002 Device 002: ID 1a40:0101

Bus 001 Device 001: ID 1d6b:0002

Bus 002 Device 001: ID 1d6b:0002

Bus 003 Device 001: ID 1d6b:0001

Bus 004 Device 001: ID 1d6b:0001

Bus 002 Device 003: ID dead:beef

 

So I have a problem with the security board.

 

Can I copy some files from the ET5000 to the ET6000 to make it ok?

 

And now I leave the ET6000 power off for a couple of days and when I turn it on it was hard for the receiver to start (10 minutes for the leds red and green start with a lot of powering off and on for the receiver starts). All the leds (green, red and yellow) were on but faded.

Edited by dundeept, 2 March 2017 - 00:53.

[betacentauri]

No, the security board is a piece of hardware in your receiver. You need to exchange it. No way to fix it by yourself.

[blzr]

From what I read here on the forum xtrend reportedly said once, that they'll provide drivers that circumvent the security board for their boxes, 'when the time comes',
https://forums.openp...ndpost&p=490484
Now, the 1-st generation xtrends are out of sales / production for a long time, and nothing happened (and I bet that there is no longer a chance for that).
'a bit' disappointing...

[Frenske]

@Blzr,

I agree. But as there is a new party for Xtrend there is some light at the end of this tunnel.

[kalehrl]

Hope the party gets started before my Xtrend leaves the house.

[dundeept]

First of all thank to all for the help!

 

I'm very disappointed with Xtrend. At the time the ET5000 and ET6000 xtrend came out I bought several and I recommended the purchase to other users.

And now a power failure is enough to have a receiver inoperable.

 

And they do not give a solution!

Since they no longer produce the ET6000, why do not they provide a solution to the security board problem?

[WanWizard]

the original Xtrend organisation is no more, there is a new party that is in the proces of  taking over, as Frenske already mentioned. Once that is finished, we can see if we can start a dialog with this party about this issue.

[dundeept]

the original Xtrend organisation is no more, there is a new party that is in the proces of  taking over, as Frenske already mentioned. Once that is finished, we can see if we can start a dialog with this party about this issue.

 

Ok!

Thanks!

[dundeept]

Any News? Or Solution?

 

Thanks in advance!

[Frenske]

I'll send them a message and inquire whether they can make a deal with the external partner to obtain some securityboards. Keep your fingers crossed.

[dundeept]

I'll send them a message and inquire whether they can make a deal with the external partner to obtain some securityboards. Keep your fingers crossed.

 

Many thanks!

[dundeept]

Any news about the security board problem?

 

Thanks in advance!

[Frenske]

Nope. You’d best mail directly to Elicom in Germany and ask them for a new SB. Although my contact is supposed being a coworker of Elicom this line is almost ‘dead’.

[dundeept]

Nope. You’d best mail directly to Elicom in Germany and ask them for a new SB. Although my contact is supposed being a coworker of Elicom this line is almost ‘dead’.

 

As you sugested I contact Elicom and I am waiting for a reply. 

 

Many Thanks! 

[kalehrl]

My et6000 seems to have just bitten the dust:

root@et6x00:~# lsusb

Bus 001 Device 002: ID 2013:024f
Bus 001 Device 003: ID 125f:cb40
Bus 002 Device 002: ID 1a40:0101
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001