5 replies to this topic

[mattiL]

Had a crash last night, second one in a couple of weeks.

The STB was in standby doing a single recording, I turned it on to watch another channel,

doing some zapping for a few minutes and wham, it froze up.

 

I had to restart the receiver via SSH so most likely only enigma froze (with the little circle of dots shown in the upper left corner).

 

The recording was on a channel decoded by oscam towards a CanalDigital card in the lower card reader (strangely enough identified as upper by OpenPLi).

 

Second peculiarity, decoding time in GUI is presented in seconds (316s) instead of milliseconds, se attached screen shot.

 

Receiver Vu+ Duo2

Enigma version 2018-01-07 6.1-release

DVB driver version 2017-12-04

 

 

Time to updated OpenPLi to a more recent version perhaps?

Attached Files

•  dmesg.txt   2.69KB   4 downloads
•  Screen Shot 2018-03-11 at 14.34.09.png   1.02MB   3 downloads

[WanWizard]

Looks like a crash in the driver:

CPU 0 Unable to handle kernel paging request at virtual address 0000003c, epc == e0c1856c, ra == e0c18564
Oops[#1]:
CPU: 0 PID: 526 Comm: oscam Tainted: P           O 3.13.5 #1
task: cfe74020 ti: ccf14000 task.ti: ccf14000
$ 0   : 00000000 10008700 00000000 e0bf0000
$ 4   : 00000000 e0f19498 00000005 ce18d880
$ 8   : 20006f2a 84080008 800f6234 00000000
$12   : 771fab58 00591910 0043021c 00591910
$16   : 00000000 e1420000 00000200 cd48e280
$20   : e1368cf4 00000200 e0b90000 e0c30000
$24   : 771fab90 e0ca2ef4                  
$28   : ccf14000 ccf15c58 e0c30000 e0c18564
Hi    : 00042b8b
Lo    : f218c240
epc   : e0c1856c NEXUS_PidChannel_Close_impl+0x34/0x60 [dvb_bcm7424]
    Tainted: P           O
ra    : e0c18564 NEXUS_PidChannel_Close_impl+0x2c/0x60 [dvb_bcm7424]
Status: 10008703	KERNEL EXL IE 
Cause : 0080000c
BadVA : 0000003c
PrId  : 00025a11 (Broadcom BMIPS5000)
Modules linked in: ipv6 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 fpga_directc(PO) brcmfb(O) dvb_bcm7424(PO) procmk(O)
Process oscam (pid: 526, threadinfo=ccf14000, task=cfe74020, tls=77206930)
Stack : ce18d800 e0ca2f14 00000000 00000000 00000000 e1b1162c 00000000 e0c29568
	  00000004 00000000 00000000 00000000 00000000 00000001 00000000 e0b9312c
	  00000000 00000000 01010101 00000000 00000000 00000000 00000000 00000000
	  00000000 00000000 00000000 00000000 cf7b3604 8006d194 00000000 00000000
	  00000000 80063e98 ccf15d00 00000068 e12e0000 e0bb103c 82013500 80702080
	  ...
Call Trace:
[<e0c1856c>] NEXUS_PidChannel_Close_impl+0x34/0x60 [dvb_bcm7424]
[<e0c29568>] NEXUS_PidChannel_Close+0x28/0x3c [dvb_bcm7424]
[<e0b9312c>] bcm7335_demux_release_priv+0x52c/0x11a4 [dvb_bcm7424]

The seconds vs milliseconds issue is an Oscam configuration item.

[mattiL]

Ok, I will check if I can find the oscam config parameter responsible for this erroneous presentation.

Thank's!

[janejak]

om my CanalDigital card

[Canal Digital Nordic] upper (253 ms)

i use oscam

Edited by janejak, 12 March 2018 - 19:16.

[mattiL]

om my CanalDigital card

[Canal Digital Nordic] upper (253 ms)

i use oscam

I found the setting to get back the "ms" presentation again, it was set to "oscam (ms)" and changing it to "oscam" changed the presentation to show "ms" again (seems a bit backward to me).

Attached Files

•  Screen Shot 2018-03-12 at 21.17.52.png   56.72KB   5 downloads

Edited by mattiL, 12 March 2018 - 21:18.

[janejak]

this is my setting

Attached Files

•  2018-03-13.jpg   57.36KB   4 downloads