Posted 20 December 2017 - 11:12
Attached a file for restoring the factory splash screen for several brands/models.
Just extract the file to an USB stick and flash as you would flash an image. The actual image & data will not be overwritten.
If more boxes/brands can be supported please let me know (and please including a link to the factory image).
Restore_Splash_VU_Xtrend_Mutant_GoldenInterstar_Miraclebox.zip 2.24MB
138 downloads
Posted 20 December 2017 - 15:50
Unfortunately, it does not work for ET9000.
Perhaps the bootloader does not allow to replace splash screen although it must have allowed it in the past because it is years since I have been struggling with removing the RuDream logo the previous owner of my box used.
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 20 December 2017 - 17:01
For the ET9x-series the flashing of the splashbin must be allowed via an other button then flashing the image. Unfortunately I don't remember which button, and my 9x landed on the attic.
But I do remember it does work 
If you're lucky BetaCentauri will read this: he gave me the working tip at the time.
Posted 20 December 2017 - 17:42
Thanks, I'll wait.
By the way, the folder in your file is et9x00 while my display says ET9X00 on boot. Do I have to use capital letters or not?
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 20 December 2017 - 17:51
1- For the button allowing the flash: IIRC it's the opponent of the normal button. So if the normal button is "UP", the button allowing the screen flash is "DOWN" (or LEFT/Right).
2- The files in the folder should be correct (same as image folders).
Posted 20 December 2017 - 18:58
which is lower case. 
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 20 December 2017 - 20:17
1- For the button allowing the flash: IIRC it's the opponent of the normal button. So if the normal button is "UP", the button allowing the screen flash is "DOWN" (or LEFT/Right).
But for ET9000 the normal button is OK so what would the opposite be?
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 21 December 2017 - 07:00
Aan de rand van de afgrond is een stap voorwaarts niet altijd vooruitgang....
On the edge of the abyss, a step forward is not always progress....
Hardware: 2x Daily used Vu+ Ultimo 4K - Vu+ Duo 4K SE and a lot more.... - VisioSat BiBigsat - Jultec Unicable Multiswitch 4 positions: 19.2/23.5/28.2 East - Diseqc motorized flatdish antenna
Software : HomeBuild OpenPLi Develop and Scarthgap builds, local cards driven by OsCam
Press the 
button on the buttom right of this message
Have you tried our wiki yet? Many answers can be found in our OpenPLi wiki
Posted 21 December 2017 - 11:07
Once that has been confirmed I'll add it to the notes inside the folder.
Posted 21 December 2017 - 13:29
Posted 21 December 2017 - 14:17
I've asked the wiki editors to add these to the wiki, with instructions, so nobody has to start looking again...
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 21 December 2017 - 16:34
Thanks for confirming.
Instructions for Xtrend embedded and some more boxes added in attached file:
Restore_Splash_VU_Xtrend_Mutant_GigaBlue_GoldenInterstar_Miraclebox_GigaBlue.zip 6.08MB
53 downloads
Posted 21 December 2017 - 16:55
Once that has been confirmed I'll add it to the notes inside the folder.
Unfortunately this does not work for me.
When I switch the box on (using the back switch) and the stick contains a new image, I get a question on the display in order to confirm flashing and I press OK.
Here, there is nothing in the display and the box just goes on booting.
Or do I have to keep the UP button pressed at the same time as I switch the box on?
And by the way, should it be CHANNEL UP or VOLUME UP?
Edited by Robinson, 21 December 2017 - 16:56.
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 21 December 2017 - 17:21
Why don't just try them all? When I had an xtrend, I did Couldn't remember which.
* Wavefrontier T90 with 28E/23E/19E/13E via SCR switches 2 x 2 x 6 user bands
I don't read PM -> if you have something to ask or to report, do it in the forum so others can benefit. I don't take freelance jobs.
Ik lees geen PM -> als je iets te vragen of te melden hebt, doe het op het forum, zodat anderen er ook wat aan hebben.
Posted 21 December 2017 - 18:04
Posted 21 December 2017 - 18:05
Afaik there are only 4 buttons to test, like on the 10K?
Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)
Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.
Many answers to your question can be found in our new and improved wiki.
Posted 21 December 2017 - 20:13
OK, I give up for now. Tried various buttons, using a FAT32-formatted USB stick at the front, without success on my ET9000.
First of all, there is no prompt on the display, while there is one when a real image is on the USB stick. We don't know when to press a button. So I tried pressing it right after switching the box on as well as right before (still keeping it pressed down after switching the box on). I tried various UP, DOWN and MENU keys. All in vain.
I know there are probably just a handful of guys still owning ET9000 so there is noone who can prove me wrong.
When I get hold of another stick I may test more, perhaps using the port at the back.
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 21 December 2017 - 23:08
Posted 21 December 2017 - 23:27
Yes, exactly as in the zip from the first post by Rob.
folder et9x00 and noforce and splash.bin inside. No image file.
By the way, as regards image flashing, is it possible to have other personal folders on the USB stick or only the et9x00 is allowed? My question is not related to this situation because I did not have other folders or files on the stick.
ET9000, OpenPLi 4.0, 13E, 19E
HD51, OpenPLi 6.2, 75E - 30W
Posted 22 December 2017 - 06:45
By the way, as regards image flashing, is it possible to have other personal folders on the USB stick or only the et9x00 is allowed? My question is not related to this situation because I did not have other folders or files on the stick.
Yes, normally that should not be a problem. The only real problems one can encounter are:
1- Stick is too large (size does matter: the smaller the better (in this case))
2- Not properly formatted. When using the HP-tool it should always be fine. Formatting by Windows sometimes provides a stick not recognised by the box.
HPUSBFW_v2.2.3.zip 39.49KB
22 downloads
0 members, 7 guests, 0 anonymous users
