57 replies to this topic

[gericooper]

Hallo,

habe das Update von 6.1 auf 6.2 via flash durchgeführt.

Jetzt wird meine externe Festplatte nicht mehr erkannt.

Auch im Devicemanager wird sie nicht angezeigt.

Geh ich wieder zurück auf 6.1 ist alles wie gehabt und die Festplatte funktioniert wieder tadellos.

 

 

[Pumuckel]

Poste mal die Ausgabe von diesem Telnetbefehl:

 

df -h

 

 

... Pumuckel

[gericooper]

wird im openpli 6.1 angezeigt

 

Filesystem                Size      Used Available Use% Mounted on
ubi0:rootfs             437.4M    177.5M    259.9M  41% /
devtmpfs                254.2M      4.0K    254.2M   0% /dev
tmpfs                    64.0K         0     64.0K   0% /media
tmpfs                   254.3M    120.0K    254.2M   0% /var/volatile
/dev/sdb1                 1.8T      1.4T    469.6G  75% /media/usb

[Pumuckel]

und die Ausgbabe beim 6.2?

 

 

... Pumuckel

Edited by Pumuckel, 2 June 2018 - 19:57.

[gericooper]

wird überhaupt nicht angezeigt.

Versteh das nicht.

Auch im Devicemanager nichts.

Hab eine Seagate Expansion

Edited by gericooper, 2 June 2018 - 20:01.

[Pumuckel]

Welche Ausgabe kommt bei Telnet bei diesem Befehl?

opkg list-installed *usbserial*

... Pumuckel

Edited by Pumuckel, 2 June 2018 - 20:04.

[gericooper]

kommt nichts.

nur ohne *usbserial* bekomm ich was.

[Pumuckel]

Dann ist das Plugin "usbserial" nicht installiert --> Plugin installieren (findest Du unter "drivers") , Box neu booten und dann sollte die Festplatte erkannt werden.

 

 

... Pumuckel

[gericooper]

Jetzt kommt

enigma2-plugin-drivers-usbserial - 1.0-r0.2  
kernel-module-usbserial - 4.10.6-r3.0.1    

 

aber wieder keine festplatte

[gericooper]

beim befehl df-h kommt jetzt

Filesystem                Size      Used Available Use% Mounted on    
ubi0:rootfs             437.4M     80.6M    356.8M  18% /             
devtmpfs                157.0M      4.0K    157.0M   0% /dev          
tmpfs                    64.0K         0     64.0K   0% /media        
tmpfs                   157.2M    112.0K    157.1M   0% /var/volatile

[Pumuckel]

Welchen Receiver verwendest Du denn?

 

 

... Pumuckel

[gericooper]

Formuler F1

[gericooper]

ist hier nicht ein ähnliches Problem?

 

https://forums.openp...sb-hdd-problem/

Edited by gericooper, 2 June 2018 - 20:49.

[heimiu]

I do have the same receiver with the same problem,

 

lsusb shows this device

Bus 004 Device 004: ID 174c:55aa

It is an ASMedia Chip (ASM1153E) which does the usb/sata communication. I tried a 3,5/2,5 inch dock with the same chipset which is also not working. An ASM1053 does have the same problems.

dmesg is just shows a new device and not more

I tried an external USB to Sata Cable (with hat the logic in the plug -- this worked:

it is a usb id 1f75:0621 which is a Innotec IS621 Chipset

[gericooper]

does it work with the new image?

openpli-6.2-release-formuler1-20180605_usb.zip

[heimiu]

Unfortunately not. And I did not need any extra package in 6.1 to get the hd working. I managed to get a USB/eSATA case with a SataLink SPIF225A-HF021 next week. Let's see.

[WanWizard]

After you have plugged in your USB device, issue the commands

dmesg
cat /var/log/messages

and post the last 20 lines or so of each, so we can see what is or isn't detected. Without this, we're guessing...

[heimiu]

As I said, its only one relevant line: (dmesg)

 

[   11.604000] __clk_enable: network [1]

[   11.604000] __clk_enable: enet [1]

[   11.604000] bcm40nm_pm_genet_enable 00

[   11.728000] bcmgenet bcmgenet.0: configuring instance for external RGMII (TX delay)

[   12.898000] bcmgenet bcmgenet.0 eth0: Link is Down

[   15.085000] bcmgenet bcmgenet.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx

[   18.241000] NET: Registered protocol family 10

[   18.247000] Segment Routing with IPv6

[ 4622.322000] usb 4-1: new high-speed USB device number 2 using ehci-brcm

 

/var/log/messages:

Jun 10 13:33:44 formuler1 authpriv.warn dropbear[20814]: lastlog_openseek: /var/log/lastlog is not a file or directory!

Jun 10 13:34:06 formuler1 user.info kernel: [ 4622.322000] usb 4-1: new high-speed USB device number 2 using ehci-brcm

 

--- lsusb

Bus 004 Device 002: ID 174c:55aa

 

The same device under ubuntu on a usb3 port:

usb 9-1: new SuperSpeed USB device number 2 using xhci_hcd

usb 9-1: New USB device found, idVendor=174c, idProduct=55aa

usb 9-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1

usb 9-1: Product: USB3-SATA-Device

usb 9-1: Manufacturer: ASMedia

usb 9-1: SerialNumber: 20150324000D7D

scsi host9: uas

scsi 9:0:0:0: Direct-Access     HGST HTS 541010A9E680     0    PQ: 0 ANSI: 6

sd 9:0:0:0: Attached scsi generic sg8 type 0

sd 9:0:0:0: [sdh] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)

sd 9:0:0:0: [sdh] 4096-byte physical blocks

sd 9:0:0:0: [sdh] Write Protect is off

sd 9:0:0:0: [sdh] Mode Sense: 43 00 00 00

sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

 

and thats the lsusb entry:

Bus 002 Device 016: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge

[WanWizard]

Is says it's an USB3-SATA bridge, afaik the box doesn't have USB3 support?

[betacentauri]

It should be downwards compatible so that you can use it with usb 2.0