Jump to content


Photo

Scanning issue: Dead/out of footprint transponders


  • Please log in to reply
49 replies to this topic

Re: Scanning issue: Dead/out of footprint transponders #41 littlesat

  • PLi® Core member
  • 57,173 posts

+698
Excellent

Posted 14 May 2018 - 13:41

FYI

https://github.com/O...0820b7522f33f81


WaveFrontier 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 7E | 5E | 1W | 4/5W | 15W


Re: Scanning issue: Dead/out of footprint transponders #42 WanWizard

  • PLi® Core member
  • 70,530 posts

+1,811
Excellent

Posted 14 May 2018 - 13:46

I'll back-port it to 6.2-release, pending the discussion about the timeout time.


Edited by WanWizard, 14 May 2018 - 13:48.

Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Scanning issue: Dead/out of footprint transponders #43 Abu Baniaz

  • PLi® Contributor
  • 2,499 posts

+64
Good

Posted 14 May 2018 - 13:46

Yes, that is what I applied. Sorry, should have been clearer.

 

https://github.com/O...f530834103dbb07



Re: Scanning issue: Dead/out of footprint transponders #44 pieterg

  • PLi® Core member
  • 32,766 posts

+245
Excellent

Posted 14 May 2018 - 14:05

I applied this to OpenVix and built an image. It works, thanks.

It waits 5/6 minutes before going to second TP. Can this be reduced to 2 minutes?


the total timeout depends on the turning angle, and the turning speed which is used in the timeout calculation is very conservative (because the motor might be very slow): 2 seconds per degree (plus some constant factor)
This value is not a setting, it cannot be tweaked by users.

Re: Scanning issue: Dead/out of footprint transponders #45 Huevos

  • PLi® Contributor
  • 4,662 posts

+163
Excellent

Posted 14 May 2018 - 15:54

It waits 5/6 minutes before going to second TP. Can this be reduced to 2 minutes?

Reducing to 2 minutes would break scanning on my positioner.



Re: Scanning issue: Dead/out of footprint transponders #46 Huevos

  • PLi® Contributor
  • 4,662 posts

+163
Excellent

Posted 14 May 2018 - 15:57

 

I applied this to OpenVix and built an image. It works, thanks.

It waits 5/6 minutes before going to second TP. Can this be reduced to 2 minutes?


the total timeout depends on the turning angle, and the turning speed which is used in the timeout calculation is very conservative (because the motor might be very slow): 2 seconds per degree (plus some constant factor)
This value is not a setting, it cannot be tweaked by users.

 

There is no way to know the turning angle, or is there? My receiver has 2 motorised dishes attached. How is enigma supposed to know which dish the stored angle corresponds to?


Edited by Huevos, 14 May 2018 - 15:58.


Re: Scanning issue: Dead/out of footprint transponders #47 pieterg

  • PLi® Core member
  • 32,766 posts

+245
Excellent

Posted 14 May 2018 - 18:15

Only one dish per tuner I assume?
The angle is known for each tuner, the difference between old/new angle determines the timeout.

Re: Scanning issue: Dead/out of footprint transponders #48 WanWizard

  • PLi® Core member
  • 70,530 posts

+1,811
Excellent

Posted 14 May 2018 - 21:22

Backported, will be in 6.2-release tomorrow.


Currently in use: VU+ Duo 4K (2xFBC S2), VU+ Solo 4K (1xFBC S2), uClan Usytm 4K Ultimate (S2+T2), Octagon SF8008 (S2+T2), Zgemma H9.2H (S2+T2)

Due to my bad health, I will not be very active at times and may be slow to respond. I will not read the forum or PM on a regular basis.

Many answers to your question can be found in our new and improved wiki.


Re: Scanning issue: Dead/out of footprint transponders #49 Huevos

  • PLi® Contributor
  • 4,662 posts

+163
Excellent

Posted 14 May 2018 - 22:06

2 dishes. 1 C-band and 1 ku. Used to be on the same tuner but not currently.

Re: Scanning issue: Dead/out of footprint transponders #50 Abu Baniaz

  • PLi® Contributor
  • 2,499 posts

+64
Good

Posted 14 May 2018 - 23:30

Reducing to 2 minutes would break scanning on my positioner.

The "initial wait" time reduction has already been ruled out.


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users