2740 replies to this topic

[Persian Prince]

 

 

I think there might be some differences between S905 and S905D regarding dvb handling

can someone with a S905D device test the images and see if they see any picture from dvb ?

I tested two images on my k1 pro, uploaded by ftp21_ and Persian Prince respectively.

ftp21_:

There were 4 tuner types visible in tuner setup, i.e, DVB-S, DVB-T, DVB-C & ATSC.

I tried DVB-S scan and it tuned and saved channels on some frequencies (not all).

No video or audio on any channel.

Signal level was visible on infobar all saved channels.

Persian Prince:

There were 2 tuner types visible in tuner setup, i.e, DVB-S & DVB-T only.

I tried DVB-S scan and it did not tune or saved any channel (as had been in earlier versions of test images).

 

Why persian prince's images don't work !! @persian any Idea ?

 

you should see four types, if you see only two then probably the dvb drivers are not loaded and enigma is reading the hardcoded nim_sockets

try to ssh into the device and run

lsmod

also boot into the working image(ftp21_)  and run this

echo "dmx0" > /sys/class/stb/source

and then tune into a channel and see if this changes anything

 

 

No idea, I did use pli-extras without any local changes ...

[Persian Prince]

New test images without "alien5-enigma2.patch"

 

k1pro: http://www.mediafire...1pro_sdcard.zip

 

k2pro: http://www.mediafire...2pro_sdcard.zip

 

k2prov2: http://www.mediafire...rov2_sdcard.zip

 

k3pro: http://www.mediafire...3pro_sdcard.zip

 

k1plus: http://www.mediafire...plus_sdcard.zip

[martossien]

For other reason i play with the ely kernel (amlogic)

https://github.com/Elyotna/linux

4.18 Hacking in a V4L2 M2M decoder for AMLogic SoCs

But i know all this change going in to librelec kernel after

New official support is for the 4.19 kernel

Edited by martossien, 11 August 2018 - 08:35.

[algdu83]

 

New test images without "alien5-enigma2.patch"

 

k1pro: http://www.mediafire...1pro_sdcard.zip

 

 

Same problem

Is boot

I have test with my favoris i have signal with all channels but not working

No audio, no video

thanks

[algdu83]

If it's a problem of tuner, why the channels iptv does not work either?
can be a decoding problem
test your iptv or moviz if it opens

Edited by algdu83, 11 August 2018 - 08:57.

[Persian Prince]

When you can't play anything it means the problem is gstreamer.

[takitr]

K3 pro should be dont work because s912 has not puplic mali t830 linux userspace driver that only has android libhybrit driver.

Edited by takitr, 11 August 2018 - 09:33.

[algdu83]

When you can't play anything it means the problem is gstreamer.

I think too
but since webif does not work either with VLC

[ledtou]

K3 pro should be dont work because s912 has not puplic mali t830 linux userspace driver that only has android libhybrit driver.

Me too i have k3 pro s912 i test image no boot just stuck in logo mecool k3 pro

[takitr]

When you can't play anything it means the problem is gstreamer.

I think too
but since webif does not work either with VLC

Can you try handphone (vuplayer apk) or linux or Windows pc overlan connecting. May be streaming your channels enigma2 overlan device

Edited by takitr, 11 August 2018 - 11:05.

[moham96]

When you can't play anything it means the problem is gstreamer.

I I play a file from gst-launch using playbin then the video goes through dvbvideosink and it doesn't detect the codec

 

root@k2pro:~# gst-launch-1.0 playbin uri=file:///home/root/test.mkv
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
ERROR: from element /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0: There is no codec present that can handle the stream's type.
Additional debug info:
../git/gstdvbvideosink.c(1810): gst_dvbvideosink_set_caps (): /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0:
hardware decoder can't handle streamtype 1
ERROR: pipeline doesn't want to preroll.
Setting pipeline to NULL ...
Freeing pipeline ...
root@k2pro:~#
 

But If I remove the dvbvideosink plugins I can play files because it goes through  amlogic plugins.

Or I can set the video sink on the pipeline:

st-launch-1.0 playbin video-sink="amlvsink " uri=file:///home/root/test.mkv
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
[codec_init][725]############ pcodec->stream_typ 1
WARNING: from element /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:abin/GstAlsaSink:alsasink0: Could not get/set settings from/on resource.
Additional debug info:
../../../git/ext/alsa/gstalsasink.c(502): set_hwparams (): /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:abin/GstAlsaSink:alsasink0:
Unable to set buffer time 200000 for playback: Invalid argument
Redistribute latency...
Pipeline is PREROLLED ...
Setting pipeline to PLAYING ...
New clock: GstAudioSinkClock

I can only hear audio and no video for now but at least it plays.

 

So this a problem with the dvbvideosinkplugins since they don't detect libamcodec

 

I think openatv doesn't use dvbvideosink plugin and that's why it works, correct me if I'm wrong.

 

Can we tell enigma2 to use the amlvsink as a video sink and amlasink as audio sink or are we stuck with dvbvideosink  ?

 

note that this problem is not only with mecool devices, alien5 also has the same problems on pli

Edited by moham96, 11 August 2018 - 11:08.

[moham96]

 

When you can't play anything it means the problem is gstreamer.

I I play a file from gst-launch using playbin then the video goes through dvbvideosink and it doesn't detect the codec

 

root@k2pro:~# gst-launch-1.0 playbin uri=file:///home/root/test.mkv
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
ERROR: from element /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0: There is no codec present that can handle the stream's type.
Additional debug info:
../git/gstdvbvideosink.c(1810): gst_dvbvideosink_set_caps (): /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0:
hardware decoder can't handle streamtype 1
ERROR: pipeline doesn't want to preroll.
Setting pipeline to NULL ...
Freeing pipeline ...
root@k2pro:~#
 

But If I remove the dvbvideosink plugins I can play files because it goes through  amlogic plugins.

Or I can set the video sink on the pipeline:

st-launch-1.0 playbin video-sink="amlvsink " uri=file:///home/root/test.mkv
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
[codec_init][725]############ pcodec->stream_typ 1
WARNING: from element /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:abin/GstAlsaSink:alsasink0: Could not get/set settings from/on resource.
Additional debug info:
../../../git/ext/alsa/gstalsasink.c(502): set_hwparams (): /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:abin/GstAlsaSink:alsasink0:
Unable to set buffer time 200000 for playback: Invalid argument
Redistribute latency...
Pipeline is PREROLLED ...
Setting pipeline to PLAYING ...
New clock: GstAudioSinkClock

I can only hear audio and no video for now but at least it plays.

 

So this a problem with the dvbvideosinkplugins since they don't detect libamcodec

 

I think openatv doesn't use dvbvideosink plugin and that's why it works, correct me if I'm wrong.

 

Can we tell enigma2 to use the amlvsink as a video sink and amlasink as audio sink or are we stuck with dvbvideosink  ?

 

note that this problem is not only with mecool devices, alien5 also has the same problems on pli

 

Small correction I can actually see the video but I have to run enigma2 before I run gst-launch ,apparently, the framebuffer needs to be setup by enigma2 first

 

[moham96]

mecool users:

update and build again, I added a demuxer workaround, now enigmacan grab the epg but still no image and I see timeout reading PAT,maybe this is a problem with the channel I tuned to so you need to try on a different channel.

 

one channel I tuned to I think streamed the ts stream but the amlogic codec crashed, unfortunately I can't reproduce so I can't find the problem

[starz]

mecool users:
update and build again, I added a demuxer workaround, now enigmacan grab the epg but still no image and I see timeout reading PAT,maybe this is a problem with the channel I tuned to so you need to try on a different channel.

one channel I tuned to I think streamed the ts stream but the amlogic codec crashed, unfortunately I can't reproduce so I can't find the problem

Ok.I'll build and test it.

Regards

[engineerkhan15]

mecool users:

update and build again, I added a demuxer workaround, now enigmacan grab the epg but still no image and I see timeout reading PAT,maybe this is a problem with the channel I tuned to so you need to try on a different channel.

 

one channel I tuned to I think streamed the ts stream but the amlogic codec crashed, unfortunately I can't reproduce so I can't find the problem

I compiled the image and tested on my K1 Pro.

I also get no video or audio on saved channel.

After few seconds on a saved (FTA SD channel) I get message:

No data on transponder!

(Timeout reading PAT)

[Persian Prince]

Also test audio/video playback as we did some changes.

[engineerkhan15]

Also test audio/video playback as we did some changes.

I tried to play an audio file (mp3) and video file (mp4) in mediaplayer plugin but both did not play.

I got an error message at video file "This receiver cannot decode streams".

[wu-li]

SPARK7111

 

OSCAM - NG

 

NO IMAGE AND SOUND

 

Live Log:

 

2018/08/12 10:54:22 349B2779 c (ecm) d...u (0...8/5C00/1135/64:D...7): found (809 ms) by R-1 - ...

 

shows everything - ecm and etc ...

[Persian Prince]

New test images ...

 

k1pro: http://www.mediafire...sdcard.zip/file

 

k2pro: http://www.mediafire...sdcard.zip/file

 

k2prov2: http://www.mediafire...sdcard.zip/file

 

k3pro: http://www.mediafire...sdcard.zip/file

 

k1plus: http://www.mediafire...sdcard.zip/file

[BarviX]

SPARK7111

 

OSCAM - NG

 

NO IMAGE AND SOUND

 

Live Log:

 

2018/08/12 10:54:22 349B2779 c (ecm) d...u (0...8/5C00/1135/64:D...7): found (809 ms) by R-1 - ...

 

shows everything - ecm and etc ...

replace module pti.ko

http://taapat.ho.ua/...-r0.4_spark.ipk