2740 replies to this topic

[sauna]

you can see why this error.this is a piece of log.

 

ERROR: Task (/home/aa/Desktop/kiplus/openpli-oe-core/openembedded-core/meta/recipes-core/dbus/dbus_1.10.14.bb:do_package_write_ipk) failed with exit code '1'

ERROR: openssl-1.0.2k-r0 do_package_write_ipk: Function failed: do_package_ipk

ERROR: Logfile of failure stored in: /home/aa/Desktop/kiplus/openpli-oe-core/build/tmp/work/aarch64-oe-linux/openssl/1.0.2k-r0/temp/log.do_package_write_ipk.16764

 

ERROR: Task (/home/aa/Desktop/kiplus/openpli-oe-core/openembedded-core/meta/recipes-connectivity/openssl/openssl_1.0.2k.bb:do_package_write_ipk) failed with exit code '1'

NOTE: Tasks Summary: Attempted 1986 tasks of which 1980 didn't need to be rerun and 2 failed.

 

Summary: 2 tasks failed:

  /home/aa/Desktop/kiplus/openpli-oe-core/openembedded-core/meta/recipes-core/dbus/dbus_1.10.14.bb:do_package_write_ipk

  /home/aa/Desktop/kiplus/openpli-oe-core/openembedded-core/meta/recipes-connectivity/openssl/openssl_1.0.2k.bb:do_package_write_ipk

Summary: There was 1 WARNING message shown.

Summary: There were 2 ERROR messages shown, returning a non-zero exit code.

Makefile:125: recipe for target 'image' failed

make: *** [image] Error 1

aa@aa-N81Vp:~/Desktop/kiplus/openpli-oe-core$ 

[Persian Prince]

New test images for mecool devices.

 

k1pro: http://www.mediafire...sdcard.zip/file

 

k2pro: http://www.mediafire...sdcard.zip/file

 

k2prov2: http://www.mediafire...sdcard.zip/file

 

k3pro: http://www.mediafire...sdcard.zip/file

 

k1plus: http://www.mediafire...sdcard.zip/file

[moham96]

 

 

 

New test images for mecool devices

k1pro: http://www.mediafire...sdcard.zip/file

k2pro: http://www.mediafire...sdcard.zip/file

k2prov2: http://www.mediafire...sdcard.zip/file

k3pro: http://www.mediafire...sdcard.zip/file

k1plus: http://www.mediafire...sdcard.zip/file

I've tested k1plus image dear Persian Rrince.
-Boot is not normal for me, still same.boots or not boots and stays on black screen.
-When boot is normal,restarting the box and it goes to "no signal" on tv screen and no booting.
-There is no Wlan settings.
-Remote is OK.
-Network is OK.and webif is OK.

After a little digging it seems like the k1plus uses rtl8189etv for wifi, so we probably need to add the r8189 module and firmware again

Yes I think so,dear moham96.

Thanks

 

there are multiple rtl modules in the coreelec image and I don't know which one k1plus uses, can you boot a Coreelec/Libreelec image and give the output of

lsmod | paste

and

dmesg | paste

[moham96]

[    2.675397@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.685579@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    2.793438@2] dwc_otg: Core Release: 3.10a
[    2.793473@2] dwc_otg: Setting default values for core params
[    2.797643@2] dwc_otg: curmode: 0, host_only: 0
[    2.813535@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.813535@2] 
[    2.830880@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.830880@2] 
[    2.846928@2] dwc_otg: Using Buffer DMA mode
[    2.846949@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.850819@2] dwc_otg: Working on port type = SLAVE
[    2.855706@2] dwc_otg: Dedicated Tx FIFOs mode

Thanks for your effort again, still stuck with the blue LED and logo on the screen

Full log in atasament, with android log after

 

defenv;sleep 1; saveenv;reboot

 

ok this is a kernel extracted from the libreelec version that you pointed replace your zImage with this

https://drive.google...36TeyDhNjBO6Drc

[boyz74]

Persian Prince, look log for AZBox Me.I have 1 image working but it does not have 2nd audio option?please help

 

ERROR: openpli-enigma2-image-1.0-r0 do_image_jffs2: Function failed: do_image_jffs2 (log file is located at /home/carlos/openpli-oe-core/build/tmp/work/azboxme-oe-linux/openpli-enigma2-image/1.0-r0/temp/log.do_image_jffs2.18533)
ERROR: Logfile of failure stored in: /home/carlos/openpli-oe-core/build/tmp/work/azboxme-oe-linux/openpli-enigma2-image/1.0-r0/temp/log.do_image_jffs2.18533
NOTE: recipe openpli-enigma2-image-1.0-r0: task do_image_jffs2: Failed
ERROR: Task (/home/carlos/openpli-oe-core/meta-openpli/recipes-openpli/images/openpli-enigma2-image.bb:do_image_jffs2) failed with exit code '1'
NOTE: Tasks Summary: Attempted 5522 tasks of which 5502 didn't need to be rerun and 1 failed.

[bruda]

thank you all for your work in mecool receivers.

 

 

I follow you all and you are great for your dedication in your free time

 

test done in k1 pro

 

start ok

 

community antenna tuner green screen in advanced mode

 

in successive starts it can already be changed. the maximum scanner 27.

 

when the deco reboots, the voltage of the tuner is lost and it is necessary to change it to return the signal.

 

the channels are not seen and are not heard.

 

wifi only 5g missing the virtual keyboard.

 

Thank you

[sauna]

k1plus coreelec putty log.

 

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.08.20 17:45:38 =~=~=~=~=~=~=~=~=~=~=~=

login as: root

root@192.168.0.126's password: 

##############################################

#                  CoreELEC                  #

#            https://coreelec.org            #

##############################################

 

CoreELEC (official): 8.95.0 (S905.arm)

[1;32mCoreELEC[1;32m:[1;34m~ [0m# lsmod | paste

http://ix.io/1kLF

[1;32mCoreELEC[1;32m:[1;34m~ [0m# dmesg | paste

http://ix.io/1kLG

[1;32mCoreELEC[1;32m:[1;34m~ [0m#

[zildan]

 

[    2.675397@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.685579@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    2.793438@2] dwc_otg: Core Release: 3.10a
[    2.793473@2] dwc_otg: Setting default values for core params
[    2.797643@2] dwc_otg: curmode: 0, host_only: 0
[    2.813535@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.813535@2] 
[    2.830880@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.830880@2] 
[    2.846928@2] dwc_otg: Using Buffer DMA mode
[    2.846949@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.850819@2] dwc_otg: Working on port type = SLAVE
[    2.855706@2] dwc_otg: Dedicated Tx FIFOs mode

Thanks for your effort again, still stuck with the blue LED and logo on the screen

Full log in atasament, with android log after

 

defenv;sleep 1; saveenv;reboot

 

ok this is a kernel extracted from the libreelec version that you pointed replace your zImage with this

https://drive.google...36TeyDhNjBO6Drc

 

 

 

Boot ok, black screen, ip, ssh etc.

I need ssh password.

Attached Files

•  putty.log.7.zip   18.13KB   3 downloads

[moham96]

 

 

[    2.675397@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.685579@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    2.793438@2] dwc_otg: Core Release: 3.10a
[    2.793473@2] dwc_otg: Setting default values for core params
[    2.797643@2] dwc_otg: curmode: 0, host_only: 0
[    2.813535@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.813535@2] 
[    2.830880@2] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.830880@2] 
[    2.846928@2] dwc_otg: Using Buffer DMA mode
[    2.846949@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.850819@2] dwc_otg: Working on port type = SLAVE
[    2.855706@2] dwc_otg: Dedicated Tx FIFOs mode

Thanks for your effort again, still stuck with the blue LED and logo on the screen

Full log in atasament, with android log after

 

defenv;sleep 1; saveenv;reboot

 

ok this is a kernel extracted from the libreelec version that you pointed replace your zImage with this

https://drive.google...36TeyDhNjBO6Drc

 

 

 

Boot ok, black screen, ip, ssh etc.

I need ssh password.

 

ssh has no password, you have to telnet and use the passwd to put a password

anyways alot of things will be broken since the kernel uses a different config for now.

 

Can you test this kernel

https://drive.google...E0Hft4kMNgtfLJo

[zildan]

[    2.542089@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[    2.557081@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[    2.559721@0] console [ttyS0] enabled
[    2.559721@0] console [ttyS0] enabled
[    2.566953@0] bootconsole [earlycon0] disabled
[    2.566953@0] bootconsole [earlycon0] disabled
[    2.576276@2] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f44c0
[    2.582783@2] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.592908@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    2.700876@0] dwc_otg: Core Release: 3.10a
[    2.700901@0] dwc_otg: Setting default values for core params
[    2.705052@0] dwc_otg: curmode: 0, host_only: 0
[    2.720964@0] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.720964@0]
[    2.738275@0] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.738275@0]
[    2.754313@0] dwc_otg: Using Buffer DMA mode
[    2.754331@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.758201@0] dwc_otg: Working on port type = SLAVE
[    2.763047@0] dwc_otg: Dedicated Tx FIFOs mode


Old problems, logo on screen and blue led

Attached Files

•  putty.log.8.zip   9.03KB   0 downloads

Edited by zildan, 20 August 2018 - 18:23.

[starz]

 

 

 

 

New test images for mecool devices

k1pro: http://www.mediafire...sdcard.zip/file

k2pro: http://www.mediafire...sdcard.zip/file

k2prov2: http://www.mediafire...sdcard.zip/file

k3pro: http://www.mediafire...sdcard.zip/file

k1plus: http://www.mediafire...sdcard.zip/file

I've tested k1plus image dear Persian Rrince.
-Boot is not normal for me, still same.boots or not boots and stays on black screen.
-When boot is normal,restarting the box and it goes to "no signal" on tv screen and no booting.
-There is no Wlan settings.
-Remote is OK.
-Network is OK.and webif is OK.

After a little digging it seems like the k1plus uses rtl8189etv for wifi, so we probably need to add the r8189 module and firmware again

Yes I think so,dear moham96.

Thanks

 

there are multiple rtl modules in the coreelec image and I don't know which one k1plus uses, can you boot a Coreelec/Libreelec image and give the output of

lsmod | paste

and

dmesg | paste

CoreELEC:~ # lsmod | paste
http://ix.io/1kMx

 

dmesg | paste
http://ix.io/1kMy

[starz]

 

New test images for mecool devices.

 

k1pro: http://www.mediafire...sdcard.zip/file

 

k2pro: http://www.mediafire...sdcard.zip/file

 

k2prov2: http://www.mediafire...sdcard.zip/file

 

k3pro: http://www.mediafire...sdcard.zip/file

 

k1plus: http://www.mediafire...sdcard.zip/file

I've tested for k1plus.boots OK.when restart the box boots again without problem.

-it's pink backround on box logo only.but boots normal:) thanks

-No wlan settings but I saw on github, moham96 add rtl8189es module for k1plus.thanks

[moham96]

 

[    2.542089@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[    2.557081@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[    2.559721@0] console [ttyS0] enabled
[    2.559721@0] console [ttyS0] enabled
[    2.566953@0] bootconsole [earlycon0] disabled
[    2.566953@0] bootconsole [earlycon0] disabled
[    2.576276@2] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f44c0
[    2.582783@2] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.592908@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[    2.700876@0] dwc_otg: Core Release: 3.10a
[    2.700901@0] dwc_otg: Setting default values for core params
[    2.705052@0] dwc_otg: curmode: 0, host_only: 0
[    2.720964@0] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.720964@0]
[    2.738275@0] WARN::dwc_otg_core_reset:5150: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
[    2.738275@0]
[    2.754313@0] dwc_otg: Using Buffer DMA mode
[    2.754331@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.758201@0] dwc_otg: Working on port type = SLAVE
[    2.763047@0] dwc_otg: Dedicated Tx FIFOs mode


Old problems, logo on screen and blue led

the strange thing is that I can't boot using the libreelec kernel you pointed, can you boot Coreelec ?

Also test this, it's a kernel built with coreelec config

https://drive.google...jfQ4EcpJGfG_wGm

If this doesn't work I will prepare boot files as android image which might solve this issue

[zildan]

Boot ok, telnet ok, no hdmi output.

 

Alien5 use android kernel config !

Attached Files

•  putty.log9.zip   21.93KB   2 downloads

Edited by zildan, 20 August 2018 - 21:01.

[frankviana]

Here the log using UART cable (gnd, tx, rx) and official firmware Android. Later I'll post log using OpenPli test image.

 

K1 plus: This receiver don't have tuner dtv, only tv box, but accepts same image DTV box.

 

 

Attached Files

•  SX88_2018-08-20_18-12-06-K1 PLUS.log   81.67KB   7 downloads

[Persian Prince]

New test images for mecool devices.

 

k1pro: http://www.mediafire...sdcard.zip/file

 

k2pro: http://www.mediafire...sdcard.zip/file

 

k2prov2: http://www.mediafire...sdcard.zip/file

 

k3pro: http://www.mediafire...sdcard.zip/file

 

k1plus: http://www.mediafire...sdcard.zip/file

[moham96]

The mainline linux for amlogic devices is getting support for hardware decoding

https://github.com/E...mlogic-v4l2-m2m

I haven't tried it yet but from reading it seems it works with mainline gstreamer without any plugins or extra patches.

the linux-meson wiki states that the dvb part is not supported yet but I see at least one media_tree repo with amlogic drivers

https://github.com/afl1/media_tree

I think this is intended to be used with mainline linux

 

also I think using mainline linux we don't need to use the amldecoder , correct me if I'm wrong.

 

What machines currently supported that uses mainline linux and gstreamer without extra gst-plugins or patches ? I need to look into their recipes.

 

Regards

[belaid38]

The mainline linux for amlogic devices is getting support for hardware decoding

https://github.com/E...mlogic-v4l2-m2m

I haven't tried it yet but from reading it seems it works with mainline gstreamer without any plugins or extra patches.

the linux-meson wiki states that the dvb part is not supported yet but I see at least one media_tree repo with amlogic drivers

https://github.com/afl1/media_tree

I think this is intended to be used with mainline linux

 

also I think using mainline linux we don't need to use the amldecoder , correct me if I'm wrong.

 

What machines currently supported that uses mainline linux and gstreamer without extra gst-plugins or patches ? I need to look into their rec

wetek play 2  is  supported 

https://github.com/s...2m/conf/machine

[wu-li]

SPARK 7111 ?

where to replace files - pti.ko and stmdvb.ko (a lot of errors - like in post # 1042)

stmdvb.ko - 140.9 kB

pti.ko - 16.1 kB

[moham96]

 

The mainline linux for amlogic devices is getting support for hardware decoding

https://github.com/E...mlogic-v4l2-m2m

I haven't tried it yet but from reading it seems it works with mainline gstreamer without any plugins or extra patches.

the linux-meson wiki states that the dvb part is not supported yet but I see at least one media_tree repo with amlogic drivers

https://github.com/afl1/media_tree

I think this is intended to be used with mainline linux

 

also I think using mainline linux we don't need to use the amldecoder , correct me if I'm wrong.

 

What machines currently supported that uses mainline linux and gstreamer without extra gst-plugins or patches ? I need to look into their rec

wetek play 2  is  supported 

https://github.com/s...2m/conf/machine

 

I don't mean supported in yocto, I mean supported in openpli, and enigma2 is working